Tripping when the bathroom lights on? What causes tripping after turning on the light for a few minu

The socket is damp and causes a short circuit to trip.

It is more likely, you can remove the socket after pulling the brake and check and pay attention to tighten the inherently loose connector screws, and pay attention to maintaining the distance between the wires in the box when reinstalling it back.

Analysis of the reasons for the tripping of the toilet switch:

1. If the socket in the bathroom is mainly used to connect the water heater, and now it is found that it often trips from time to time, test whether the water heater itself is faulty, if you suspect that other electrical appliances are faulty, you can disconnect this electrical appliance and connect it to other places, if the fault disappears, you can conclude that the trip is the fault of this electrical appliance.

2. If there is no problem with all the electrical appliances in the bathroom after inspection, it can be determined that the power supply line has been short-circuited.

3. It must be inspected in sections from the gate box. But the condition is when the failure occurs. If the fault comes and goes, it is difficult to check.

4. It is recommended to disconnect the toilet from the gate box and use the temporary power supply line to supply power. After using it for a period of time, if the fault disappears, it means that there is a problem with the power supply line of the bathroom. You can ask a professional electrician to replace the dark wires in the bathroom.

5. If the dark wire cannot be replaced, you need to ask a professional electrician to arrange the open wire indoors.

If the socket in the bathroom is used to connect to the water heater, it is now found that it will trip from time to time.

Looking for a professional electrician, professional things, looking for professional people, your problem is a short circuit in the line, which is quite serious, and my analysis will not be as simple as changing a light bulb.

1.The lamp is short-circuited, and the line is short-circuited after the switch is turned on, causing tripping.

2.The line is mixed, and the general home lighting system and the socket DAO system are separated, and the socket circuit is connected in series with a leakage circuit breaker in the distribution box. If the neutral line of this lamp is connected to the socket circuit, the neutral current flowing through the leakage circuit breaker will be stronger than the live wire current after the light is turned on, which will make the leakage circuit breaker misjudge that leakage has occurred and tripped.

In the same way, if the neutral wire of the lamp is connected to the lighting circuit and the live wire is connected to the socket circuit, it will also cause the leakage circuit breaker to trip.

It may be that the light in the room is short-circuited, don't turn on the room light first, turn on the other if it doesn't jump, and then turn on the room, if it's still like this. Then it proves that this is the problem, then it must be checked clearly and troubleshooting. First remove all the lights in the room, and then install them one by one, and if you jump to that one, it is a problem with the lamp or lamp head.

Summary. Hello I'm glad to answer for you, the bathroom always trips may be a problem with the toilet socket line, three situations, one is not enough load; Second, the zero line of the toilet socket line is shared with the lighting, which will cause current imbalance and trip; The third is that the toilet socket line is used together with other lines. Get a professional electrician to check it out.

What to do if the bathroom keeps tripping.

Hello I'm glad to answer for you, the bathroom always trips may be a problem with the toilet socket line, three situations, one is not enough load; Second, the zero line of the toilet socket line is shared with the lighting, which will cause current imbalance and trip; The third is that the toilet socket line is used together with other lines. Get a professional electrician to check it out.

Hello, the second situation is that the bathroom trips as soon as it takes a bath because a large amount of water vapor on the switch and socket during the bath, forming a conduction, and the insulation value of the cable or switch decreases, and after the air is dry, the brake can be used normally, which indicates that there is a short circuit in the wire, and the wire should be replaced in timeThere are two kinds of tripping, one is the excessive power of the electrical appliance, and the other is the phenomenon of leakage. You see what your situation is.

It is recommended to find a professional electrician who repairs it, and it is not recommended to repair it yourself

Calculate how much it will cost you to renovate your home

Recently, some netizens asked for help, there was a problem with the circuit at home, as long as the light was turned on, it tripped, what is going on? Is there any good way to solve it?

1. What happens when the light is turned on and it trips.

1. As soon as the light is turned on, there is a problem of tripping pin, which is nothing more than two reasons, one is the problem of overload in the circuit, and the other is the fault problem of wiring. Because leakage protection devices are installed in home decoration, there will be automatic tripping in the event of leakage or circuit overload.

2. We can rule it out one by one, if it is because of the overload problem in the circuit, you will hear a bang after turning on the light, just like **, it means that the circuit is tripped due to overload. To find the problem of a short circuit, there are three main parts to check. One is that there is a short circuit problem at the place where the live wire and parts are, which can be judged by a multimeter.

3. The second fiber is that there may be a problem of wrong wiring in the bottom box of the lamp, you need to disassemble the lamp, check whether there is a short-circuit problem at the bottom of the light box, or the wrong wiring of the lamp head, you need to remove it to check, if there is a short-circuit or reverse connection, you can directly reconnect it.

Second, there is leakage in the line.

1. There is leakage in the wire, generally speaking, a snap will be heard when tripping, which means that the switch has tripped, which is the sound of tripping, which can be judged to be the leakage of the line. So we need to check the wiring to see if there is a neutral line of the light, or the problem that the socket is connected offline incorrectly. If we find that there is a mix of lines, we can find out the neutral line of the lamp and then arrange it separately.

2. If you find that there is no mixed connection, you can measure its insulation problem, use the shake meter to detect, and then change the line after determining the insulation value.

Summary: As soon as the light is turned on, there is a problem of tripping, it may be that there is a short circuit in the line, or there is a leakage problem in the line. According to these two faults, it is enough to repair it.

Enter the area and get the decoration for free**].

Enter the area and get the decoration for free**].

Summary. In general, there are two reasons, one is that there is a possibility of short circuit or grounding in the wiring of the lamp head. The second is that the air switch (or leakage protection) is damaged. If you don't have basic knowledge of electricians, it is highly recommended that you find a professional electrician to deal with it. Stay safe.

In general, there are two reasons, one is that there is a possibility of short circuit or grounding in the wiring of the lamp head. The second is that the air switch (or leakage protection) is damaged. If you don't have basic knowledge of electricians, it is highly recommended that you find a professional electrician to deal with it. Stay safe.

Hope it helps.

What to do if the bathroom always trips: 1. Poor installation: due to the poor installation of the electric switch, in the case of poor installation of the electric switch, the lead of each pile head will be loosened, and with the passage of time, the fuse will soon be oxidized and burned out, resulting in undervoltage of the line, which will lead to the tripping of the electric switch.

2. Excessive power consumption: If the actual power consumption of household appliances is too large, it will also cause the electric switch to trip, because the rated current of the line is fixed, and if it is exceeded, the load will be automatically cut off. In this case, we need to install a switch with the right amount of electricity used in the home so that it doesn't trip.

3. Leakage and short circuit: If the line in the home leaks, or the electrical appliances leak, it will also cause the line voltage to suddenly become larger, so that there will be tripping. However, this situation is not easy to detect, so it is best to ask a professional electrician to check the electrical and electrical conditions of the home.

There are two main reasons for tripping as soon as the light is turned on: one is that there is a short circuit in the line, and the other is that there is leakage in the line; We can directly rule out the overload situation.

First, let's analyze the situation where there is a short circuit in the line:

If it is a short circuit, we can listen to the sound when the air is tripped, if it is a bang, a bit like the sound of **, that is a short circuit trip;

The short circuit of the lamp circuit is mainly three parts, which we need to check separately;

First, where there is a short circuit between the neutral line and the live line in the line, we can judge it by measuring whether the line is open with a multimeter;

The third is that the switch wiring of the lamp is wrong or the line is shorted, we can disassemble the switch to check, if the wire is found to be short, it can be dealt with; If you find a wiring error, the most common mistake is that the neutral wire enters the switch, which must have tripped and needs to be rewired.

Then let's analyze the leakage in the line:

If it is a line leakage, we can also listen to the sound of the gate tripping, if it is a snap, that is, the sound of the normal tripping of the gate, then the line is leakage;

The first thing to do is to check the line, to see if there is a mixture of the zero line of the lamp and the zero line of the socket, the ground wire, if there is a mixed connection of the line, you need to find out the zero line of the lamp separately, and then arrange it separately;

If we check that we do not find the zero line mixed situation, then we have to measure the insulation of the line, it is recommended that you use the shake meter to detect the insulation value of the line, so that the results are more accurate, to find the leakage of the wire, the only way is to change the line, other methods are to treat the symptoms but not the root cause, it is not recommended to use.

No, the power cord is not involved in heating, so the reason is not the cable. According to the described situation, the previous line almost burned, it is likely that the heating device has been damaged at that time, it is recommended to use a multimeter to measure the resistance of the heating element after power failure.

There should be a short circuit in the line.

6.What is the reason for tripping as soon as the light is turned on? Old electrician: It is important to distinguish these 3 faults!