Is it possible that the computer just bought the same?

The computer from the system is just from the C disk, the other disks have to be deleted by themselves, some temporary files can occupy a lot of space, it may be uncomfortable to look at, windows comes with a disk cleanup and disk defragmentation that can sort out your disk, start - program - accessories - system tools inside, if you can't find it, the next optimization master or super rabbit and the like have to sort it out, but windows comes with that is not recommended to use often, That will break your plate if you use it often, just tidy it up for a month. But if you don't organize it all the time, it will take up a lot of space and affect the network speed and so on.

Got all the grids 、、、

Reinstall the system.

The upstairs method can be used, and the disk is formatted directly. It is also very clean after there is a partition on the system disk!!

One-click restore to install a pull; If you are in a bad mood, restore it. Otherwise, install a software called the shadow system; Very easy to use! It's all about charging.

Buy a restore card and put it on. Anything you put on your computer after it is turned on is gone after it is turned off.

Optimize it with Super Bunny, it's so powerful!

However, you'll have to read the manual carefully, and it's best not to use its default settings.

I've suffered this loss and redone the system.

Find a good system disk and reinstall it.,C drive is left with system files.,Isn't it okay to format other disks?,Or try to clean up system junk software with one click.。

Problem analysis: The computer automatically enters the CMOS interface of the motherboard when it is turned on, if you rule out human error to enter (you can press the ESC key to exit), it means that the computer fails to pass the self-test when it is powered on, which is generally a CMOS parameter error or hardware failure. Common phenomena include battery failure, misconfiguration, poor memory or hard disk contact, etc., which need to be investigated one by one.

Solution: 1. Battery failure: cause the computer to call the default parameters of CMOS, if it is inconsistent with the local hardware environment, the computer cannot be started normally. You can purchase a motherboard battery to replace it, then turn on the computer and press the DEL button (F2 or other designated hotkeys for notebooks) to enter the CMOS interface, and reset the correct parameters, and finally press F10 to save and exit the reboot.

2. Configuration error: This situation will also occur due to the manual configuration of CMOS parameters that do not match the local hardware environment. In general, you can press the F1 key to skip the non-fatal error and start the computer directly according to the prompt message on the black background and white text on the screen, or press the del key to enter the CMOS, then press F9 to load the predefined parameters or select Load optimized defaults or load fail-safe defaults, and then press F10 to save and exit the restart.

3. Hardware failure: If the above operations are invalid, it means that there is a problem with the hardware, generally because the memory and the hard disk may be in poor contact or the main boot record of the hard disk is damaged, and it is necessary to reinsert or repair the boot sector or reinstall the system or replace the hard disk.

Caused by hardware failure, of course, this failure is not necessarily caused by poor hardware quality, this problem is more common. It is recommended to reinstall the computer, and the general problem will be solved. The English above, I'll translate it for you.

Windows boots fail and may have been caused by recent hardware or software changes. Resolve this issue with the following steps.

1. Insert the Windows installation disk and restart the computer.

2. Select the language setting and click "Next".

3. Click "Repair Your Computer".

If you don't have an installed disk, contact your computer system administrator or computer seller to find a solution.

System pre-installation failed! Generally made due to corrupted system installation files!

The system is broken......You **bought, the store in the computer city is still **ah.

If the system fails to boot, it is best to repair it with a system file, but if it doesn't work, you can only redo the system.

An error occurred in the system, and the configuration information was faulty.

1. Restart the computer: In the current state, press and hold the power button to force the shutdown and then restart the computer, if the error prompt no longer appears and can enter the system operation normally, it means that the last abnormal is only an occasional program or system running error, it does not matter.

2. Repair the system: If you frequently can't enter the system normally, press F8 immediately after booting to see if you can enter the safe mode or configure the correct mode for the last time, if so, the system will automatically repair the registry after entering, and recall what operations were done when the first few abnormal phenomena occurred, and according to the suspicion that a certain application software (or driver) caused the problem, uninstall it, and then exit normally, and then restart it should be able to enter the normal mode. If you have security software installed, you can use 360 Security Guard plus 360 Antivirus or Kingsoft Antivirus and other similar security software in safe mode to clean up your computer, optimize and accelerate (remove redundant boot auto-start programs, defragment hard disks, etc.) and check and kill Trojans and viruses.

3. Reinstall the system: If the above operations are invalid, you need to reinstall the system (Note: If the C drive has important data, it needs to be backed up in advance).

There are many ways to install the computer system, in addition to the time-consuming and troublesome complete installation method that is rarely applied now, the commonly used is clone installation, and the method is divided into: hard disk installation, U disk installation and optical disc installation, etc.

The system is pirated and not activated can be tried with pony activation.

Go to the BIOS and select the first boot as the hard disk boot.

Are you an all-in-one machine or an assembly machine?