How to bridge a wireless router with telecom cat ZXV10 H618C

Hello:Configuration steps:

First, the configuration of the cat:

1. Type " in the address bar, and then in the pop-up window, 2. In the WAN port settings, set the current Internet access mode, in this case PPPoE dialing.

3. Set the basic information of the wireless, change the default SSID to AP1, enable the bridge function, and enter the wireless MAC address of AP2 in the box below.

4. Keep DHCP enabled.

2. Router, configuration diagram:

2. In the LAN port settings, change the LAN port IP to :, and then click "Save".

3. The WAN port setting remains the default and unchanged.

4. In the basic settings of "Wireless Parameters", change the SSID to AP2, enable the Bridge function, and fill in the MAC address of AP1 in the box below.

5. In the DHCP service settings, disable the DHCP service. Then click "Save".

The basic configuration of point-to-point wireless bridging is complete. With the wireless client, you can surf the Internet normally whether you are connected to AP1 or AP2!

Dear Telecom Broadband users, a new connection.

Carrying services on the Internet (enabled).

Mode route (PPPoE).

Use NAT to enter your account and password for surfing the Internet.

Sure hope it helps, and I wish you a great day!

Equipped with broadband, Internet room! Guangdong Telecom's online business hall is equipped with telecom broadband, faster, easier and more economical! 4M pure telecom broadband, no fixed line and mobile phone, one household and one line, no peak pressure on network speed, please click for details.

OK. After cracking, just connect to radio and television broadband. Cracking can be done on the ** to pay people to crack it remotely. Just tell them that they are connected to radio and television broadband.

Is the router of the telecom wireless、、、 carefully read the setup manual.

I'm sorry, this router is a combination of modem and router, so it uses a telecom signal, and the signal used by radio and television is different from that of telecommunications, so it can't be used!

Yes, it's the same as telecommunications.

How to configure wireless Internet access on a wireless router:

1.Connect the wireless router to a higher-level network device (e.g., modem, first-level router).

Connect the WAN port of the router with the LAN port of the higher-level network device with a network cable, and the connection is successful when the WAN port light flashes on the router.

2.Connect your computer wirelessly to your router.

The computer searches for the router's wifi name (the default wifi name is located on the nameplate on the back of the router) and connects to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the wireless gateway configuration page.

Open a browser, enter the IP address of the router gateway (usually, the default value is located on the nameplate on the back of the router) to enter the gateway configuration page. (This interface will pop up automatically for new routes).

4.Set up a wireless router to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and wifi password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key.

6.After the setting is completed, the router will automatically restart, please enter the new wifi password to connect, and you can access the network.

Hello,The wireless cat sent by Telecom does not have the routing function turned on,You have to dial in after connecting to the wireless signal to use,It is recommended to buy a wireless router and install it。

That's not a router, that's a telecom cat. If you want to use wireless Internet yourself, you have to buy a wireless router. I've provided ** to you, just follow the steps explained above to set it up, don't forget to adopt it.

Crack it directly. Create a new connection, and you're good to go with a simple setup.

Dear telecom users, first of all, please enter the default address into the browser, and then enter the default account password of the router, usually admin, and then you can operate according to the manual, of course, if there is no manual, you can click to enter the setting wizard of the page, step by step to complete the operation;

Hope the above helps!

If you have any other questions, please come to the platform or the official website of Anhui Telecom.

Not to mention that your method of setting up is complicated and simply cannot be implemented, you have two methods1Turn on the routing function of the cat, you can call the customer service to arrange for you to complete the setup, you can use it as a wireless router, and all devices are connected and used without problems.

2.Buy a wireless router for use by yourself, and set it up according to the instructions for use, and it is not difficult to operate. You can also use multiple devices to access the Internet at the same time.

Anhui Telecom Online Business Hall from October 10th to October 18th will join hands with major e-commerce companies to create a network-wide gathering, peerless and good price, not to be missed!

If you still have questions, please keep asking. Have a great day, thank you!

In that case, it's not very easy to get it, unless you go into the cat backend and use the routing function instead of the bridging function, or the phone will not be able to dial.