What is the reason why the Haier washing machine suddenly cannot be dehydrated?

Generally, the circuit board and motherboard are faulty, and after-sales testing is required to replace the motherboard with a new one.

What is the reason why the washing machine is not dehydrated, look at the detailed explanation of the maintenance master, and figure it out in 4 minutes.

1. Foreign objects are wrapped around the bottom of the outer wall of the dehydration tank.

When the dehydration bucket rotates at high speed, the small thing will throw the gap between the top of the dehydration bucket and the end cover into the bottom of the outer wall of the dehydration bucket, and then tightly wrap it around the shaft between the bottom and the water seal, so that the motor cannot run and cause dehydration.

2. Capacitor failure.

After the power supply of the washing machine, the motor of the dehydration bucket makes a "buzzing" sound without turning, at this time, you can unplug the power plug, check whether the capacitor is invalid, or replace it with a new product; If the motor starts running normally, the fault is on the capacitor.

3. The shaft sleeve and shaft of the dehydration motor are locked.

After the washing machine is energized and started, the shaft drives the shaft sleeve to form friction between the sleeve bowl and the sleeve tablet, which will make the dewatering bucket motor rotate slowly or cannot be started. At this time, the shaft failure needs to be taken out and repaired, and the fault can be eliminated after reassembly.

4. Dehydration motor failure.

Failures such as coil burnout and wire disconnection of the dehydration motor of the washing machine will cause it to fail to work properly. The damage of the motor coil is mainly due to moisture, mostly caused by the damage of the water sealing bowl or the serious wear of the shaft sleeve that causes water to leak into the motor coil. For this kind of failure, the water seal must be checked, and if it is found that the water seal is damaged or the water seal sleeve is seriously worn, it should be replaced one by one.

Pro, the reasons are as follows: 1. The problem is mostly in the water level detection switch, due to the poor contact caused by oxidation, dirt or ablation of the contact, the power supply can not be turned on, causing the water ingress, at this time, the water level switch should be overhauled or replaced by the cavity. 2. If the pressure pipe is worn and cracked due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle or disconnected, causing air leakage, it can also lead to more than water ingress, because the computer board is not under pressure and the water level switch does not work, and the water is not yet cleared, at this time, the pressure pipe should be checked for wear and whether there is contact between the two joints.

3. Due to the long use time, there is a foreign body blocking the air valve mouth, resulting in the pressure can not be transmitted to the pressure switch, at this time the big nut should be unscrewed, and then take out the inner barrel to take out the foreign body blocking the air noveil. 4. The valve core of the water inlet valve is stuck, resulting in the inability to reset, resulting in the washing machine being flooded, and the water inlet valve should be overhauled or replaced. 5. If everything is invalid, you should try to replace the computer board, because all actions are controlled by the computer board.

What to do if the washing machine can't be dehydrated.

1.The washing product is in a state of non-dry and closed equilibrium when washing. When there is too much laundry, the washing can not be adjusted to the balance, then the washing machine will automatically adjust to a low speed resulting in poor dehydration effect, if this is the reason why the washing machine can not be dehydrated, then don't worry too much:

You can put less clothes before washing them, and don't stuff too much at once, so as not to cause an imbalance during washing. And the effect of dehydration is not good.

2.The safety switch on the top cover of the washing machine is damaged. The process of dewatering the washing machine is a mechanical movement that operates at high speed.

Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch, if the top cover linkage switch of the washing machine is damaged, the washing machine can not be dehydrated. Warm reminder: to avoid causing the washing machine to not crack and cannot be dehydrated, do not open the top cover during the dehydration process of the washing machine.

3.caused by the texture of the clothing. Compared with summer, there are many types of clothes in winter, such as tweed type of clothes with strong water absorption, if you choose low-speed dehydration, it will cause the illusion that the washing machine can not be dehydrated, so it is recommended to use high-speed dehydration (ps:

High-end clothing cannot be dehydrated at high speed).

4.The washing machine drain system is clogged. When the drainage system of the washing machine is blocked, the washing liquid in the water cylinder can not be discharged, when there is too much foam in the water cylinder, or the washing liquid in the cylinder is difficult to drain for a while, the water level switch can not be reset, and the washing machine cannot enter the dehydration program.

If the washing machine cannot be dehydrated due to this reason, it is recommended to remove the drain filter for cleaning, rinse the drain with water and remove the debris in the drain valve.

5.The water level switch cannot be reset. The washing machine dehydration process starts with the water level switch reset after the washing liquid has been drained.

If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after the drain is completed, and if the water level switch is damaged, you will not be able to enter the dewatering process! Solution: Contact the after-sales point.

<> the drain is in the wrong position. When the washing machine drain pipe is placed too high, and the drain pipe cannot be drained normally, the washing machine will not be dehydrated, and the washing machine drain pipe should be placed on the ground to drain the drain, if it is placed too high, it will not be able to drain the water.

Another situation is that the drain pipe of the stool banquet is blocked, when the drain pipe is blocked, it will also lead to abnormal dehydration of the washing machine, when the drain pipe can not drain normally or the outlet of the drain pipe is placed in the water, it is easy to cause abnormal drainage.

There may be several reasons why Haier washing machines cannot be dehydrated:

1.Water level issues: If the water level of the washing machine is higher than the stated maximum water level, then the washing machine may not be able to dehydrate. At this point, it is necessary to argue that some excess water should be drained or the power of the washing machine should be re-selected.

2.Speed problem: Some washing machines need to set the appropriate speed in the spinning program, if the selected speed is not suitable, it may also cause the washing machine to fail to spin.

3.Machine problems: A malfunction of the washing machine's control panel, sensors or motor can also prevent the washing machine from dehydrating.

4.Fitting failure: Due to aging or damage to parts, such as electronic pulse valves, fans, low-pressure switches, etc., it may cause the washing machine to fail to dehydrate.

5.Laundry problems: Laundry that is too wet or overweight can also cause the washing machine to not dehydrate.

6.Plumbing problems: If the pipes are blocked or the water pressure is insufficient, it can also affect the normal operation of the washing machine.

For the above problems, we can inspect, repair or replace the corresponding parts to solve the problem. If none of the above methods can be solved, it is recommended to contact professional maintenance personnel for troubleshooting.

<> this situation may be yoursThe washing machine panel is not properly closed, or the switch is not in good contact；It could also be a washing machineThe water level switch is not reset, probably at the time of washingToo much foam or clogged drains；There could also beThere are more clothes that are unbalanced when placedcaused. Here's a closer look:

1. It may be that the panel door of the washing machine is not closed well or the switch of the top cover is damaged, or it may be that the switch is in poor contact, because the washing machine is a high-speed action when dehydrating, and the top cover is not allowed to be opened, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened, check whether the top cover is covered, or it may be that the top cover sensor is faulty and needs to be replaced;

2. It may be caused by the blockage of the drainage system of the washing machine or the bad drain valve, and the washing liquid in the water cylinder cannot be discharged. You can remove the drain filter and clean it, flush the drain with water and remove the debris in the drain valve, and dredge the drain pipe.

Or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program, so you can wait until the foam is discharged to enter the dehydration process;

3. The drain valve does not open the clutch conversion, and if the solenoid valve is damaged, it will make the dehydration unable to operate normally;

You can turn off the power for 2-5 minutes, try to re-power it, if it still can't be solved, you have to ask a professional maintenance worker to repair it.

4. When the washing machine cannot be adjusted to balance, the washing machine will automatically set a low speed or even stop the dehydration process.

You can put a small amount of clothes before washing the eraser, and do not stuff too much at once, so as not to cause imbalance during washing. And the effect of dehydration is not good.

Hope it helps!

When it comes to washing machines, everyone is more familiar with them than the waiters, which can not only wash clothes, but also have the function of spinning dry. There are many brands of washing machines on the market, among which Haier washing machines are well-known. However, some friends have reported that there will be no dehydration in use.

Most washing machines do not dehydrate for similar reasons, such as debris or damage in the drain pump; Caused by loosening or short circuit of the power supply line; The washing machine shows that the motherboard is faulty, such as no device is burned, etc.; If the upper cover is in poor contact with the travel switch or the clothes are not flat, the washing machine will not be dehydrated.

What are the brands of potato reeds for washing machines:

1. Haier. Haier was founded in 1984, starting with the production of refrigerators, after more than 30 years of development, its products cover a wide range of household appliances, including refrigerators, water heaters, washing machines and air conditioners, with excellent quality and well-known gas, Haier brand has become a leading brand of domestic home appliances.

2. Siemens.

Founded in Germany in 1926, Siemens has a long history in the industry. It mainly has the research and development, production and sales of household appliances. Its products are not only beautiful in appearance, but also excellent in quality, and are currently distributed in more than 40 countries and regions around the world, and are well received.

3. Beauty. Midea was established in 1958, mainly engaged in washing machines and other home appliances electronics manufacturers, with mature production technology and exquisite craftsmanship, Midea electrical appliances have won a variety of national patent awards, Midea is still constantly innovating, is committed to creating a more comfortable home space for consumers.

4. Panasonic. Panasonic was founded in Japan in 1918, mainly engaged in the manufacture of various electrical products, a wide range of products, covering home appliances, digital electronics, office and aviation and other fields, in 1987 Panasonic and the domestic factory set up the first joint factory, and continue to expand the scope of business.

Summary: The above is the reason why Haier washing machines cannot be dehydrated and what brands of washing machines are related to the content, I hope to help friends in need, if you need to learn more about related knowledge in the future, welcome to pay attention to Qeeka Home.

There may be a variety of reasons why Haier washing machines cannot be dehydrated, and the following are a few common faults and troubleshooting methods for users' reference.

The washing drum does not rotate: If the washing machine cannot rotate normally, the dehydration will not be able to do so properly. At this time, the user can first check whether the problem is caused by poor contact of the power plug; If the power supply is correct, you can disassemble the washing machine to check whether the transmission parts, motors, belts and other parts inside it are damaged or rusted.

There is a problem with the dehydrator itself: if the washing machine turns but does not spin, it is most likely that the dehydrator itself is malfunctioning. For example, the dehydrator drive belt breakage, bearing aging or loss of leaf spring elasticity can all lead to poor dehydration of jujube pin pants.

At this point, you need to find a professional maintenance person or replace it with new parts to solve the problem.

Water level control failure: In some automatic washing machines, the stool water level controller is one of the important components to control dewatering. If the water level controller fails, it can lead to insufficient or exceeding the standard, which can affect the dewatering effect.

At this time, it is necessary to find a professional maintenance personnel to inspect and replace the controller circuit board.

Clogged filter or drain pipe: If the washing machine dehydrates once when washing the laundry items, it can be dehydrated normally; However, if it does not dehydrate properly after a few repetitions, it may be the cause of a clogged filter or drain. Users can clean filters and drains themselves, or have maintenance personnel clean up sediment and foreign matter.

In short, there may be many reasons why Haier washing machines cannot be dehydrated, and they need to be investigated one by one. It is recommended that users carefully read the manual before use, and operate in accordance with the operation method in the manual to avoid damage caused by misuse. If there is a similar problem, please contact the manufacturer or professional after-sales service personnel for maintenance in time.

<> Reasons why Haier washing machines do not spin up: first.

1. The switch of the top cover is damaged. There is a linkage switch on the top cover of the washing machine, which automatically disconnects when the lid circuit is opened. Clause.

Second, the drainage level switch is damaged. Dewatering is a procedure that needs to be carried out after the draining is completed, and if the water level switch is damaged, the dewatering process will not be accessible. Clause.

3. The solenoid valve is damaged. Clause.

Fourth, the computer control board is faulty.

Common sense of washing machine maintenance:

1. After each washing, the stagnant water in the Guanhuai Wudao should be discharged in time.

Second, to prevent mechanical damage, do not force the drainage pipe, in addition to keep the drainage pipe clean.

3. It is best not to place the washing machine in a humid bathroom, otherwise the shell is more likely to age.

This answer is suitable for Haier dust EG10014B39GU1 drum washing machine.