Guess how much Parker wrap costs for this car? 100

The film should not only choose regular products, but also pay attention to the construction process of the car film. Because the effect of the film depends largely on the application process.

1. In order to avoid dust and impurities affecting the effect of the film, the body glass should be cleaned first before the car film.

2. The parts that may be damaged during the car film should be covered in advance to prevent scratching the car paint, interior and other parts; Accessories that may affect construction also need to be disassembled in advance.

3. After the overall treatment of the car body, it is necessary to start cutting the car film, and the car film should be preliminarily cut according to the size of the glass.

4. Paste the roughly cut car film on the car glass, and then the front and rear gears need to bake the film according to the amplitude of the car glass, and the effect is to make the amplitude of the car film close to the glass, so that the car film will be flat and free of water marks.

5. After baking, the film will be very obediently attached to the glass, and then it is necessary to make further corrections, that is, according to the shape of the glass, the corresponding shape will be finely cut.

6. The glass film is pasted inside, so the key step is to put on the film, and the requirement of the upper mold is to clean the inside of the glass, which is fast and accurate, and pushes out the moisture as soon as possible.

7. After all the work is done, the last need to do an inspection work, after the whole vehicle is pasted, the situation of each window should be checked, especially the corners, and the blistering phenomenon should be dealt with immediately.

Reminder: After the film, it is required that the window cannot be opened for 2-5 days, the rear gear cannot use the defogging function, and the front windshield cannot use the air conditioner to blow the air; Do not use toothed objects to scratch the glass; After the construction is completed, the warranty application form must be filled in, so that the after-sales service in the future can be guaranteed; After 3 days of car film, it is best to go back to the store for a re-inspection, and if there is any quality problem, it should be repaired in time.

Guess right, give a hint first.

Yes, it's just a concept car, not in production.

A Pikes Peak concept car worth 30 million euros (RMB 100 million) produced by Audi in Germany

Audi Parker, a German brand. The Audi Allroad Quattro, derived from the Audi A6, tried to fill this void, but unfortunately it failed to do so in the same way as the Regal Cross Country wagon. The real Audi SUV was launched in 2005 and is based on the Audi Pike Peak Quattro concept, either known as the Audi Q7 or the Audi Magellan, which towers proudly like the Pikes Peak at an altitude of 4,300 meters.

Fuji-ta's car is not very good, battle, but the car is very good-looking in English, much better than Giant.

The most expensive car in the display is a sports car, but it can't be driven on the road and is just a collector's item. The most expensive car you can drive on the road is now a Mercedes-Benz, and there is an all-** Mercedes-Benz in Dubai. It is possible that the Bugatti Veyron is the most expensive. I hope it will be adopted.

**First, Silver Charm second, Pikes Peak fourth, Bugatti sixth.

**Cart! However, it can't be driven on the road, and it will wear out 50g for every 100km driven**!! Made by an Arab!

The Audi Pikes Peak Quattro 8-cylinder twin-turbo FSI engine accelerates with strong traction capacity. It accelerates from 0 to 100 km/h in just 5 seconds (from zero to 60 mph in seconds) and has a maximum speed limit of 155 mph (250 km/h). A maximum torque of 630 Nm can be achieved at low rpm at 2000 rpm and peak torque can be maintained over a wide range of engine speeds.

Scarcity is expensive, but I think: this rotten car is not special at all! Rotten rotten car.

How can a car exceed 100 million, and it is still a concept car a few years ago, and the concept car is to show the future design style and trend of this brand car.

It's a concept car, it doesn't make sense to bid 1 billion, you think, hundreds of Germans made it with high wages, and it's not expensive to think about it.

The Audi Pikes Peak Quattro concept was unveiled in 2003. The impressive concept car is named after the 4,300-metre-high "mountain of the United States" Pikes Peak Ashiga, partly because Audi has won the Pikes Peak International Hill Climb three times in its history, but also because the Q-series model inspired by the Audi is suitable for all kinds of road conditions. The Audi Pikes Peak Concept is the first Audi car to use LED headlight technology.

The concept car's fog strip lights caused a global sensation. The strip-shaped headlights are not only aesthetically pleasing, they are extremely popular with the public; It is also very technologically efficient, and can significantly reduce the energy required for lighting. As a result, Audi became the first car manufacturer to realize the potential of LED lighting technology and integrate it into vehicle design.

The original picture is this, Harvard H2

**: 10,000 guide price: 10,000.

Displacement: Transmission: Manual Automatic.

Body structure: SUV fuel consumption: 7L