How to fully detect the wireless router and how to check whether the router is working properly

Wireless routing detection is mainly to check the stability of the network, and then connect the wireless routing test without using a wireless router to test the stability of the Internet, and it is best to use a laptop or desktop computer to plug in a wireless receiver to test the situation.

Action: Start - Run - Enter "cmd" - Command appears and then ping

Detect problems with your computer and local router Boot · Run cmd Input: ping -t (the address may depend on the router), if the intranet is not normal, please try to delete the network card, reinstall the network card driver, or reset the router configuration!

The second step is to detect whether the external network is usual, such as the first step, ping -t, this IP is from Sichuan Telecom, I just give an example to see if it can be unblocked. If it is not smooth, restore the default configuration of routing, and check whether the operator's account password is incorrect, and consult the operator for details. If it is smooth as shown in the picture!

In addition, if the first and second steps fail, with the help of 360 security guard, do network configuration screening, or contact 360 free network engineers for one-on-one answers, it is also possible!

Hope it can help you, the word is too slow to type, and it is not easy to type.

Different routers, you can see the indicator light; And connect to wifi to use viewing.

1. If you connect to wifi, you can surf the Internet normally, that is, the router is working normally.

2. If you can't access the Internet, and the router management interface is dial-up and there is a network IP, it is a problem of arrears or business failure.

3. If the WAN does not light up (does not flash) in the indicator light, the optical modem.

The network cable of the hidden device must be replaced.

4. If there is a desktop computer connected to the back of the router, the corresponding LAN will be on (some new routers have only one light, you can see the corresponding LAN port indicator).

Just see if the indicator light is normal.

Here are a few steps to determine that there is a high probability that there is a problem with your router:

First of all, check the router settings and network settings, mainly the IP and DNS address are set to different IPs; If you are sure that there is no problem with your settings, call the customer service of the network operator** to check whether the network in the home is unblocked; Directly use the modem to connect to the Internet and check whether the network is unblocked. Plug the other end of the network cable plugged into the WAN port of the router and try to connect to the Internet with a computer. In addition, you can also use another network cable connection without problems to determine whether there is a problem with the original network cable; Observe whether the light corresponding to the LAN port plugged into the network cable connected by the computer host and router is always on, if not, it means that the network between the two is unblocked.

Introduction: Sometimes after passing through the wireless router, you can't access the Internet normally, and you can't tell whether it is a computer problem or a wireless router setting problem. Below I have sorted out for you how to check the router settings, I hope it will help you!

How to check your router settings

The wireless router is very easy to set up, as long as you log in to the wireless router, click on the setup wizard to enter the password, and the next step is to confirm that the stool can be completed.

One of the disadvantages of wireless routers is that they cannot recognize 678 or 691 errors, and they need to analyze them by themselves through their running status.

Click on the running status on the left, whether you can access the Internet at a glance, first of all, we look at the WAN port status, we can get the IP address and the correct DNS, indicating that there is no problem.

As long as you can connect to the wireless network, the automatically obtained address range is normal'。

One of the most important places is whether the WAN port data packet is generated by the old judgment travel data, if the connection fails, then there is no data generated. If the data refresh does not respond, it may be that the data refresh interval is not that short. If there is data generated, the connection is normal, and if the data is refreshed after a while, the network connection is normal.

That's the problem with the settings on your computer.

Wireless router setup signal stabilization method: To avoid interference and overlap of infinite signals, these three channels should be used in turn.

Details:1Although there can be 13 channels in a wireless network in a network standard, there are only three non-overlapping channels, that is, channels that do not interfere with each other.

Channel 3 interferes with channel 1 6, channel 9 interferes with channel 6 13, etc., so to ensure the stable operation of multiple wireless networks in the same coverage area, it is recommended to use (or 13) these three channels. If there are three wireless networks in the office, they should use each of these three channels in order to avoid interference and overlap.

2.For wireless routers used at home, it is recommended to set the channel to 1 or 11 to avoid signal overlap with other routers to the greatest extent. This is because most people don't change this setting and keep the default 6 channels.

3.Of course, there are only three non-overlapping channels provided in the network standard, and the number of non-overlapping channels that can be used is a bit small, but it is enough for the average home or SOHO wireless network. If more than three wireless networks are required in the office area, it is recommended to use a wireless device that supports standards, which provides more non-overlapping channels.

First of all, make sure that your BAI interface is not connected by mistake, the network cable out of the dialer is connected to the daowan port of the zhi router, and the network cable of the computer is connected to the lan port, and then you set up the login account and password in the right router and click to connect, and then you can see whether it is connected, or the router has a status page, you can go to it to check whether it is connected, if it shows that it is connected but still cannot open the web page and surf the Internet, it may be caused by DNS addressing errors, Please use a stand-alone connection to surf the Internet and check the support in the network connection properties to record the DNS address, then connect to the route, and modify the DNS address in the properties of the local connection, which should be on the line.

If you can't connect after setting up the login account and password, the route is basically broken.

When using a wireless router to surf the Internet in daily life, there will be a problem of network disconnection, which may be caused by the instability of the wireless router.

Specific steps: 1.Test the router with the ping command: first in the case of daily use, open the start menu, all programs, accessories, command prompt, and then enter the ping, after which do not close the window and let the computer ping the router all the time.

After a while, press Ctrl+C on your keyboard and you'll see the stats. If the ping does not respond, check whether the IP address of the router is or whether the firewall is blocking the sending of ICMP packets.

5.Improve the heat dissipation of the router: Wireless routers also need to improve the heat dissipation of the router, update the firmware of the router, etc.

Some people like to put the wireless router and the ADSL cat together, or plug the wireless router into the corner, so that the router is easy to overheat and crash, and the natural stability is very poor. Therefore, you must pay attention to the position of the router.

Hello, I took a look at the other copies.

How to test the performance of the router at home after the du. I'm not sure exactly what stage you're testing your router? If you are a router manufacturer, you should conduct network testing during your R&D and production phases to ensure a fast time to market.

If this is the case, I suggest you try Xinertai bigtao220 here, this equipment is a domestic equipment, which is used in electric power, scientific research institutes, communication manufacturing, military industry, coal and other industries.

The wan port is set to bai fixed, and the PC is set to direct pingI can ping through. Description zhiwankou dao

It's good specialty. As for the lan mouth. Generally yes or something. Set the address of the PC in the same network segment. The same general means that the LAN port is good.

Such. Both ports are good. Basically, it can be regarded as a router is good. Use it.

If it's a household bai

wireless routers. In ensure.

In the case that your home network is fine, connect to the inside of the router's DAO management page, try to see if you can connect and log in, and then try to see if you can connect to the Internet, if you can, then it's generally no problem.

If it's a data router, this is... It's complicated to say it's complicated, it's simple to say it's simple. Look at whether the configuration is effective, look at the running status of the router, the CPU, memory, and port traffic are abnormal, and this is about the same.