Who understands the installation steps of the wardrobe sliding door slide

The installation steps of the sliding door wardrobe include the security bottom plate, the fixed frame, the installation of the top plate, the installation of the partition plate, and the fixed door rail.

Six steps to install the clothes pole.

1. Place the bottom plate.

The floor where the bottom panel of the wardrobe is placed should be cleaned beforehand, because it will be very troublesome to clean it after installation.

2. Fix the frame.

Install the side and back panels of the wardrobe according to the grooves on the panels, and adjust the position between the panels.

3. Install the top plate.

It is best to prepare a stool for climbing on the spot, and the top board should be raised and placed on it, and then fixed.

4. Install shelves.

Place the shelf where the screws have been screwed in advance and secure. Pay attention to adjusting the fixed position of the shelf, back and side panels.

5. Fix the door rail.

Door rails are installed on the top and bottom edges of the wardrobe, and the alloy material for the door rail is better, light and firm.

6. Install the clothes rail.

Fix the rivets in the reserved position and install the clothes rail. Pay attention to the balance between the two sides, and you're done.

1. The size of the track box on the upper part of the sliding door should be guaranteed to be 12 cm high and 9 cm wide. Like the curtain box, the track box is installed inside the track, and the sliding door can be hung on the track. When the height of the door is less than a meter, it feels oppressive.

Therefore, when making a sliding door, the height should be at least 195 + 12 = 207 cm or more.

Second, the size of the normal door is about 80 cm 200 cm, under this structure, the door is relatively stable, and at the same time very beautiful. Therefore, the ratio of width and height of the sliding door should be similar to the size of the sliding door.

3. Be cautious of using the sliding door (open hanging track box) from the ground to the top. Due to the excessive swing amplitude when pushing and pulling, the sliding door is easy to deform after a long time, and the door cannot be opened after deformation, which means that it cannot be repaired and cannot be used.

Fourth, when installing the sliding door track, fix the upper track, use the gravity cone (hanging wire hammer) at both ends of the upper track and the midpoint to hang 3 points on the ground with a grease pen to draw the point to set the surface, install the upper track, and then put a hammer to the ground at the center point of the upper track, put the vertical line at both ends of the track, and fix the lower track on these 3 points so that the upper and lower tracks are completely parallel, and the push and pull of the sliding door is in the best state.

Drawer slide rail installation method.

Drawer slide rail installation first determine what kind of drawer slide rail to use, generally using three hidden slide rails, please follow a certain data, determine the length of your drawer, and the depth of the counter, in order to choose the corresponding size to install on the drawer.

Secondly, assemble the five plates of the drawer, screw on the drawer panel, the drawer panel with a card slot, after processing, put the drawer on the already installed drawer, let the adjustment nail hole position match, and then push the locking nail into the locking drawer and slide rail.

Finally, to install the cabinet, you need to screw the plastic holes on the side panel of the cabinet first, and then install the track removed from above. Both sides of the cabinet should be installed and secured. (Content excerpted from: Master Wan).

When installing a wardrobe in the bedroom, you need to pay attention to the installation track. What are the steps for the installation of sliding wardrobe door slides? PChouse will take you to find out.

1. The size of the track box on the sliding door should be 12 cm high and 9 cm wide. Just like a curtain box, by installing the track inside the track box, you can hang the sliding door on the track. If the height of the door is less than a meter, it can feel oppressive.

Therefore, when making a sliding door, you must ensure that the height is at least 207 cm.

2. Generally speaking, the size of the normal door is about 80 cm to 200 cm, because under this structure, the door will be relatively stable and look more beautiful visually. Therefore, the ratio of width and height of the sliding door should be similar to the ** size.

3. It is best not to use a sliding door (open hanging track box) from the ground to the top. Because the swing amplitude is too large when pushing and pulling, the sliding door is easy to deform after a long time, and the door cannot be opened after deformation, which means that it cannot be repaired and cannot be used.

4. Finally, the track for installing the sliding door. Fix the upper track, then use the gravity cone (hanging line hammer) to hang 3 points at both ends and the midpoint of the upper track, draw the 3-point fixed surface with a grease pen on the ground, and then install the upper track, and then put a hammer to the ground at the center point of the upper track, put the vertical line at both ends of the track, and fix the lower track on these 3 points, so as to ensure that the upper and lower tracks are completely parallel, and the push and pull of the sliding door is in the best state.

Summary. Dear, I am glad to answer for you: how to install the sliding door pulley**What is the reason for the return of the wardrobe sliding door after installation?

1. Take a frame and lower seal, and fix it with fixing screws; 2. Place the fixed frame on the ground, and then arrange the sliding door panel on the frame; 3. Take another frame and snap it into the arranged sliding door panel, and fix the lower seal and frame with screws; 4. Snap into the upper seal, fix it with screws, and fix the upper pulley at the same time; 5. After the upper and lower screws are fixed, fix the slide wheel in the lower seal with traction screws to complete the installation; 6. Note: When installing the sliding wheel, the pulley shrapnel is inward. Wardrobe Pulley Track Door Installation Details Wardrobe Pulley Track Mounting Accessories:

upper pulley, slide wheel, fixing screw, slide wheel traction screw, etc.; Upper and lower pulley installation position and fixing method. Basically, the installation method of the wardrobe sliding door is the same, but there are also some installation methods that are slightly different because of different designs, it is recommended to install the wardrobe when the wardrobe is installed, and the installation fee can be uniformly given. Thank you for your patience <>

I hope you are satisfied with my service and I wish you all the best again! Peace and joy!

How to install the sliding door pulley**What is the reason for the return of the wardrobe sliding door after installation.

Dear, I'm glad to answer for you: How to install the sliding door pulley**What is the reason for the return of the wardrobe sliding door after installation? 2. Place the fixed frame on the ground, and then arrange the sliding door panel on the frame; 3. Take another frame and snap it into the arranged sliding door panel, and fix the lower seal and frame with screws; 4. Snap into the upper seal, fix it with screws, and fix the upper pulley at the same time; 5. After the upper and lower screws are fixed, fix the slide wheel in the lower seal with traction screws to complete the installation; 6. Note:

When installing the slide wheel, the pulley shrapnel is pointed inward. Wardrobe pulley track door installation details Wardrobe pulley track installation accessories: upper pulley, slide wheel, fixing screw, slide wheel traction screw, etc.; Up and down the installation position and fixing method of the slower shroud cover wheel.

Basically, the installation method of the wardrobe sliding door is the same, but there are also some because of the different design of the installation method will be slightly different in the pin cover, it is recommended to install the wardrobe when the wardrobe is installed, and the installation fee can be uniformly paid. Thank you for your patience <>

I hope you are satisfied with my service and I wish you all the best again! Peace and joy!

It is recommended to contact the after-sales party of the wardrobe and ask a professional installer to install it.

2. Drill holes after positioning. 3. The two sides are fixed and the hole in the middle is drilled. 4. Install the lower rail, wipe it clean first5, and then fix the position of the lower rail, and clean the inner layer of the track with a brush.

6. Sliding door installation. First of all, the door is gently lifted to let the upper pulley of the door enter the upper track, and then one hand cracks and rolls to lift the sliding door hard, and the other hand pulls the sliding wheel, so that the lower wheel smoothly enters the lower track. 7. The installation of the sliding door is completed, and the next step is to paste the anti-collision strip to protect the sliding door.

8. Complete the renderings. Extended information: the importance of pulleys in the wardrobe 1, pulleys are a very small hardware in the wardrobe, but they play a very important role, there are many kinds of pulley materials on the market, there are plastic pulleys, metal pulleys and glass fiber pulleys 3 kinds.

Among them, the plastic pulley is hard, but easy to break, and will be astringent and hard after a long period of use, and the feeling of pushing and pulling will become very poor, while the metal pulley is strong, but it is easy to produce noise when it comes into contact with the track. 2. The pulley is the key factor that directly affects the service life of the wardrobe and the sliding door is the pulley. The pulley is designed to last for about 15 years.

The pulley of the wall cabinet door consists of two parts, one is the top wheel and the other is the bottom wheel. There are two ways to install the bottom wheel, one is implicit and the other is external. The implicit bottom wheel means that the bottom wheel is installed under the door, and after putting it into the guide, you can see the orange from the front and back of the door.

3. The pulley made of glass fiber material is the most wear-resistant on the market today. The pulley slide process is miscellaneous, whether the pulley is smooth, pressure-resistant, wear-resistant, safe and reliable is the most important thing that consumers should pay attention to, and the household generally requires more than 60,000 times of push and pull.