What is the problem with the dehydration standard light of the WEINIG washing machine?

The washing machine spin bucket has a soft indicator light for the following reasons.

First of all, check whether the line of the indicator light is shorted?

Secondly, you can turn the machine off and turn it back on again to see if there is still such a fault, if there is such a fault, it means that there is a problem with the circuit board.

Hello, there are many ways to choose from in the washing machine, and the standard soft light on means that you have chosen the gentle mode for dehydration.

This dragging problem is so bright, then the belt is loose or the pulley has a hook or it is off, you can open it to see some of the conditions behind.

If the soft light is on, it means that the dehydration system is coming to an end, giving you a hint.

That means your WEINIG washing machine's circuit is faulty. You can call the after-sales service of the low-profit attack** to repair.

The dehydration standard of the Weinig washing machine is soft and the light is on, and there should be no problem with the light on, because when the washing machine is working, he will also show that the light is on.

If the light is on in the washing machine, it should just choose this mode, so there will be this reminder, and then it will have this bright word.

The WEINIG washing machine is dehydrated according to the standard, and the soft light is on, which may be a circuit fault.

What is the problem with the dehydration standard Qin Niu light on the Weinig washing machine? It's just not enough pressure.

What is the problem with the standard light light on the dehydration standard of the vertical washing machine? That's because you're setting a gentle standard of strength when you're dehydrating.

Hello, the washing machine washing light and spin light flashing should be a fault signal before turning into spinning after washing, which refers to the draining timeout. It is recommended that you check whether your drainage system is blocked (lift the drain pipe to check if the drainage is relatively small) spike pants, if so, then deal with it as follows: Drain valve foreign body treatment:

Open the back cover, find the drain retractor, pull the retractor by hand, drain the water, and then say. After draining the water pull, put down the washing machine and find the drain tractor, the bottom of the barrel is connected to the tractor, there is a cover to twist it by hand, and if you can't twist it by hand, you can use a flathead screwdriver and a hammer to knock it open in the counterclockwise direction, it should be loose, and it should be loosened. Pull.

The leather plug inside, use your fingers to hook the valve core, you will feel that there is a foreign body in the Ming family, and it is OK to take it out.

1.Whether the laundry is heavily on the side of the dehydration bucket, or if there is too much clothing for the dehydration bucket to function.

2.The plug of the closed door switch is not connected to the rubber bridge, and it is more likely that the connector and the guide beam are normal --- the wire.

3.Check for foreign objects between the stocking dehydration bucket and the bucket.

4.If the V-belt is too loose or falls off, the belt can be adjusted or replaced.

5.The large oil seal was not properly installed and jammed the dehydration shaft. (Generally, it is easy to occur after replacing the large oil seal during maintenance) 6The brake band is not loosened.

7.The program control board is faulty.

The dehydration display of the weinig washing machine is 11 Hello dear, ** is the abnormal water ingress, Bu Jian water inlet did not reach the set water level for 20 minutes. Solution: 1. Check whether the inlet valve is normal.

2. Check whether the pump and computer board are working normally. 3. Please check whether the inlet water pressure is too small, it is recommended to use it when the water pressure is stable. 4. Please unscrew the water inlet pipe from the washing machine, check the filter screen of the water inlet valve to see if there is any debris blockage, and use a small brush (such as a toothbrush) to clean the filter screen at the valve port of the water inlet pipe.

I hope it can help you, if my answer is helpful to you, please give a like (in the lower left corner of the evaluation), look forward to your like, your efforts are very important to me, and your support is also my progress. Finally, I wish you good health and a good mood!