What is the problem with the Canon GO405 copier s E001

I'll teach you, the machine is GP405, not GO, 001 is the fixing overtemperature caused by voltage instability, and I'll teach you how to cancel it below.

1. Press the rice key, which is the one below the question mark.

2, the numbers 2 and 8 are pressed at the same time.

3. Press the rice button again.

4. The screen changes to the maintenance mode.

5. Tap on the first word on the screen copies

6. Click on the word that starts with fun above.

7. There is a clear in the middle of the screen, tap it.

8. Click ERR, then click OK in the bottom right corner

9. Press the yellow reset button to turn off the power for 20 seconds.

Note: Sometimes the ** screen will go black quickly, at this time you have to operate quickly, and the first 3 steps are pressed right and the back is simple.

Canon 405 Error ** table, see which one your machine belongs to.

E001 0001 Main Fixing Overtemperature The main thermistor TH1 detects that the fixing temperature exceeds 220 degrees for 2 seconds, and the main thermistor TH1 is short-circuited.

J426 white wire 0 ohms, normal 1000 1400K ohms);

E001 0002 SUB THERMISTOR OVERTEMPERATURE The subthermistor TH2 detects that the fusing temperature exceeds 235 degrees for 2 seconds, and the subthermistor TH2 is short-circuited.

J426 black line 0 ohm female, normal 40 50k ohm female); J426 (black line, about 40 50k ohms).

E001 0003 Fixing Overtemperature (Subthermistor Th2 Open Circuit) The subthermistor Th2 detects that the fixing temperature exceeds 235 degrees for 2 seconds, and the subthermistor Th2 is open.

Good luck.

Dear Hello, the Canon printer warns that the e05 is because of the cartridge recognition failure, the Canon printer displays the e05, that is, the ink cartridge cannot be recognized or is incompatible, or the ink cartridge is not installed correctly, it is recommended to clear or replace the ink cartridge to solve it, and you need to replace the ink cartridge with a new one. The steps to solve the problem are as follows:1. Cause 1:

It may be because the cartridge is incompatible or cannot be recognized by the machine. Workaround: Need to replace the cartridge with a new one.

2. Reason 2: The cartridge is installed incorrectly. Workaround:

Remove the cartridge and install it the correct way. 3. Reason 3: It may be because of a software failure Solution:

Press the Stop reset button first, then press the power button to power on (don't let go); While pressing the power button without letting go, release the Stop Reset button. Since its establishment in 1937, Canon is a leading global conglomerate for the production of imaging and information products in Japan, and has expanded its business to various fields through unremitting efforts over the years. Hopefully, the Appeal Answers will help you <>

Reason 1: It may be because the cartridge is incompatible or cannot be recognized by the machine. Workaround:

A new cartridge needs to be replaced. Canon printer shows e05 what to do Reason 2: The cartridge is not installed correctly.

Solution: Remove the cartridge and install it in the correct way. Canon printer shows e05 how to fix 3 reasons 3:

It may be because of the software failure solution: 1. Press the stop reset button first, and then press the power button to power on (don't let go); While pressing the power button without letting go, release the Stop Reset button. 2. Then press the Stop Reset button five times again, and release the Power button and the Stop Reset button at the same time.

3. After the revelation is completed, it is displayed as"0", open the software again, and then click "Clear". 4. When the response is finished, turn off the machine and turn it on again, and clear it.

Causes

1. The circuit board of the inverter is faulty.

Solution: Replace and repair the circuit board of the inverter.

2. The membrane switch panel is disconnected.

Solution: Repair and replace the membrane switch.

3. The current flow of the socket is insufficient.

Solution: Change to a socket with higher power.

Precautions1. The environment in which the photocopier is placed should be suitable, and it should be paid attention to high temperature, dust, and shockproof, and it should also be placed in a place that is not easy to touch water. Do not place too heavy items on the photocopier to avoid the upper panel being deformed by heavy pressure and affecting the use. The most important thing is to place the photocopier in a well-ventilated place, because the photocopier will produce trace amounts of ozone when working, and long-term exposure is harmful to the health of the operator.

Second, we should also pay attention to the power supply of the copier, the rated voltage of the photocopier is generally between 200V and 240V, and the voltage of the power socket is too high or too low will affect the normal operation of the copier. Whether you are plugging or unplugging the power supply, or troubleshooting the paper jam, you should turn off the power switch of the copier before operating, otherwise it will shorten the service life of the copier and cause failure.

3. Reasonable preheating is very helpful to extend the copier, and the photocopier should be preheated for about half an hour every day to keep the copier. And when there is no copying task for a long time, the power of the copier should be turned off to save energy.

Home-Reset-Previous Go directly to the repair mode and operate the copier in the following order

function

clearerr then prompts OK, click the copy button, turn off the copier, and restart it.

Home - Reset - Previous - Home Page.

Enter repair mode.

copier- function- clear-err- ok restart the printer.

Generally, it is a fixing error.

What should I do if the Canon printer error message "e000001-0001" is displayed?

1. The error at the beginning of E is a maintenance fault, which is a fault that you cannot eliminate yourself. Specific faults need to be checked by contacting a Canon-certified repair station. 2. The temperature rise of the fixing unit is detected (by the subthermistor), and the subthermistor detects an abnormal high temperature (295 degrees Celsius) when the temperature is controlled.

The following routine maintenance needs to be done:1Check the fuser unit plug.

2.Replace the fuser unit. 3.

Replace the DC control circuit board.

Summary. Dear, hello, I'm glad to answer for you, Canon printer warning E05 is because of cartridge recognition failure, Canon printer shows E05, that is, it means that the cartridge cannot be recognized or is incompatible, or the cartridge is not installed correctly, it is recommended to clear or replace the cartridge to solve it, and you need to replace a new cartridge. The steps to resolve the problem are as follows:

1. Reason 1: It may be because the cartridge is incompatible or cannot be recognized by the machine. Workaround:

A new cartridge needs to be replaced. 2. Reason 2: The cartridge is installed incorrectly.

Solution: Remove the cartridge and install it in the correct way. 3. Reason 3:

It may be because of a software glitch Solution: Press the Stop reset button first, and then press the power button to power on (don't let go); While pressing the power button without letting go, release the Stop Reset button. Hope it helps.

Dear, hello, I'm glad to answer for you, Canon printer warns E05 because of cartridge recognition failure, Canon printer shows E05, that is, it means that the ink cartridge cannot be recognized or is not compatible with tapping, or the ink cartridge is not installed correctly, it is recommended to clear or replace the ink cartridge to solve, and you need to replace the ink cartridge with a new one. The steps to solve the problem are as follows:1. Cause 1:

It may be because the cartridge is incompatible or cannot be recognized by the machine. Workaround: Need to replace the cartridge with a new one.

2. Reason 2: The installation method of the cartridge is incorrect. Workaround:

Remove the cartridge and install it the correct way. 3. Reason 3: It may be because of a software failure Solution:

Press the Stop reset button first, then press the power button to power on (don't let go); While pressing the power button without letting go, release the Stop Reset button. Hope it helps.

Since its establishment in 1937, Canon has globalized and expanded its distribution business to various fields after years of unremitting efforts.

Show this. Dear, the specific operation steps are as follows: 1. Select "Settings" program.

2. After entering the program, select "Advanced Settings". 3. After selecting "Advanced Settings", select "Print". 4. When the plug-in is not installed, the display is blank.

Plug-ins can be found in AppGallery**, search for HP Print Service plug-ins. 5. After installation, you can see the switch for printing the jack in the setting of Fu Chai Qi. 6. After it is turned on, it will automatically search for the printer and display it.

7. Select Add Printer. 8. After selecting the connection, the printer will display it and you can print. Hope it helps.

E05 refers to a Canon printer with an incorrect cartridge installation issue. Here are some possible workarounds:1

Make sure the ink cartridge is properly installed on the printer. Open the cartridge hatch of the printer and check that the cartridge is installed correctly. If the cartridges are loose, reinstall the cartridges and make sure they are firmly inserted.

2.If the cartridge is installed correctly but the problem persists, try replacing the cartridge. It may be because the cartridge has run out or there is some other malfunction that caused the error.

3.Clean the metal contact points of the printer cartridge and cartridge slots. Use a clean cloth or cotton swab to gently wipe the metal contact points to remove dust and dirt.

4.Restart the printer. Sometimes the printer will cause errors due to other failures, and restarting the printer can be used to clear the cache and reset the printer settings to resolve minor issues.

5.If none of the above methods work, you may need to contact Canon's after-sales service or professional technician to check the printer for further troubleshooting. Please note that E05 errors can be caused by a variety of factors, and the above methods are not guaranteed to work.

Summary. Reason 1: It may be because the cartridge is incompatible or cannot be recognized by the machine.

Workaround: Need to replace the cartridge with a new one. Canon printer shows e05 how to fix cause 2:

The cartridge was installed incorrectly. Solution: Remove the cartridge and install it in the correct way.

Canon printer shows e05 how to solve 3 reason 3: may be because of software failure solution: 1, first press the stop reset button, and then press the power button to power on (don't let go); While pressing the power button without letting go, release the Stop Reset button.

Reason 1: It may be because the cartridge is incompatible or cannot be recognized by the machine. Workaround:

A new cartridge needs to be replaced. Canon printer shows e05 should be bright how to solve the problem 2: the ink cartridge is installed in an incorrect way and the key is high.

Solution: Remove the cartridge and install it in the correct way. Canon printer shows e05 how to fix 3 reasons 3:

It may be because of the software failure solution: 1. Press the stop reset button first, and then press the power button to power on (don't let go); Press the power button and release the stop reset button at the same time as you let go.

Among Canon printers, there are many products with good performance configurations, and Canon IP8780 is one of the classics. The Canon IP8780 is a calm black color as a whole, and the body is particularly wide, which looks very atmospheric and elegant. The fuselage is surrounded by a black fine matte surface, while the two flap surfaces on the top of the fuselage are made of different materials.

When you move the Canon IP8780, you will experience a very different feel when you slip slowly.