How do you replace the rear wipers? How do you change the wipers?

1. Lift the metal wiper arm away from the windshield and keep it stable perpendicular to the windshield.

2. Press down on the plug and remove the old wiper blades to separate them from the metal arm.

3. Insert the new wiper and gently turn the new wiper blade.

4. Finally, put the wiper back on the windshield until the hook clicks into place to secure.

Generally, the service life of the wiper is one year. It doesn't matter if it's from a 4S store or bought from outside.

Determine that the wiper is time to change: Clean the glass surface before confirming. Touch the surface of the glass with your hands to make sure that the glass is free of scratches and raised particles. Wipe the wiper strip with a cotton cloth, strictly prohibit vigorous efforts, and confirm whether the strip is scratched, deformed or jagged.

Under normal circumstances, if there is still a waterline or the sound is particularly loud, or it is not clear, you can consider replacing the wipers.

Explanation: Wipers, also known as wipers, water picks, wipers or windshield wipers, are equipment used to brush and scrape away rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. Because of the legal requirements, cars in almost all places carry windshield wipers.

Vehicles such as hatchbacks and minivans are also equipped with wipers in the rear windows. In addition to automobiles, windshield wipers are also installed in other means of transportation, such as trains and trams. Some part of the engineering equipment, I hope thank you.

How to replace the wipers, you will know when you look at it.

The steps to replace the wiper are as follows:In the first step, lift the metal wiper arm from the windshield, perpendicular to the windshield position and hold it stable.

In the second step, press the stopper and remove the old wiper blades, separating them from the metal arm.

Step 3: Insert the new wipers, gently turn the new wipers until the hook clicks into place and is secured, and put the wipers back on the windshield.

Wipers, also known as wipers, water dials, wipers or windshield wipers, are composed of electric motors, reducers, four-link mechanisms, wiper arm mandrels, wiper blade assemblies, etc., and are used to brush and scrape the equipment that is attached to the windshield of the vehicle to remove rain and dust to improve the visibility of the driver and increase driving safety.

1. First lift the wiper from the windshield, as shown in the figure below

2. Keep the wiper stable, as shown in the figure below

3. Next, find the plug on the contact position between the rubber wiper blade of the wiper and the metal arm, as shown in the figure below

4. Press the plug to remove the wiper strip, as shown in the figure below

5. Insert the new adhesive strip of the wiper and stick the hook card firmly, as shown in the figure below

6. Finally, put the wiper back on the windshield, as shown in the figure below

1. Taking Kia Sportage as an example, there is a card button on the middle buckle of the wiper, which needs to be pressed to remove it when disassembled;

2. The end of the wiper mainly plays the role of fixing the wiper blade;

3. Lift the middle position of the wiper with your hand, and press the buckle to separate the wiper;

4. Then you can pull out the wiper arm to the left, so that the wiper and the wiper arm can be separated;

5. Put on a new wiper, pay attention to the model to be consistent with the original car, and install it back according to the method just now;

6. When installing it back, it should be stuck in place to prevent the wiper from falling off;

7. After that, drag out the protective cover on the wiper, so that you can use the wiper normally when you put it back;

8. Try the effect again after replacement.

How to replace the wipers, you will know when you look at it.

To replace the wiper, first remove the wiper, then remove the rubber strip, install the new rubber strip, and reinstall the wiper back on, the specific steps are as follows:

1. Remove the wipers

This step is relatively simple, pull up the wiper spring arm lever, first stand up the wiper, press and hold the clip in the middle of the trouble, and remove the wiper of the original car from the side, but be careful not to let the rocker arm bounce back and break the front windshield.

2. Disassemble the wiper strip

Removed wipers with a plastic cap at each end. One of them is fixed and the other is active. Use a slight force to pry open the fixed cap with a screwdriver, and do not rush to pull out the strip at this time.

Because there is also a metal buckle, which plays the role of clamping and fixing the adhesive strip, use a screwdriver to gently pry it open a little, and the adhesive strip can be pulled out smoothly.

3. Replace the rubber strip

There are two and a half layers of rubber strips from the inside to the outside (the outermost is the rubber "blade liquid limb") of the wipers), and the innermost one layer is stuck in the groove of the wiper, loaded into it, fastened with the metal buckle, and covered with a plastic cap, just like the original factory.

4. Install wipers

the front end of the clip in the middle to make it easier to install. After inserting the clip in the middle, it is tightened, and it is in place when you hear a click. Install the wiper in the passenger seat, look at the direction, also tighten, and hear a click, that is, the installation is completed.

Reasons to replace the wipers

Because the rubber strip on the wiper blade is made of rubber, it will age after a long time, which is manifested as deformation, embrittlement, and then cracking, resulting in the inability to scrape the water on the windshield, which then affects the line of sight, vision, and brings danger to driving, so the maintenance of the car wiper is also important, although many people ignore it.