What should I do if there is a problem with Tengda wireless router, my WAN port status is always con

Continue to select "ADSL Virtual Dialing (PPPoE)", then enter the password of your broadband, next, save, and then connect, the IP address appears to indicate that the connection is up, provided that your broadband is normal, if the setting still does not work, then you try to restart the modem and router, and try again.

For the Tengda wireless router setting problem, before introducing how to set up the Tengda wireless router in detail, first let you understand the basic process of general Tengda wireless router settings, and then compare the advantages and disadvantages of the following methods.

How to set up a TENDA wireless router.

Tengda wireless router setup.

Select the left side: Tengda wireless router settings - next, continue to select "ADSL virtual dialing (PPPoe)", and then enter the password of your broadband, next, save, and then connect, the IP address appears to indicate that the connection is up, provided that your broadband is normal, if the setting is still not good, then you try to restart the cat and router.

The WAN port displays the troubleshooting method in the connection.

You don't need a router to try this first, if you can. It's a router setup problem. If it doesn't work, it's a problem with the network. Problems with the network %80

1 The WLAN port is not lit, it is not linked to the operator server, which means that there must be a wiring problem with the state.

2 You first pull out all the threads, and then, as I said, make sure to connect them in 2 minutes.

3 Find out the cable that can dial up the Internet directly, and if there is a cat, it is the network cable that comes out of the cat.

4 Then try this line, directly connect to the computer, dial up the book to sell the old network, you can get on it, this line is very important.

5 After finding it, connect this network cable to the router you want to use, and the color is different from the other four interfaces.

6 The router is connected to the computer, just choose one of the four interfaces with the same color, all the same, the interface must be connected first, if the excuse is not right, it is useless to configure it, everything is in vain.

7. After the interface is completed, enter the route, and there is a network service on the left side of the point, and there is a WLAN service in it.

8 Go in and select the PPPOE dialing method, and then enter the account password of the landlord's broadband on the lower bucket ridge surface, and automatically dial the number.

To enter the broadband account and password into the WAN interface of the router, click on the connection to see the IP parameters assigned by the operator. If it doesn't work, either the external network is wrong or the router is not configured.

It may be that your router IP and your computer IP conflict, and it is time to take a look at the IP of your routerIf your router IP is and your computer IP is, you can change your router IP to.

You have a cable plugged into the WAN port of the router. But is the other end of the line connected? The lights at the entrance of the wan are not on. It's either that your side isn't plugged in or the other side is disconnected.

Are you connected to the cable of the optical modem? Check if the line is good.

Whether the PPPoE dialing is set up correctly.

Problem 1: All WAN port parameters are 0 and the connection is in progress all the time, but the connection cannot be successfully (log in to the management interface of the router and click Running Status >> view the WAN port status).

Solution: 1. Check the line, if the line is connected correctly, but the WAN port indicator is not on, please check whether the WAN port wiring is in poor contact, etc., and try to replace the network cable connected to the WAN port;

2. Confirm that the account and password are entered correctly, click Running Status >> WAN port status on the management interface of the router, if the WAN port does not get the IP address, the page will have a reason prompt for dialing failure, modify it according to the prompt;

3. The broadband service provider binds the MAC address, connects the computer that was connected to the broadband Internet access separately with the LAN port of the router (here it must be connected by wire), and logs in to the management interface of the router. Select Network Parameters >> MAC address clone, click Clone MAC address. When the MAC address is the same as the MAC address of the current management PC, click Save and Restart the Router.

Hello! If your router cannot be connected to the network after it is set up, and the WAN port status shows "Connecting", please troubleshoot the problem by following the following steps:

The WAN port displays the troubleshooting method in the connection.

Owners spend networks where there should be dial-up, routed WAN ports set to automatic or dynamic IPs, and dial-up can be set.

If the WAN port of the Tengda router is not connected, the WAN port of the router has not detected the signal, and the fault only lies in the WAN port of the router, the Ethernet port of the uplink device (here the optical modem is taken as an example, that is, the Ethernet port of the optical modem), and the network cable between the two.

1. First of all, change the router port to determine whether the router port is broken;

2. Change the network cable or use the line tester to test the network cable on/off, check the quality of the crystal head, and eliminate the network cable fault;

3. Replace the network card or computer to test whether the network card is broken.

After the above three steps, you can basically eliminate the failure of the WAN port that is not connected.

First of all, the fact that the reset light is fully on does not prove that the route is good or bad.

Let's rule them out one by one.

1. Try to change the network cable, and replace the connected port.

2. One end of the network cable is connected to the WAN port, and the other end is connected to the computer.

Before, I was able to connect directly to the Internet port behind the computer?

Okay, first of all, what kind of Internet access do you have, do you connect to someone else's router?

First question:

1) First of all, I can't find the icon for "wireless connection" in my network neighbors?

Did you read it on a desktop? Your desktop only has a wired network card, which is Broadcom BCM440X 100Base-TX FastEthernet Lenovo, of course, there will be no "wireless connection" icon, you need to install a wireless network card, and install the driver correctly, and the "wireless connection" will appear

2) The connection status of the WAN port on the upper port is always connected (in fact, it is not connected).

Is your router set up correctly? You first provide your connection method, whether it is PPPoE, or pull the cable from the switch, or pull the cable from someone else's router, and whether the IP on the computer is automatically obtained or manually set when surfing the Internet, you have to make it clear.

Hypothetical question:

If the network cable at home is obtained from someone else's router, is it impossible to connect to another wireless router?

This doesn't affect at all, if that's the case, you can still take it. This is a cascading problem with routers. There are two ways to connect.

Ask questions!

Your Internet connection is not right Ask your broadband access provider, the wireless settings are not found in the management interface of the router computer system, and there are many specific ways to enter the Internet.

If you connect from someone else's router, you can go directly to the Internet, you can connect to a wireless router, and the WAN connection method should choose a fixed IP

1. I don't see the steps you took to set up your router.

2. If it is a cable pulled from another router, you can directly check the LAN port of your router, and the desktop can also check the LAN port, and you can use it without setting up the router.

3. There is no driver of wireless network card in the driver.

The first problem is that you don't have a wireless card acceptor so the desktop won't show it, and the second problem is that you have to make sure that the network cable on your wall is a bus.

First of all, make sure whether you want to dial in the account and password when you go online, if so, set it to PPPOE mode in the routing path, and enter your original account and password, if not, select dynamic IP mode.

1 Check whether the security settings are correct according to the instruction manual, and 2 Check whether the settings of the network card match the router.

3 Restart your router.

4. The IP address of the router is automatically assigned, check whether the NIC address has been obtained. Check if the network cable or ping router address is correct if you don't get it.

Hello! Make sure that you have selected the correct way to access the Internet. ADSL dial-up: If you need to click on the broadband connection to access the Internet (when you are not connected to the router), you should choose the Internet access method if you can access the Internet only after successful dial-up.

Hello! Check if the router has a WAN IP address, then check if the computer has an IP address, and if so, check if the DNS server is set up incorrectly! Hope the answer helps! Have a great day.

Ask the password settings of the Tengda router, 1After the WAN port is not connected to the modem gigabit port, after the WAN is connected to the modem gigabit port, the mobile phone enters the password and has a wifi signal, but the WAN port cannot be used.

Broadband dialing. Dynamic IP

Static IP Question 2: Connect the WAN port to the Gigabit port of the optical modem to automatically obtain the IP address, and a prompt appears that the system detects that it is a static IP

Hello Answer! After the broadband service is activated, the operator does not provide you with any Internet access parameters. When you are not using the router, you only need to plug the broadband network cable into the computer, and the computer will automatically access the Internet. In this case, under the WAN port setting option of Tengda router, you should select:

Dynamic IP (automatically obtained).

Hello! Sometimes the route automatically detected by the router may not be accurate.

Hello! When broadband is activated, the operator provides the IP address, subnet mask, default gateway, preferred DNS, and alternate DNS information for Internet access. When the router is not in use, you need to fill in the IP address, subnet mask, default gateway and DNS server address information provided by the operator in the local connection of the computer, and then the computer can access the Internet.

In this case, under the WAN port setting option of Tengda router, you should select: static IP

Ask whether the modem and the router are in conflict in the above case.

Hello Answer! After selecting the Internet access mode (networking mode) of Tengda router: static IP, you need to fill in the IP address, subnet mask, gateway, and DNS server address provided by the broadband operator on the page.

Hello! There is a conflict that can turn off the wireless network of the fiber modem and only use the wireless network of the wireless router.

Question: Static IP is not something that most people want to use.

Static IP is not only set up with a complicated lock, if it can be set successfully, what is the difference between dynamic IP and static IP in terms of effect?

Hello Answer! The difference between dynamic IP and static IP is that dynamic IP needs to automatically obtain an IP address when connecting to the network for users to surf the Internet normally, while static IP is the IP address assigned to the user by the ISP at the time of installation, and can be directly connected to the Internet without obtaining an IP address.

Dynamic IP: Because IP address resources are very valuable, most users use dynamic IP addresses to surf the Internet, such as computers that access the Internet through modem, ISDN, ADSL, wired broadband, cell broadband, etc., are temporarily assigned an IP address every time they go online. Static IP:

Generally, it is a special server or a computer that uses a dedicated line to access the Internet to have a fixed IP address, and it is more expensive.