There are 4 light wires that want to be connected to the surface installation and open five holes, h

You need to insert these 4 light wires directly into a hole, so that you can do it, and the operation method is very simple.

First of all, it is necessary to distinguish each light wire, and also to distinguish the zero line and the wire, and also to determine the location of the installation, to ensure the safety of the circuit, and not to leakage.

Among them should be a neutral wire, a live wire, a ground wire, plus a switch-controlled lighting wire. Connect the neutral live wire and the ground wire first, then jump a wire above the live wire to one end of the switch, and connect the other section of the switch to the remaining one wire to control lighting or other purposes!

Dear, hello, I am glad to answer for you how to connect two light wires to open a five-hole socket Answer: If it is the original two light wires, then there are at least two wires left to open a five-hole socket. It turned out that there were two light wires, one was the fire wire and the other was the control wire. The two worst ones are the neutral line and the guard line.

When connecting the socket and the socket, the control wire will be connected to the switch, the live wire to the socket L wiring hole, the neutral wire to the n wiring hole, and the protection wire to the socket with the grounding mark of the wiring hole. Then connect a wire from the live wire terminal hole to the switch and connect it. However, this wiring method is not safe, because the socket uses a lighting circuit, and the main switch of this line has no leakage device.

It is recommended that you connect three wires from the socket line to the socket.

Kiss! Hello, happy to answer your <>

How to connect two lamp wires to open a five-hole socket The method is as follows: Guess the usage from the one-open five-hole socket used by the subject, that is, which light is fully lit for two rounds, plus a five-hole socket that can be easily used. The neutral wire can connect one of the two light wires to the zero line of the lamp and enter the switch bottom box for the socket.

The lines between the two lamps should be connected to each other. If there is no communication between the two lights, see if the wires of the two lights are threaded into the switch bottom box through the embedded conduit. If so, one of the light wires can be used to lead two wires into the switch bottom box, and the lead will be successful under normal circumstances.

One of them is still used as a lamp line, and one is connected to the zero line of the lamp to be used as the zero line of the socket. If none of the above parts are qualified to be implemented, then you can only do open wires or open walls to break ground to make dark wires, and lead three wires from the nearby socket power supply into the switch bottom box. The reason why three wires are to be introduced, because I don't know the branch of the socket power supply and the lighting power supply and the protection on the branch are empty, if the protection configuration used in the socket power supply back is leakage, and the protection configuration used in the lamp power supply circuit is empty, like this situation, borrowing the live wire on the lighting circuit, the leakage protection configured on the socket power circuit is not powered.

Hope mine can help you <>

Do you have any other questions?

Three open control switch 4 holes, there are 6 wires in the wall light box, how to connect.

The 6 wires are all one color, that is, a power cord, 5 control loops, and the original installation is; The multi-group control switch is first found, the power cord, installed on the triple switch on the wiring hole, the wiring hole of the three switches is connected in parallel, and the book is infiltrated together, and then the control loop of the three lamps is found, respectively, connected to He Mu in Zen Zisen, the lower outlet wiring hole of the three switches can be, The remaining two wires, the wire head is insulated (standby) It is best to ask a professional electrician to connect the live wire in series with a string of wires.

The L hole on the switch and the L hole on the socket are connected to the live wire. The n on the socket is also connected to the zero wire, marked with a hole that conforms to the ground, the ground wire. The switch is marked with L1L2 (different switches have different standards) and the hole is connected to the control line of the lamp.

One of the three holes of the single-open switch is a common point, which is connected to the live wire. The remaining two holes are connected to the control line of the lamp, if you do not consider the direction of the switch lamp, you can connect one at will.

Wire connection is a basic process in the electrical industry, and it is also a very important process. The quality of the wire connection is directly related to whether the entire line can operate safely and reliably for a long time. The basic requirement for wire connection is that the connection is strong and reliable.

Electrician friends must be careful when connecting wires, because if the wires are not connected well, there is a high probability of accidents, resulting in serious losses.

The usual wire joints are connected in this way to ensure that the wire joints do not occur ignition, short circuit, and poor contact. The second connection method of the wire (fireproof tape isolation method), mostly used in the hanging item, or in the relatively high-energy project, the main line can not be broken, the line around the main line for 6-8 weeks, the spotlight in the ceiling, there should be a lot of lights along the way This is the connection, wrapped in the fireproof tape, its role is to prevent the electric fire from burning things, which is very important in the ceiling. The outside is then wrapped with insulating tape.

When wires are connected to switches, fuses and other equipment, special joints must be welded to the wire ends. When a single strand wire or a multi-strand wire with a small cross-section is connected to the terminal of electrical equipment, it can be turned into a small ring sleeve without a special joint, and placed on the terminal of the equipment, with a copper washer and a nut tightened. The direction of the ring sleeve should be consistent with the tightening direction of the screw or nut, so as not to loosen the wire end when tightening the screw or nut.

When connecting two insulated wires, first of all, the insulation of the wire head should be stripped off, the wire core should be wiped clean, and then the wire head should be twisted and welded, and then 2 3 layers of insulating cloth should be wrapped, which can prevent the resistance from increasing and ensure that the insulation strength of the joint is good.

The open-mounted five-hole socket is actually for you to pre-connect the switch into the wire, and the button of the switch must be broken down first with some strength! Then the L-end zero of the live wire access socket is connected to the N-end, the ground wire is connected to the E end, and the lamp wire is connected to L1.

First of all, you need to know whether the switch on the socket panel is a control light or a power outlet. If it is to control a lamp in other places, connect the L (com) end of the switch with the L end of the socket, connect the L1 of the switch with the power cord of the control lamp, connect the N end of the socket with the neutral line of the power supply, and connect the protective grounding wire of the power supply with the grounding symbol of the socket (a total of 4 wires are required).

Professional workers should be invited to install, because the difficulty of installation is also relatively large, so you need to learn some professional knowledge.

Hello dear! We'll be happy to answer for you. How to connect the two light wires to open the five-hole socket Answer, pro:

First of all, let's get to know the five-hole socket, simply put, on the same panel, there is 1 switch, cavity leakage 2+3-hole socket 2, and then turn the five-hole socket over to see its back. You will find letters and symbols 3 that match the LN ground line, L for the fire line, N for the zero line, and the ground symbol for the ground line. The color of the home decoration wire is divided into three kinds of red line (L), blue wire (N) and yellow (ground wire) 4. When the switch is linked to the lamp, the live wire enters the switch, and the zero wire enters the lamp head.

In order to prevent electric shock when changing the bulb, 5, because there are three wires when the wire is routed, sometimes the switch needs to be connected in parallel with the wire, at this time, we must pay attention to the parallel connection of the neutral wire, the live wire and the ground wire. If you have any questions, you can give me feedback in time! Thank you for your patience.

The above is my full reply, if you are satisfied with my service, please give a thumbs up, and I wish you all the best! Peace and joy!

How to connect a single-open five-hole socket with only four binding posts, and the light switch has one binding post, and two wires come out of the bulb.

A single-open five-hole socket, only four binding posts cover Yingqing, the light switch is a binding post, two wires come out of the bulb, how to connect it! Hello, happy to answer your <>

Pro, a single-open five-hole socket, only four binding posts, the light switch is a binding post, two wires from the bulb, the connection method is as follows, there are two open five holes are the socket of the live wire, change, terminals, two for the switch terminal, two terminals of the switch one for the live wire terminal, one for the control wire terminal, the switch live wire can be lent out at the socket live wire terminal access switch live wire terminal. One open five-hole socket with four binding posts. Switch, control socket connects the working neutral wire to the terminal block of n.

The ground wire is connected to the grounding terminal, and the live wire is connected to the end near the gate, so that it is connected, and the switch is turned on. The socket will have power, and when the switch socket is turned off, there will be no power. Switch and control the light, the working neutral wire is connected to the terminal of N, the ground wire is connected to the macro grip ground terminal, and the live wire is connected to the terminal of the socket.

The control line of the lamp, the terminal of the switch. That's it. When the switch is turned on, the light can be on.

When the switch is off, the light goes out. Hope mine can help you <>

Do you have any other questions?