Where is the drain valve of Konka automatic washing machine?

The automatic washing machine drains water while entering the water, which should be a problem with the drain valve of the washing machine.

If the drain valve of the washing machine is not completely closed or closed loosely, water will flow out after filling and during normal use. It is necessary to check whether the drain spool is reset.

It is possible that the washing residue in the drain valve body is blocked, the drain valve core is not closed tightly, and there will also be leakage after water injection.

Konka automatic washing machine drains water while entering the water, and the washing machine cannot be used normally.

It is recommended to contact the after-sales service department of Konka washing machine for repair or clean the drain valve.

Enroll. Consultation.

Information home page installation knowledge home appliance installation text.

Home furnishing enterprises after-sales service, distribution, installation, maintenance, and return to find a master to find a master to place an order with one click.

How do you open the drain valve of a washing machine? Steps to remove the drain valve of the home washing machine by yourself**.

The drain valve of the household washing machine is installed on the chassis of the washing machine, and it is connected with the drain port of the bucket with a rubber sleeve and sealed with glue. The drain valve is connected to the lower mouth of the bucket through the overflow pipe. The drain port of the drain valve and the drain spool pipe (glued to the joint on the box) are fixed with spring clips, and the spool tension spring hook protruding from the middle hole of the bonnet is in the hole of the adjustment frame.

How to open the drain valve of a household washing machine:

Fully automatic washing machines do not have an automatic drain function, and the drainage function can only be achieved by using other programs.

Select the Single Drift program. In the general single rinse, the first thing to perform is to drain the dewater, and there is a certain time interval between the emptying of the water and the start of the dehydration procedure, as long as the time is grasped to stop the machine operation.

Washing machine drain valve self-disassembly steps:

1) Use pliers to remove the cotter pin where the solenoid valve armature is connected to the adjustment frame.

2) Loosen the chassis connecting screws and remove the overflow pipe and drain spool.

3) Hold the valve body and rotate it left and right several times to separate the valve body from the drain port of the bucket, and then the drain valve can be removed.

When the drain valve is installed back on the machine, the rubber sleeve should be glued with the drain port of the bucket with adhesive first, and then the drain valve should be connected to it, and the stroke of the electromagnet should be adjusted at the same time. Adjust the correct position of the fork when the electromagnet armature is separated and suctioned, that is, when the electromagnet is energized, the armature is engaged, and the fork is opened, so that the distance between the fork head and the ratchet is greater than 1.5 mm; When the DC electromagnet is powered off, the armature is pulled out, and the head of the pawl of the fork should be aligned with the ratchet axis, and the pawl should extend into about two-thirds of the height of the ratchet teeth, so as to ensure the normal operation of the relevant components.

If you want to replace the drain valve cover or remove the drain valve inner skin tiger (or spring), use a screwdriver to clamp on the two convex heads of the valve cover, and turn the screwdriver in the direction pointed by the arrow to loosen the valve cover (some washing machine drain valve covers do not have a convex head, you can unscrew it by hand).

Although the washing machine drain valve sounds like it is very troublesome and professional, for people who don't understand, if it fails, they will definitely find a master to check and repair it, of course, you can't say no, but it takes more time and energy. And what I said above is for those families who don't understand anything at all, and if the drain valve is broken, at least we will check it, and the simple fault will be repaired by ourselves, and it is not too late to ask the master for a little trouble. I hope what I'm saying can help you.

Master Wan)

The possible causes and solutions of a fully automatic washing machine are as follows:

1. Check whether the valve core of the drain valve is stuck in the power-off state. It is possible to see if the spool rod is in place, otherwise the internal spring may be stuck. At this time, the valve cover should be unscrewed and checked for foreign objects stuck or damaged, which should be replaced if damaged.

2. If the drain valve is normal, check whether the drawbar of the tractor (12 13ko) is in place, and whether the drawbar is flexible when pulled and retracted by hand. If it gets stuck, it means that the inside of the tractor is damaged and should be replaced.

3. If the forward traction device is normal, whether the traction device has also been started in the state of water supply, and the drain valve core has been shaken to discharge the water. If yes, it indicates that the computer board program has been disrupted and the computer board should be replaced. However, it is usually a foreign object (coin or button) stuck in the spool of the drain valve, which causes the valve to not die.

Drain valve foreign matter treatment method (take Haier washing machine as an example):

Unscrew and remove the back cover with a Phillips screwdriver to see the inside of the washing machine.

When you see the bottom, you can easily find the valve connection of the outlet pipe along the outlet pipe and turn on the wire.

There is a layer of yellow glue on top. It can be scooped out with a flathead screwdriver. There is an iron clamp on the tube head that can be pressed down by hand. You can easily pull out the water pipe with a screwdriver. It is important to note here that brute force cannot be used to extubate.

Then clean up the stuck stuff. Any small object such as hairpins, coins, buttons, etc., will block the outlet valve, making it impossible to close and leaking. These small items tend to fall into the washing machine, so it's best to check them before washing.

If there are no small objects on the outlet pipe head, the outlet valve can be touched upwards for a thorough inspection.

The working principle of the water inlet solenoid valve:

The function of the water inlet solenoid valve is mainly to control the inlet of tap water and provide the right amount of washing water and rinse water for the washing machine. The switching of the water inlet solenoid valve is mainly completed by the coil control moving core in the valve. If the coil is not energized, the faucet will be turned on at this point and the water will not flow into the washing machine.

When the coil is energized, the valve opens and the tap water flows smoothly into the washing machine.

The basic structure of the water inlet solenoid valve is mainly composed of a solenoid valve and a rubber valve. The working principle is that when the solenoid coil is energized, a magnetic field is formed, which attracts the iron spool to move upward, away from the diaphragm, and conducts the flow of water.

After the solenoid coil is de-energized, under the action of the return spring and gravity, the valve core sinks and compresses the diaphragm to block the waterway and stop pouring water into the washing machine. The inlet of the water inlet solenoid usually has a filter to prevent dust from blocking the rubber valve of the water inlet solenoid valve.

Hello, Konka automatic washing machine washes water while washing, and it is normal that the water inlet valve is still in working condition, which will make the clothes cleaner!

If the Konka washing machine always drains, it could be a few problems:

1.Valve family door problem: check whether the water valve is opened, and make sure that the drainage pipe is unobstructed when discharging sewage.

2.Water level controller failure: Check whether the water level controller in the washing machine is damaged, and replace it with a new water level controller.

3.Leak detector failure: The water leak detector inside the washing machine may cause drainage failure, check and replace the corresponding parts.

4.Drain pump failure: If the drain pump of the washing machine has a problem with the world, it may cause poor drainage or no drainage, and the drain pump needs to be reinstalled or replaced.

In short, Konka washing machine always draining may be caused by multiple reasons, which needs to be comprehensively judged according to the specific situation, if the above methods cannot solve the problem, it is recommended to contact professional maintenance personnel immediately for repair.