What should I do if the toilet flushes poorly and drains slowly

The first step is to align the toilet drain with a wrench, as shown in the figure below

The second step is to block the sewer mouth of the toilet bowl with force, as shown in the figure below

The third step is to start pumping the toilet bowl without stopping, as shown in the figure below

Fourth, after the dredging is completed, press the flush button and pull out the toilet bowl, as shown in the figure below

First of all, it is necessary to find the cause of the poor flushing, and then prescribe the right treatment. If the water level of the inlet valve is too low, you can disassemble the inlet valve, then take out the buckle of the water valve, rotate the water valve body in the counterclockwise direction, then adjust the height of the body, and finally tighten the water valve body clockwise, and buckle it.

If the toilet is a little blocked and the flush is not smooth, such as a paper towel or rag in it, you need to use a dredging tool to unclog it, or ask a professional master to help. In addition, there will be thick dirt on the inner wall of the toilet after being used for a long time, which will also cause poor flushing. In this case, you should scrape off the dirt and clean the toilet thoroughly so that the flushing is smooth.

The bacteria on the toilet seat can reach thousands, and some bacteria can live for about half a month. Especially in winter, some people like to use toilet gaskets, which are more likely to breed bacteria, so toilet seats are the focus of cleaning, and they should be carefully cleaned and sterilized.

Is there something clogged Find something to open the toilet or find someone to unclog it.

Open the tank and put an empty bottle in it, the purpose is to add buoyancy to the tank to solve the problem.

You can readjust the screw of the clockwise inlet valve, and you will find that the water level can rise quickly, but the water level should not be too full, and it should be about 10 mm away from the overflow nozzle of the drain valve. There are two plastic rods under the toilet water button, and there are cocks on them to adjust the length of the plastic rods to control the amount of water.

The glaze is not good, the glaze is not very good to say, the main thing is to touch it with your hands when you buy it, it is very slippery, there is no graininess, it looks bright and smooth, and it is generally not bad. You can reach into the sewage pipe and touch it, after all, where the glazing better reflects the real level of the manufacturer.

The first step is to align the toilet drain with a wrench, as shown in the figure below

The second step is to block the sewer mouth of the toilet bowl with force, as shown in the figure below

The third step is to start pumping the toilet bowl without stopping, as shown in the figure below

Fourth, after the dredging is completed, press the flush button and pull out the toilet bowl, as shown in the figure below

The toilet drain is not unobstructed and the treatment method is as follows:

1. Many times the toilet flushes more and flushes it by itself, especially if it is a soluble or breakable item such as soil and paper. If it's greasy, then rinse a basin of boiling water to melt it.

Or buy some caustic soda, boil water to melt the caustic soda, pour it into the toilet, and it will be clear in ten minutes. Or use an appropriate amount of oxalic acid to dredge (usually you can also use oxalic acid to clean the toilet, just neutralize with urine alkali to make the toilet unblocked).

2. Use a hook made of wire to stretch into the sewer mouth and stir to make the dirt wrap around the wire, and then pull out the wire to drag the dirt out of the sewer mouth. Or find a half-inch-wide bamboo stick to reach into the toilet bowl to unclog it.

3. Fill half of the toilet bowl with water, use a round mop or a round-headed soft brush, and aim it at the hole in the sewer and pound it vigorously. You can also use the old-fashioned mop and press the hole a few times with the mop after half of the water, moving quickly and relying on pressure to get it through. Or go to the market to buy a puff, and then slam it a few times, use it once every half a month, and it won't be blocked.

4. Use the beverage bottle to dredge, cut off the bottom of the mouth of the large cola bottle after drinking, put it upside down in the toilet, and hold the bottom with your hand and pump it up a few times.

If the toilet paper falls into the toilet, there will be a slight toilet drainage, at this time, you only need to dredge the foreign objects that fell into the toilet; Falling hard objects into the toilet bowl can cause serious blockages, and it is necessary to remove the hard foreign objects from the toilet bowl before entering the water.

Toilet installation mistakes and squatting pit to change the toilet will cause the toilet to drain poorly, and the toilet drain in these two cases needs to be inspected and repaired by professionals.

There can be a variety of reasons why the toilet flushes poorly and drains slowly, and here are some common solutions:

Clean the toilet: If there are paper scraps, hair and other debris in the toilet that clog the drain, you can use a toilet brush or toilet unclog to remove the debris first.

Check the drains: they may be blocked or bent, causing poor water flow. It can be cleaned with a chemical cleaner or a pipe unclogger.

Adjust the flush volume: Some toilets can be adjusted for flushing, and if the flush volume is too large, it may cause the problem of slow drainage. The amount of hail flushing can be appropriately adjusted according to the actual situation.

Check the water tank: The float in the tank can be stuck or damaged, affecting the water level and flush volume. You can check whether the float inside the tank is working properly, and if there is a problem, it needs to be replaced.

Ask a professional to repair it: If the above methods do not solve the problem, it may be that there is a problem with the toilet itself and you need to ask a professional to repair it.

1.Clean the inside of the toilet: Use a toilet brush and detergent to clean the inside of the toilet, especially the water branch and sewer mouth at the bottom of the toilet.

Take the trip 2Use the toilet dredger: Insert the toilet dredge into the inside of the toilet bowl and push down firmly until the air hole at the top of the dredge completely covers the toilet drain, then quickly pull up the dredge and repeat several times until the water runs smoothly.

3.Check the sewer pipes: If neither the internal cleaning nor the unclogging of the toilet does the problem, it may be a clogged sewer pipe.

A sewer drain drain can be used or a professional can be used for inspection and cleaning. 4.Replace the toilet:

If the toilet is aged or damaged, it may need to be replaced with a new one.

<> "What should I do if the toilet flushes slowly and weakly, and the water is slow without a whirlpool."

1. If it is caused by the length of the pressure rod, directly find the position of the pressure rod of the water tank, and then adjust its length to a suitable state.

2. If the dust combustion is caused by the water inlet valve is too low, you can first remove the buckle and rotate it in the counterclockwise direction, then adjust the height, and then rotate back in the clockwise direction, and buckle the buckle, and connect all parts back.

3. If it is caused by too much dirt at the toilet outlet, then you can use baking soda to clean it, and it can be used normally after all the stains are cleaned.

What is the reason for the slow draining of the toilet.

1. The quality of the toilet is not good.

The reason why some toilets will drain slowly is mainly due to quality problems. Because some manufacturers will cut corners in the process of producing toilets in order to seek more benefits, shoddy, and there are some problems in the design itself, so the suction power is not good, and the phenomenon of slow draining occurs when using.

2. The sealing ring of the toilet is damaged, and the sealing is destroyed.

The reason why the toilet can quickly suck away the filth inside is mainly to use the negative pressure inside it, and the sealing ring is one of the key components, if the sealing ring is damaged or aging, then the sealing effect will definitely be affected, the air will enter its interior, and the pressure environment will disappear, and the suction power will definitely decrease.

3. The Ma Xin Duan barrel deviated from the correct position.

If the position of the toilet deviates too much from the original correct position when installing the toilet, and even some parts of the drain are blocked, then it will affect the water flow and the suction power will definitely be insufficient.

Rotate the inlet valve to the right to adjust the height, remove the sealant at the bottom of the toilet, align the toilet drain with the sewage outlet and reinstall and fix it, check the toilet water parts, and replace the damaged water parts.

1. It may be caused by the low water level of the toilet, we can take off the toilet tank cover, take out the inlet valve, rotate the inlet valve to the right to adjust the height, and then install it back.

2. The damage of the toilet seal will reduce the pressure, which will lead to insufficient suction power of the toilet, and the flushing will naturally be weak. We can remove the sealant at the bottom of the toilet, lift the base of the toilet to replace the seal, and then reseal the toilet.

3. The toilet is not installed properly, resulting in a part of the drain being blocked, which will also cause such a problem. You can remove the sealant at the bottom of the toilet, reinstall and fix the toilet drain with the sewage outlet, and then fix the toilet base with glass glue.

4. Damage to the toilet tank accessories will also cause the toilet to flush weakly. You can remove the toilet tank cover, carefully inspect the toilet water parts, and replace the damaged water parts.

When we buy a toilet, we should pay attention to the brand of the toilet. You can consider choosing big brand products such as Wrigley, Jiumu, Faenza, Anwar, Kohler, Huida, etc. When purchasing brand products, we should pay attention to distinguish the authenticity of the product, you can go to the regular store to buy and pay attention to the product anti-counterfeiting trademark, etc., to avoid buying counterfeit products.

When buying a toilet, we have to buy according to the actual situation at home, for example, there is no reserved toilet socket in the bathroom, so you can choose an ordinary toilet. The toilet has a small installation space, and you can choose a wall-hung toilet to save space.