If the rubber strip of the refrigerator is moldy and wants to be cleaned, how should it be cleaned?

The rubber strip inside the refrigerator is very easy to mold, if the rubber strip in the refrigerator is moldy, it will breed a lot of bacteria in the refrigerator, and it will also make the cooling effect of the refrigerator worse. Not only that, but it will also greatly increase the power consumption of the refrigerator, and it will also reduce the service life of the refrigerator. Therefore, you must always clean the rubber strips in the refrigerator.

But many people think that the rubber strip in the refrigerator is very difficult to clean, and it is not easy to clean, no matter how you wash it, you can't wash it, but in fact, everyone has not mastered the correct cleaning method, as long as you master the correct method, it is very easy to clean the rubber strip. <>

Start by preparing a bowl and pour some white vinegar into it, then put some dish soap and stir them well. Then prepare a piece of gauze, if you don't have gauze, you can also use a face towel to soak it with the liquid you just mixed, and then prepare a discarded card, wrap the card with gauze. Then you can stuff the gauze-wrapped card into the gap between the adhesive strips of the refrigerator and clean it.

This kind of cleaning can not only take care of the edges and corners, but also clean very clean. <>

Finally, use a clean rag to wipe out all the dirty things on it, so that the refrigerator on the point and some bacteria can be cleaned very clean, this method is not only very simple, but also the effect is also very good, after the treatment of the refrigerator, not only the refrigeration effect can be restored to the normal level, but also power-saving and clean, the service life will be relatively long. This cleaning method is not only used in refrigerators, but also for some other household appliances. <>

However, we should pay attention to the fact that the refrigerator should be cleaned frequently, otherwise the bacteria will breed for too long, which is also very difficult to clean, so it is best to clean it every once in a while, and it is best to cut off the power supply when cleaning. After all, the refrigerator is where food is stored, so it is very important to keep it clean.

At this time, you can remove and wash the adhesive strip of the refrigerator, then clean it with dish soap, then rinse it with running water, put it in the sun to dry, and then install it back.

Generally speaking, if the adhesive strip of the refrigerator is moldy and wants to be cleaned, you should use baking soda. Because baking soda has a strong decontamination effect.

You can find a professional person, so that you can clean it very cleanly, and there will be no impurities.

Clean the refrigerator first, then use toothpaste or white vinegar, choose a small toothbrush to clean, this will be cleaner and can also remove odors.

Here's how:

1. Clean with toothpaste. Start by squeezing the toothpaste, apply it to the moldy area of the strip, wait a few minutes, and wipe it with a damp towel or paper. Rinse with tap water.

2. Clean with alkaline-containing substances. We can clean it with alkaline substances, similar to alkaline noodles. Pour a spoonful of alkaline noodles on top of the moldy strips, and after a while, pour some tap water and wipe it.

3. Wash with alcohol. Use chopsticks dipped in alcohol to wipe back and forth on the moldy part of the rubber strip of the refrigerator, and then wipe it evenly with a paper towel, we can see that it is stained with stains. Then wash with clean water and you're done.

4. Wash with vinegar. We all know that vinegar is an acidic substance, and it can be reacted with moldy substances, rubbed back and forth on the moldy area with a cloth dipped in vinegar, and finally washed with water.

5. Laundry detergent cleaning. We know that household laundry detergent can remove stains, so after washing the clothes, we can use laundry detergent to wipe the mold.

6. Detergent. Detergent is generally used to wash dishes, of course, it can play a role in sterilization and cleaning, which is also a quick way.

1. You can use toothpaste to apply the moldy place in the refrigerator strip, find a toothbrush, gently brush off the mold after the toothbrush is dipped in water, and finally wipe it clean with a rag.

2. You can also mix vinegar and water and add dish soap to gently wipe the mildew of the rubber strip.

3. You can also put alcohol in a bowl, wrap a paper towel with a fork and cover it with alcohol, and press and wipe it repeatedly along the gap of the sealing strip.

If you find that the refrigerator strip is moldy, you can add an appropriate amount of white vinegar and dish soap to the bowl with water and mix it thoroughly. Then soak the rag in water, take a card and wrap it in a damp rag, peel off the seal, and wipe the moldy place directly with the rag wrapped with the card, and you can clean it.

You can also prepare an ointment, apply the ointment to the moldy place of the refrigerator adhesive strip, wait for about three minutes, continue to gently scrub it with a toothbrush, and then use a dry rag to clean the mold, the ingredients in the ointment can effectively remove the mold, and it can also have a good disinfection effect.

If there is alcohol at home, you can also use alcohol to wipe the moldy refrigerator strips, if there is no alcohol, you can also replace alcohol with liquor, but the effect is not particularly obvious, if it is mold in the gaps, you can use paper towels dipped in some alcohol, and then press and wipe repeatedly, you can also remove the mold in the cracks.

Causes of moldy fridge strips

One is that the food in the refrigerator smells of each other, and the other is that bacteria will accumulate and cause mold after a long time in the refrigerator.

Although the refrigerator temperature is low, the spores do not multiply at sub-zero low temperatures, but their vitality is very tenacious, they can survive at minus 50 degrees, and if the temperature rises, the spores will return to activity.

If the mold in the refrigerator strip is not treated for a long time, even if we can't see it with the naked eye, it will affect the hygiene of the food, and we will have a negative impact on our health when we eat it. Therefore, if the refrigerator adhesive strip is moldy, don't pay attention to it, and deal with it in time for your health.

How do you clean a moldy refrigerator strip? After the refrigerator strip is moldy, it should be cleaned in time to ensure the cleanliness of the refrigerator. Next, I will introduce it to you.

Toothpaste

Apply the toothpaste to the moldy place in the refrigerator strip, wait for 2-3 minutes, find a toothbrush without it, dip it in water and gently brush off the mold with toothpaste, at this time the mold is very easy to brush off. Finally, wash it with water and wipe it with a dry rag.

Vinegar

Vinegar can be a good way to eliminate mildew, vinegar and water are diluted in a ratio of 1:5, then add dish soap, and then take a dry rag or an old toothbrush dipped in vinegar water to gently wipe the mildew of the rubber strip, and the mildew will be easily wiped off by us, which is very simple and practical.

Alcohol

Pour alcohol into an open bottle or bowl and wrap a paper towel around a fork, taking care to keep it firm. Then, a paper towel from a fork is placed into the container bridge to fill the mouth with alcohol, and the gap between the sealing strips is pressed and wiped repeatedly.

Tips:If you can't handle it yourself, get a professional to have it inspected and repaired to avoid more damage.

The method of cleaning the moldy strip of the refrigerator is as follows:

1. Vinegar, we can use daily vinegar to clean the moldy sealing strip of the refrigerator, and also clean the inside of the refrigerator, which can not only remove stains and mildew, but also disinfect, sterilize and remove odor. It is also safe and effective than placing a refrigerator deodorant. 2. Toothpaste, when the sealing strip on the refrigerator door is moldy, we can use toothpaste to help clean it.

First apply the toothpaste to the moldy area of the sealing strip, wait for a while, gently wipe it with a towel or soft cloth (be careful not to pull the sealing strip too hard to prevent deformation and loose sealing), and then wash it with water. Third, the hair dryer, after wiping the sealing strip, there will be the problem of the sealing strip deformation and loose sealing, at this time we can use the hair dryer to help it recover. The operation is very simple, directly blow with a hair dryer, and the sealing strip will soften and return to its original shape in a few minutes, then it can be fixed on the refrigerator.

The rubber strip of the refrigerator is moldy and difficult to clean, so it is recommended to clean the refrigerator door seal with 84 disinfectant, which has a good effect.

There is a lot of mold in the refrigerator tape, and you can get it with one trick.