How to remove the washbasin faucet, and how to change the faucet on the washbasin?

1.Before replacing the faucet, turn off the main water valve in your home, turn on the faucet, and drain all the water inside. You can first remove the water inlet pipe, which is connected to the angle valve.

With a wrench, the hose can be easily removed by holding the hose with one hand and turning the wrench with the other.

2.Next, remove the fastener, one of the nuts is already locked, you can also use pliers or a wrench to unscrew it, and finally remove the whole faucet.

3.Install the new faucet, remove the fixed base, rotate the nut out of the pipe, thread the hose, connect with the angle valve, and tighten. Then install the handle position of the faucet, fix it first, and if there is no problem, tighten the nut again.

Faucet is a popular name for a water valve, which is used to control the size of the water flow and has the effect of saving water. The replacement speed of faucets is very fast, from the old-fashioned cast iron process to the electroplating knob type, and then to the stainless steel single-temperature single-control faucet, stainless steel dual-temperature double-control faucet, kitchen semi-automatic faucet. Nowadays, more and more consumers will consider the material, function, shape and other aspects of faucets.

There are many types of faucets, the most common one is that there are two 8 screws on both sides of the faucet, there are long rods and bucket boards, and they are sold in the hardware market, and I bought them for 8 yuan.

There is also a large screw with the same thickness as the faucet, I don't know if yours is in these two cases.

Because the location of the sink installation faucet is very deep, it is best to use a special tool - a socket wrench.

Turn off the main gate in your home first, unscrew the old faucet, and install the new one.

First of all, turn off the main water gate of the house. The purpose is to ensure that there will be no splashing during the process of dismantling and replacing the faucet, which will cause unnecessary trouble.

After closing the sluice, wait a few minutes to make sure the remaining water in the faucet is completely drained before proceeding with the follow-up operation, or take a discarded towel to absorb the water to reduce the waiting time.

Use a knife to pry open the protective sheet on the faucet handle, this protective sheet is just glued on, and it is easy to pry.

Select a screwdriver of the corresponding model (slotted mouth, cross mouth, etc.) to unscrew the screws of the faucet handle. Remove the faucet, because the faucet handle is fixed with occlusal tooth patterns, so the disassembly process requires a little force.

Open the bottom hinge, the disassembly work is completed, and the relevant tools should be sorted out in time.

Install the new faucet with the reverse steps above.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

Washbasin faucet disassembly method:

1. If you want to remove the washbasin faucet, you should first find the inlet valve of the washbasin, and the inlet valve is generally installed on the wall under the washbasin. Before disassembling the washbasin faucet, the angle valve should be screwed up first, so that the water source of the washbasin faucet is cut off, so as to avoid a large amount of water flowing out of the faucet in the process of disassembling the washbasin faucet, resulting in a waste of water resources.

2. After the angle valve is screwed on, there will generally be some water left in the water pipe of the washbasin, so it is also necessary to open the washbasin faucet to discharge water, until there is no water and then flow out of the washbasin faucet.

3. In the process of installing the washbasin faucet, it is generally necessary to use the water inlet hose to connect the water inlet and angle valve of the washbasin faucet together, so when disassembling the washbasin faucet, one hand should hold the water pipe of the washbasin, and the other hand should twist the wrench at the same time to remove the end of the connection between the water inlet hose and the washbasin faucet.

4. In the process of installing the washbasin faucet, when the inlet hose is connected, it is generally necessary to use a fastening nut to lock the inlet hose, so when disassembling the washbasin faucet, you should first find the fasteners of the washbasin faucet, and then use pliers or a wrench to unscrew the fasteners, and then you can disassemble the washbasin faucet.

5. When disassembling the washbasin faucet, if the inlet hose is brittle, or the fasteners are rusty, then it is generally difficult to easily disassemble the inlet hose, so you should first drop some oil on the rusty position, and then take out the washbasin faucet.

Precautions for disassembling the basin faucet:

1. The hose under the faucet of some family basins is very deep in the pipe, and it takes a certain amount of effort to disassemble. This is because the spool seat may be screwed onto the faucet body at the time of installation. You can use a relatively long screwdriver to unscrew the screws counterclockwise from the bottom, and then push out the spool seat and high-pressure hose from the bottom up.

2. Some water inlet hoses have been used for a long time, and the water inlet hose cannot be unscrewed for a while due to embrittlement or rusty fasteners, and the basin faucet can be taken out after two or three drops of oil are dripped on the rusty parts.

Turn off the water source: Before disassembling the faucet, you need to turn off the water source first to avoid unnecessary trouble caused by the water flow.

Remove the old faucet: Use a wrench or a wrench to pull the screws of the faucet to remove the faucet from the sink.

Clean the dishwasher: There may be some dirt under the removed faucet that needs to be cleaned.

Install a new faucet: Insert the new faucet into the hole in the sink and tighten the screws with a wrench to make sure the faucet is secure.

Connect the water pipe: Connect the water pipe to the faucet, then tighten the nut with a wrench to make sure the water pipe is tightly connected to the faucet.

Turn on the water source: After the installation is completed, turn on the water source, check whether the faucet is leaking, if there is a leakage of water, you need to re-tighten the screws or replace the sealing gasket.

The tutorial for disassembling and assembling the sink faucet is as follows:

1. How to dismantle the sink faucet:

1. Preliminary preparation: turn off the water inlet valve, or use other faucets to divide the pressure.

2. Disassemble the faucet: separate the inlet water and the hose dust, and twist it with a wrench.

3. Separate the faucet and basin: remove the fixed device, due to the age, you need to pay attention to the brittleness of the hose.

4. Sawing the interface: Because the glass glue is fixed, sawing is a good method.

2. Precautions for faucet installation:

1. Before installation, you need to check the integrity and integrity of the accessories, first check whether the basin and downspout are flat, and replace them if there is a problem.

2. When making connections, we must consider the tightness. When installing a short falling water, a rubber gasket is placed on the top and bottom, and it is strictly forbidden to use silicone as a cushion. The fixing screw should not be tightened too tightly, otherwise it is easy to cause the deformation of the cushion.

3. The faucet is metal, and the basin is ceramic, and if there is long-term friction between the two, it is easy to wear and tear, so rubber or plastic gaskets should be applied between the faucet and the basin to prevent hard contact and damage to the basin.

4. For the three-dimensional faucet wash basin, it is particularly easy to install crookedly, which affects the overall appearance, so you can try to install and locate it several times to find the most central position.

5. After installation, it's not over. We also need to do a closed water test to see if there will be overflow, and if so, we will make adjustments.

History:

Before the advent of faucets, the walls of the water supply springs were inlaid with a kind of animal-headed, usually stone-shaped, and a few "flowing water mouths" made of metal, from which the water flowed was always a long, uncontrolled stream. In order to avoid wasting water and to solve the growing shortage of water resources, faucets were developed.

The original faucets were cast in bronze, and later switched to cheaper brass. Some faucets are simply simple and practical, while others are very decorative.

The faucets of various shapes, such as snakes, dragons, rams' heads, geometric shapes or flower shapes, reflect the architectural decoration of the era. The faucets of the court and other important buildings were mostly made of silver, silver alloy or bronze gilded, photographed and intricately carved.

Kiss Glad to answer for you: What tool is used to disassemble the sink faucet Answer: Kiss Washbasin hot and cold water faucet drainer installation fastening, disassembly, maintenance, replacement socket wrench tool.

What is the disassembly method of toilet basin faucet? Step 1: Prepare the tools first:

Screwdrivers, wrenches, pliers. If it's just a replacement part (e.g. a seal), then have this part ready. Then close the main valve.

Step 2: Remove the small screws on or behind the faucet handle and remove the handle that is fixed to the faucet body. Some faucet screws are hidden under metal buttons, plastic buttons or plastic sheets, and as long as you open the button, you will see the handle screws installed on the top.

The screws of a faucet that have been used for a long time may become very tight due to rust and other reasons, and some lubricating oil can be dripped into it. Step 3: If the screw is hidden in the hole, it is recommended to observe it with a flashlight first, mainly to see what the fixing screw inside is, the cross or the word, and then use the corresponding screwdriver to loosen it.

This screw of a few brands of faucets is an inner square hole (such as Moen), which is more troublesome to remove, and special care should be taken not to damage the screw mouth when using alternative tools. When the screw is released, the handle can be removed. Remove the faucet handle Step 4:

At this time, you see a large copper nut, after removing the nut with a large movable wrench, you can remove the valve core of the faucet, thank you for your patience. The above is my full reply, if you are satisfied with my service, please give a thumbs up, and I wish you all the best! Peace and joy!