What should I do if the toilet flushes poorly and drains slowly?

Open the tank and put an empty bottle in it, the purpose is to add buoyancy to the tank to solve the problem.

You can readjust the screw of the clockwise inlet valve, and you will find that the water level can rise quickly, but the water level should not be too full, and it should be about 10 mm away from the overflow nozzle of the drain valve. There are two plastic rods under the toilet water button, and there are cocks on them to adjust the length of the plastic rods to control the amount of water.

The glaze is not good, the glaze is not very good to say, the main thing is to touch it with your hands when you buy it, it is very slippery, there is no graininess, it looks bright and smooth, and it is generally not bad. You can reach into the sewage pipe and touch it, after all, where the glazing better reflects the real level of the manufacturer.

The first step is to align the toilet drain with a wrench, as shown in the figure below

The second step is to block the sewer mouth of the toilet bowl with force, as shown in the figure below

The third step is to start pumping the toilet bowl without stopping, as shown in the figure below

Fourth, after the dredging is completed, press the flush button and pull out the toilet bowl, as shown in the figure below

First of all, it is necessary to find the cause of the poor flushing, and then prescribe the right treatment. If the water level of the inlet valve is too low, you can disassemble the inlet valve, then take out the buckle of the water valve, rotate the water valve body in the counterclockwise direction, then adjust the height of the body, and finally tighten the water valve body clockwise, and buckle it.

If the toilet is a little blocked and the flush is not smooth, such as a paper towel or rag in it, you need to use a dredging tool to unclog it, or ask a professional master to help. In addition, there will be thick dirt on the inner wall of the toilet after being used for a long time, which will also cause poor flushing. In this case, you should scrape off the dirt and clean the toilet thoroughly so that the flushing is smooth.

The bacteria on the toilet seat can reach thousands, and some bacteria can live for about half a month. Especially in winter, some people like to use toilet gaskets, which are more likely to breed bacteria, so toilet seats are the focus of cleaning, and they should be carefully cleaned and sterilized.

There can be a variety of reasons why the toilet flushes poorly and drains slowly, and here are some common solutions:

Clean the toilet: If there are paper scraps, hair and other debris in the toilet that clog the drain, you can use a toilet brush or toilet unclog to remove the debris first.

Check the drains: they may be blocked or bent, causing poor water flow. It can be cleaned with a chemical cleaner or a pipe unclogger.

Adjust the flush volume: Some toilets can be adjusted for flushing, and if the flush volume is too large, it may cause the problem of slow drainage. The amount of hail flushing can be appropriately adjusted according to the actual situation.

Check the water tank: The float in the tank can be stuck or damaged, affecting the water level and flush volume. You can check whether the float inside the tank is working properly, and if there is a problem, it needs to be replaced.

Ask a professional to repair it: If the above methods do not solve the problem, it may be that there is a problem with the toilet itself and you need to ask a professional to repair it.

1.Clean the inside of the toilet: Use a toilet brush and detergent to clean the inside of the toilet, especially the water branch and sewer mouth at the bottom of the toilet.

Take the trip 2Use the toilet dredger: Insert the toilet dredge into the inside of the toilet bowl and push down firmly until the air hole at the top of the dredge completely covers the toilet drain, then quickly pull up the dredge and repeat several times until the water runs smoothly.

3.Check the sewer pipes: If neither the internal cleaning nor the unclogging of the toilet does the problem, it may be a clogged sewer pipe.

A sewer drain drain can be used or a professional can be used for inspection and cleaning. 4.Replace the toilet:

If the toilet is aged or damaged, it may need to be replaced with a new one.

<> "What should I do if the toilet flushes slowly and weakly, and the water is slow without a whirlpool."

1. If it is caused by the length of the pressure rod, directly find the position of the pressure rod of the water tank, and then adjust its length to a suitable state.

2. If the dust combustion is caused by the water inlet valve is too low, you can first remove the buckle and rotate it in the counterclockwise direction, then adjust the height, and then rotate back in the clockwise direction, and buckle the buckle, and connect all parts back.

3. If it is caused by too much dirt at the toilet outlet, then you can use baking soda to clean it, and it can be used normally after all the stains are cleaned.

What is the reason for the slow draining of the toilet.

1. The quality of the toilet is not good.

The reason why some toilets will drain slowly is mainly due to quality problems. Because some manufacturers will cut corners in the process of producing toilets in order to seek more benefits, shoddy, and there are some problems in the design itself, so the suction power is not good, and the phenomenon of slow draining occurs when using.

2. The sealing ring of the toilet is damaged, and the sealing is destroyed.

The reason why the toilet can quickly suck away the filth inside is mainly to use the negative pressure inside it, and the sealing ring is one of the key components, if the sealing ring is damaged or aging, then the sealing effect will definitely be affected, the air will enter its interior, and the pressure environment will disappear, and the suction power will definitely decrease.

3. The Ma Xin Duan barrel deviated from the correct position.

If the position of the toilet deviates too much from the original correct position when installing the toilet, and even some parts of the drain are blocked, then it will affect the water flow and the suction power will definitely be insufficient.

1. Accessories are damaged.

The toilet flushes slowly and does not whirlpool, which may be caused by the lack of water in the toilet tank, and the most common situation is that the accessories are loose or damaged. It is recommended to open the water tank, tighten and replace the corresponding accessories, and the problem can be easily solved.

2. The water level of the inlet valve is low.

The low water level of the inlet valve will cause the toilet to flush slowly, weakly, and without a whirlpool. It is recommended to remove the inlet valve, remove the inlet valve buckle, turn the inlet valve body counterclockwise, then adjust the height of the body accordingly, and finally rotate the inlet valve body clockwise. Install the buckle, install the water inlet valve, connect the filter and the water inlet pipe, and the fault will be solved.

3. Toilet quality problems.

If it is a newly bought toilet, there is a problem of slow flushing and no whirlpool, you can consider the quality of the toilet itself, especially some small brands are cheap, due to the unreasonable design of itself, resulting in many problems in use.

What can I do if the toilet flushes poorly and the water is slow:

First of all, if it is a quality problem of the toilet itself, it is recommended to find a professional to debug or replace it; Secondly, if the water level of the water tank is not enough, it is recommended to put an empty bottle in it to improve buoyancy; Finally, if the toilet is blocked, it is recommended to use a leather puff to squeeze it vigorously at the water outlet, or find someone to dredge it.

What are some tips for unclogging the toilet:

1. Use a leather puff or cloth strip mop.

First of all, if the toilet at home is clogged, you can buy a leather pouch, hold the pouch and aim it at the water outlet a few times, or squeeze it with a cloth mop to use the pressure to discharge the dirt.

2. Large Coke bottles.

Secondly, pour a mixture of cola or baking soda and vinegar into the toilet, close the toilet lid, sit on it and press it tightly for a while, and produce gas through chemical reaction to achieve the dredging effect.

3. Spring dredger.

Then, if there is a spring dredge at home, you can insert its small head into the toilet drain, keep rotating the handle, until the spring head goes deep into the deepest part of the pipe, and then pull it back out, so that the dirt can be dragged out and dredged.

4. Hot water + dish soap.

Finally, you can pour it into the toilet bowl to wash it clean, pour hot water at the same time, and then squeeze it with a leather puff to decompose the grease in the pipe, and then press the flush button to dredge the toilet. In addition, you can also use adhesive tape to close the toilet bowl to ensure that there is no air leakage, and then press the water tank switch to put water into the toilet, press it down when the tape bulges, and then release the water and press again, so that the operation can be dredged repeatedly.

Rotate the inlet valve to the right to adjust the height, remove the sealant at the bottom of the toilet, align the toilet drain with the sewage outlet and reinstall and fix it, check the toilet water parts, and replace the damaged water parts.

1. It may be caused by the low water level of the toilet, we can take off the toilet tank cover, take out the inlet valve, rotate the inlet valve to the right to adjust the height, and then install it back.

2. The damage of the toilet seal will reduce the pressure, which will lead to insufficient suction power of the toilet, and the flushing will naturally be weak. We can remove the sealant at the bottom of the toilet, lift the base of the toilet to replace the seal, and then reseal the toilet.

3. The toilet is not installed properly, resulting in a part of the drain being blocked, which will also cause such a problem. You can remove the sealant at the bottom of the toilet, reinstall and fix the toilet drain with the sewage outlet, and then fix the toilet base with glass glue.

4. Damage to the toilet tank accessories will also cause the toilet to flush weakly. You can remove the toilet tank cover, carefully inspect the toilet water parts, and replace the damaged water parts.

When we buy a toilet, we should pay attention to the brand of the toilet. You can consider choosing big brand products such as Wrigley, Jiumu, Faenza, Anwar, Kohler, Huida, etc. When purchasing brand products, we should pay attention to distinguish the authenticity of the product, you can go to the regular store to buy and pay attention to the product anti-counterfeiting trademark, etc., to avoid buying counterfeit products.

When buying a toilet, we have to buy according to the actual situation at home, for example, there is no reserved toilet socket in the bathroom, so you can choose an ordinary toilet. The toilet has a small installation space, and you can choose a wall-hung toilet to save space.

The solution to the toilet drain is not smooth as follows:

You can use caustic soda to dredge it, first melt the alkali with hot water, and then pour it into the toilet, wait for ten minutes, and then the toilet will be unblocked. Steel wire, use steel wire to stir it, you can buy it at the hardware store, the length of the steel wire varies from 1 meter to 3 meters, and the turn can also be stretched in to stir, this method is more effective.

You can also buy a bottle of toilet cleaner, which is more convenient, first pour hot water into the toilet, and then pour an appropriate amount of toilet cleaner into it. After waiting for half an hour, you can use a leather mattress to squeeze and pull out the pipe mouth of the toilet, and the toilet will be cleared, but this product is corrosive, so it is best to wear gloves when using it, and you must pour it carefully.

Daily maintenance method of toilet:

Pour the mixture of vinegar and water into the toilet, soak for half a day, and the dirt will be brushed off; Rubbing the toilet bowl dirt with fine sandpaper removes dirt that cannot be removed by detergents. Sprinkle baking soda on the toilet bowl and brew with hot water for 30 minutes to brush off the dirt; Wipe it with a bleach solution first, and then rinse it off with water after a while.

The flush toilet produces yellow dirt, which is difficult to clean with a brush, so you can tie the used nylon socks to one end of the stick, dip it in foaming detergent to scrub it, and clean it once a month to keep the toilet bowl white. Put an appropriate amount of water in the toilet bowl first, clean it with a toilet brush, then pour in 5-10 ml of detergent or hydrochloric acid solution, apply it evenly with a brush, and then scrub it. If the dirt is heavy, you can pour a little detergent to soak it and brush it until it is clean.

Hydrochloric acid is very corrosive, if you clean it with hydrochloric acid, you should pay attention to safety and do not splash on it.