What s the matter with the sudden empty opening tripping of the bathroom socket?

The reason for the tripping is that the socket may be short-circuited due to water, the second is that the electrical appliance is short-circuited due to moisture, and the third is that the live wire of the electrical appliance is short-circuited with the ground wire. Judging the method, unplug all electrical appliances in the bathroom, make sure that there is no water entering the socket, and then close the air and try to open it.

Leakage is possible. The humidity in the bathroom is high, and even the water enters due to shower water or condensation of water vapor. This is handled by a professional electrician.

It means that there is a short circuit, due to the large water vapor in the bathroom, it may make the socket contact temporarily short circuit, resulting in empty tripping. It should be checked and measures taken to keep the inside of the socket dry.

Because the environment in the bathroom is often in the case of high humidity, the socket installed in the bathroom will cause leakage between the poles due to moisture, and the leakage will trip due to leakage.

It is recommended not to install any socket in the bathroom to avoid electricity leakage causing trouble, and even when using the socket, it can lead to the occurrence of electric shock.

There may be leakage! Unplug the electrical appliances on the socket, close to see if it still jumps, jump means that the line is damp and leakage, and if you don't jump, it is a leakage of electrical appliances.

The corresponding air switch of the bathroom socket suddenly tripped, it may be that the electrical load of this socket is too large, resulting in the corresponding air switch tripping protection.

In the case of a short circuit, it is best to find a professional master to repair and deal with it in time, so as to avoid serious fire and economic losses. This situation must not be negligent and cause consequences. to protect our homeland.

The corresponding air switch tripping is an overload or short circuit fault in the line.

The circuit switch of the toilet socket trips, and it may be that the socket or its wiring is faulted by moisture leakage.

If there is a short circuit, the water vapor in the bathroom is relatively large, and the water vapor is applied to the socket, which is easy to cause a short circuit.

It is possible that the short circuit is caused by moisture.

It may be a leakage, or a place with UMC.

Explain where there is a short circuit, check it.

The bathroom socket is out of power, but what is the reason that it has not tripped?

Kiss! Hello, happy to answer your <>

The toilet socket is out of power, but what is the matter if it doesn't trip? The first point of the switch, if you find that multiple sockets in your home are powered off at the same time, regardless of whether the switch trips, you need to check the switch first.

If there is a "self-reset overvoltage and undervoltage tripping" on the branch switch of the socket circuit, it may lead to the power failure of the line, but there is no tripping. At this time, it needs to be manually reset and wait for about a minute to restore the power supply. If the power supply is not restored, it is possible that the self-reset function of the self-reset is damaged by the overvoltage and undervoltage tripping, and a new one needs to be replaced.

The second point of the socket needs to be considered by the socket itself. If there is no fault in the distribution box, or if the individual socket is out of power, then it is necessary to focus on checking the socket. Open the socket to check the wiring at the back, and carefully observe whether there is any slippery wire, disconnected wires or not fixed properly.

After confirmation, start testing the wire, and then determine whether it is a problem with the socket or the wiring. The last point of the line is the line problem, at this time you need a multimeter, which is used to test the voltage between the neutral line and the live wire. Data viewing is very simple, if the voltage is 220V, the line is normal, go to the wheel to replace the socket; If the voltage is shown as 0, or only a few tens of volts, it means that there is a problem with the line.

In the absence of a trip, there is a problem with the line, indicating that there is a break point in the line. If the home is a bright line, you need to test the live wire with an electric pen before checking, and if you can light up the electric pen, it means that the zero line is disconnected; If it can't be lit, it's in the line of fire! Then find the connector closest to the dead socket, and use the buzzer of the multimeter to measure the neutral line of the dead socket to the connector.

If there is no beep, then the wiring needs to be replaced; If there is a beep, it means that the line is okay and the connector needs to be reconnected. Hope mine can help you <>

Do you have any other questions?

Dear, we are happy to serve you, the answer is as follows: This kind of fault is a common fault, but it is not a simple fault, Bizhou Tsai must ask a professional electrician to test on site. The analysis is as follows: 1. The method of judging the water heater is correct.

Similarly, if there is a suspicion that there is a fault in other electrical appliances in Zhuhu, you can disconnect this electrical appliance and connect it to another place, and if the fault disappears, you can conclude that the trip is the fault of this electrical appliance. 2. If there is no problem with all the electrical appliances in the bathroom after inspection, it can be determined that the power supply line has been short-circuited. 3. It is necessary to check from the gate box in sections.

But the condition is when the failure occurs. If the fault comes and goes, it is not easy to check. 4. It is recommended that you disconnect the bathroom from the gate box and use the temporary power supply line to supply power.

After using it for a period of time, if the fault disappears, it means that there is a problem with the power supply line of the bathroom. You can ask a professional electrician to replace the dark wires in the bathroom. 5. If the dark wire cannot be replaced, you need to ask a professional electrician to arrange the open wire indoors.

Check whether there is a leakage place, or the current is too large, unplug all the electrical appliances If it still jumps, then remove the 2 lines below the empty opening, if it also jumps, it must be the empty opening is broken.

There are several reasons for this problem, the most likely first cause is a loose neutral wire, and the most likely second cause is an overloaded air switch.

You first see what causes the trip, if it is leakage, the reset button of the leakage protector will pop up, the switch does not heat, if there is a short circuit, the reset button of the leakage protector does not pop up, the switch does not heat up, if it is overloaded, the switch heats up, and the reset button of the leakage protector does not pop up