How to maintain a fully automatic washing machine without drainage

1. The drain pipe is twisted, and only by keeping the drain pipe unblocked can the washing machine drain normally. The drain can be rearranged or replaced.

2. When the drainage is slow, it may be because the drain port is too high and the tension spring strength of the drain valve is not enough, so that the valve core is opened. The drain can be lowered and the tension spring can be replaced to solve the problem. Open the back cover of the washing machine and check whether the drain valve strap has fallen off and whether the valve strap or drain lever is broken and causing blockage.

3. Check whether the drain filter and drain valve in the barrel are blocked by debris, causing slow drainage or even no drainage.

4. It is possible that the dirty material of the clothes is blocking the drain. At this time, the drain filter should be removed for cleaning, and the drain should be flushed with water and the debris in the drain valve should be removed.

5. If there is a fault in the drainage of the automatic washing machine, select the washing machine program to the single dehydration program and start it, and listen to the drainage electromagnet.

Whether there is a "pop" suctioning sound.

6. If there is a suction sound, it means that the drain solenoid is normally sucked, and the drain valve may be blocked; The drain valve tension spring falls off or is corroded and broken, and the damaged parts need to be cleaned and replaced.

7. If there is no suction sound of the drain solenoid, the back cover should be opened to check whether the plug-in wire of the drain solenoid falls off? If it falls off, it can be used after reinserting. If it does not fall off, a multimeter can be used.

Measure the resistance of the two terminals of the drain solenoid, if the resistance value is infinity or less than 30 ohms, it means that the drain solenoid has been broken or short-circuited, and should be replaced. If it still does not work properly after replacement, it may cause the failure of the program controller due to the burning of the drain solenoid (usually the thyristor that controls the drainage.

damaged), the degree controller needs to be overhauled.

If there is a lot of laundry, it may cause the drum to be unbalanced, and the washing machine will not be dehydrated; When the washing machine is dehydrated, if the lid is opened, the top switch will be damaged; If you choose to dehydrate at a low speed in absorbent clothes, you may have the illusion that you cannot be dehydrated; When there is too much foam in the barrel, the water level switch cannot be reset, and it will also cause dehydration. Here's why:

1. The washing is in an unbalanced state.

If there is a lot of laundry, when the washing machine is rinsed, the laundry will be grouped together due to knots and entanglement, causing the washing machine drum to be unbalanced. At this time, the washing machine will adjust to a low speed, resulting in no dehydration. If this is the case, as long as you put less clothes in it, it will not affect the dehydration.

2. The safety switch on the top cover of the washing machine is damaged.

The washing machine is running at high speed when it is spinning, try not to open the lid at this time, otherwise the top switch will be damaged. If the switch is damaged, it will not be able to dehydrate.

3. Caused by the texture of clothing.

There are many types of clothing in winter, such as some tweed types of clothes, which are more absorbent. If you choose to dehydrate at a low speed, you may appear to be unable to dehydrate. For this kind of highly absorbent clothing, high-speed dehydration should be chosen.

4. The drainage system of the washing machine is blocked.

When the drainage system is blocked, it will also cause the water in the barrel to not be discharged, and when there is too much foam in the barrel, the water level switch cannot be reset, and then there is no way to enter the dewatering procedure. If this is the reason why you can't dehydrate, you can remove the drain filter for cleaning to remove some of the debris inside.

Reason 1: The function of the washing machine program is abnormal Maintenance method: The washing machine does not drain due to this reason is the easiest problem to solve. When encountering such a problem, just put the laundry.

After the power is off, rebooting is OK.

Reason 2: The drain valve is blocked or the water pipe is bent and deformed, resulting in the washing machine being unable to drain water. Maintenance method: When carrying out maintenance, you only need to open the valve cover of the drain valve and take out the debris in it.

Clean the washing machine regularly and regularly:

There are also many options for cleaning methods, you can ask professional staff to clean, which is the easiest for yourself, but the cost is relatively high;

In addition, it is also a good choice to use a professional detergent for cleaning the washing machine, the effect of decontamination and sterilization is very good, and the cost is appropriate, and the operation is relatively simple.

In addition to these, in fact, when buying a washing machine, you can also consider a no-clean washing machine, which has a great advantage that it can keep itself clean for a long time, so you don't need to think too much about and pay attention to the cleaning problem of the inside and outside of the washing machine.

1. The function of the washing machine program is abnormal.

Solution: The washing machine does not drain due to this reason is one of the easiest problems to solve. When you encounter such a problem, you can simply turn off the power of the washing machine and restart it.

2. Power failure causes the washing machine to fail to drain water.

Usually, the failure can be divided into two situations, which are the loosening of the parts of the drain valve and the drain solenoid, or the breakage of the tension spring of the drain valve.

Solution: During the inspection, if it is found that the drain valve core tension spring of the washing machine has been broken, then although its solenoid valve can absorb air when draining, the drain valve valve cannot be drained if it is not opened. At this point, it is only necessary to replace the tension spring again.

3. The drain valve is blocked.

The drain valve is blocked or bent and deformed, causing the washing machine to fail to drain water.

Solution: When making repairs, you only need to open the drain valve cover and remove the debris inside.

Daily inspection of washing machine drainage:

1. When the washing machine cannot drain water, check whether the adjusting rod nut on the drain valve is loose, or whether the cable of the tractor cannot open the valve core and cannot drain the water.

During the inspection, if it is found that the fixing nut of the washing machine is not loosened and its cable is not loose, then it means that the water retractor has been damaged and its drain valve core cannot be opened, and the retractor of the washing machine needs to be replaced.

2. The gap between the drainage rod and the rubber valve of the washing machine becomes larger, which will also lead to the inability to drain, and the gap between the drainage rod and the rubber valve needs to be properly adjusted.

3. When the core damping in the drain solenoid valve in the washing machine is too large, or the suction power becomes smaller, it will also cause the washing machine to fail to drain, at this time, the rust in the solenoid in the washing machine can be removed, and its drain solenoid valve can be replaced at the same time.

Answer dear, there are the following possibilities: 1. The drain pipe in the washing machine may be damaged or blocked, as long as there is a problem in the body, it is easy to cause the washing machine not to drain. At this time, we need to carefully check whether the drain pipe of the washing machine is blocked or damaged, dredge the drain pipe in time, and replace the drain pipe with a new one in time if it is damaged. 2. The operation of the washing program of the washing machine may not be standardized, as long as the washing machine is not standardized, it is easy to cause the washing machine not to drain.

We just need to follow the correct procedures. 3. The water level in the washing machine may be too high and may not be able to drain the water. If the water level is too high, the washing machine will be overloaded during the washing process, which will also cause the water to be unable to drain in the short term.

Wait a little longer for the water to drain out properly, and don't put too much clothing in the process. 4. It is also possible that the drain parts of the washing machine are loose or broken, resulting in the washing machine not being able to drain properly, as long as it is tightened or replaced with new components. I hope my answer will be helpful to you, and I wish you all the best, thank you for giving me a thumbs up.

1. The drain pipe in the washing machine is damaged or blocked. A washing machine is made up of many parts. Once there is a problem inside the body, it is easy to cause the washing machine to not drain water.

You can check that the drain pipe of the washing machine is blocked or damaged, and dredge the drain pipe in time, if it is damaged, you need to replace the drain pipe with a new one.

2. The washing program of the washing machine is not operated correctly. Once the washing machine is used improperly, it is easy to cause the washing machine to not drain. Just follow the right procedure.

3. The water level in the washing machine may also be too high, and it may not be able to drain the water within the specified time. If the water level is too high, the washing machine will be overloaded while washing clothes, which will also cause the water to be unable to drain in the short term. You can wait a little longer, the water in the washing machine can be discharged normally, and don't put too much laundry when washing clothes.

4. If the drain of the washing machine is installed too high, the water in the washing machine cannot be discharged, and the position of the drain pipe needs to be lowered.

5. If the washing machine drain gate assembly is loose or damaged, the washing machine cannot drain normally. Just tighten it or replace it with a new component.

6. If the fixing nut is not loosened or the cable is not loosened, the retractor may be damaged and the drain valve core cannot be opened, and the retractor should be replaced at this time.

Hello dear, is answering this question for you, you need to wait patiently for about three minutes, the answer will be revealed for you immediately, please don't worry!

The washing machine does not drain with just these few steps, which can be easily solved.

The possible reasons why a fully automatic washing machine does not drain are as follows:

a. First of all, check whether the adjusting rod nut on the drain valve is loose, and whether the tractor cable is loose from the drain valve, resulting in the retractor being unable to pull the drain valve core apart and causing non-drainage;

b. If the fixing nut is not loosened or the cable is not loosened, the retractor may be damaged and the drain valve core cannot be opened, and the retractor should be replaced at this time;

c. There may be debris blockage in the drain valve or bending and deformation of the drain hose, at this time, unscrew the drain valve cover first and take out the debris;

d. The gap between the drainage rod and the rubber valve becomes larger, as long as the gap between the drainage rod and the rubber valve is appropriately adjusted.

e. The spring in the drain valve is too long or loses its elasticity. Just replace the inner spring.

f. The damping of the moving core of the drainage solenoid valve is too large or the suction force becomes smaller. Remove rust and dirt from the solenoid or replace the drain solenoid valve.

g. If it has not been solved, the computer board may be damaged, and the computer board should be replaced.

For the above reasons, according to your description, I judged that it may be that your computer board on the control of drainage of the thyristor breakdown, if you understand, check this problem carefully, try not to replace the whole board (computer board 120 yuan). If there's anything you don't know, can you tell me? I'll be sure to help you.