How to maintain Zippo? What is the introduction of Zippo lighter, and how to maintain it?

No need to take care of it.

As long as you don't fall or touch.

It's okay to play in your pocket or in your hand.

It is a metal lighter, and the maintenance method is as follows.

1. Choose ZIPPO original fuel;

2. When filling oil, pry open the grease nozzle and be sure to break the grease nipple to the bottom end, otherwise there may be oil leakage;

4. Because the ZIPPO special oil is a flammable liquid, you must wipe your hands and the surface of the lighter before lighting the lighter;

5. Check whether the special oil tank has been covered tightly and there is no leakage. Q: How to replace Zippo flint A: Change flint:

Precautions for changing flint:

1. When unscrewing the screw at the bottom of the inner tank, prevent the spring from popping out accidentally;

2. When replacing the new flint, be sure to pour out the old flint fragments;

3. After replacing the new flint, adjust the position of the flint and don't hit the lighter too hard. Q: How to replace the zippo cotton wick A: Change the cotton wick:

2. When loading absorbent cotton, it may not be able to fit in the end, because there are still gaps in the cotton that has been stuffed in, and the application force is solid.

Pinch both sides of the lighter with your fingers (note that the excitation pins are not on both sides) and pull out the movement. Turn the movement upside down, gently lift the lift to fill, and drip the oil onto the cotton ball inside. Fill the cotton ball with oil.

The side of the real zippo lighter cutting flint has two layers of stripes, the upper stripe is an oblique line from the upper right to the lower left, and the lower stripe is an oblique line from the upper left to the lower right, and the intersection of the two lines forms a small diamond-shaped block on the front of the lighter, (because the cost of this process is relatively high, it is difficult to do the same as the real one.) ）

On the right side of the lighter, there are thin stripes radiating from the center to the periphery and evenly spaced, and the stripes are divided into two types, one is a single radial shape, the other is two parallel beams, and two parallel rays are divided into two types. <>

One is that the two lines are arranged very closely, sometimes the unknown swim will think that it is a line when you observe it carefully, and the other is that the two lines are separated by a certain distance and not too far, (this is the current stage of the zippo lighter, there were straight and twill lines before, and I will not discuss it here), the general fake machine also has this kind of small thin line, but these small fine carvings are very irregular, the thickness is different, and it is not as regular as the real machine.

The cotton core is generally changed once a year to two years, and the cotton core is twisted by cotton thread, copper wire, and glass fiber. The consumption is very slow, and the blackened ones are cotton threads, glass fibers and copper wires that are basically not consumed. Don't change very often. If it is burned short, you can cut it off and reload it so that you don't waste it

When you run out of flint, you can change it when you can see that there is still a little left.

The cotton core in the inner tank should be folded into an S or Z shape, and the cotton should be packed according to the shape of the cotton core

After filling up for about a week, it will volatilize if you don't use oil for a long time; In the case of flint, it depends on how you use it, and it will be lost every time you hit it, and a flint can be hit about 500 times; The cotton core does not affect the use and can not be replaced, some can be used for several years, and a cotton core can be cut three times; If you change the cotton core, first put two balls of cotton to fix the cotton core, and then according to the principle of one pressure and one release, you can wind it into an S shape, the cotton should be compacted, otherwise it will not be covered, and the cotton core has nothing to do with the oil, at most it is a waste of oil.

Zippo daily maintenance.

1. How to repair the scratches of the black paint--- where the paint machine will have the phenomenon of paint loss, especially the black cracked paint.

I recommend using Japanese model paint (MR, super clean) as the base, and then apply shoe polish and wait until it dries, and then spray it on top.

If the conditions are not available, a simple repair can be made with a black oil-based marker.

2. There are many friends who ask about the amount of cotton oil lighter refueling, the fundamental reason is whether it is a waste of oil, and how is it appropriate? Let's first understand the absorbent cotton ball, in fact, the absorbent cotton ball is like a sponge, the fiber of the cotton has adsorption to the liquid, and it plays a role in the lighter to fix the oil in the fuselage.

But when refueling, sometimes in order to add more for a period of time, add more, that can only cause waste, when you refuel, due to the influence of the earth's gravity, the oil sinks on the top of the machine (the machine is upside down, that is, the windshield part), the cotton ball can not see the wetness of the oil, if you see the oil wet cotton ball, you add more, the cotton ball adsorbs oil, and there is saturation, then you put the fuselage back into the case, and the bottom of the case will flow out of the oil. Therefore, it is recommended to add less frequently, and the oil volatilizes less in the irrigation, right?

The role of the bottom cotton felt, in fact, is to prevent the oil from flowing out of the cotton ball, the cotton felt is relatively dense, the flow of oil in the cotton felt is blocked, play a role in preventing volatilization, so the problem of volatilization, and the tightness of the fuselage is not big, the example is obvious, the domestic double gun, star, Hong Kong victory and other oil engines, the amount of oil is more than zippo, the reason is the problem of the bottom felt.

If you have a pack and a half of cigarettes a day, you can use two cans of double grab 133ml of electric oil a year, which is less used in winter than in summer, and it is enough to add oil once in about 5 days in summer, but playing trick is another story.

3. If the cotton oil lighter is used for a long time, the flint powder on the steamer and the dirt on the hands will be sweated.

A thick layer of dirt is formed on the surface of the flint, which greatly affects the success rate of ignition, and the dirt layer can be removed with something like a toothbrush and then found after cleaning.

The hot wheel has the feeling when you first bought it, so you can try it.

Just don't throw the machine around, especially the black ice machine, and don't put it together with some hard object, like a key or something. Be careful not to fall. Some machines have chemical reactions, so don't get some other stuff easily.

1. Preparation: a zippo to be cleaned.

A few cotton swabs (5 cents a pack is good), zippo oil.

2. Process: The cotton swab is stained with oil, and all the places in the combustion chamber that are covered by carbon deposits and cannot see the metallic luster.

3. Key points: Be thorough, hard, rub it a few times, and get the flint wheel by the way.

4. If you do a good job, trim the cotton heart again, and its brand new degree will make you excited.

Effect of rubbing copper water to clean zippo:

a. Take out the ZIPPO liner first, clean the dust and dirt on the surface of the jacket with a damp cloth, and dry it.

b. Open the cap of the bottle and pierce and wipe the seal of the copper jug.

c. Shake the jar well, dip it in copper water with a soft cloth, and wait for a while (about 2 3 minutes).After the copper water on the soft cloth is absorbed by the cloth, wipe the fuselage. Pay attention to the uniform force according to the pattern. Wipe in the same direction.

d. Then use a clean damp soft cloth to carefully wipe off the dirt.

Steps 3 and 4 can be repeated several times. until smooth.

f. Polishing with suede.

A few of the more common methods are to gently scrub the surface of the case with toothpaste dipped in water, or wipe with the original oil of Zippo, or use a high concentration of medical alcohol to wipe it down. However, it should be noted that the first method cannot be used for the stamping machine to prevent rust.

Zippo lighter is a very classic brand, you must be out of oil, and there is a long time in the cotton core, you have to change it, otherwise it will block these two situations (if there is no flint, just buy it, yuan a box of 6 pieces).

There is no such thing as a cleaning solution.

It can be cleaned directly with zippo gasoline, and the shell is best wiped with a cotton cloth!

It is best to replace the oil storage cotton after a period of time, otherwise the oil storage capacity will decrease.

Why are you washing it? Do not affect the ignition and do not wash.

You can only wash the inner wall of the shell, use a cotton swab, dip in water or alcohol to scrape a little hard, and then a circle around the flint seat, it is also a cotton swab to wipe on the line, in the combustion chamber, you wash it and then use it or black, don't get the cotton core stained anything, or the cotton core is scattered, you have to rearrange the line when it affects the fire, what do you do with that, zippo is used for use, and don't give it a blind date, is it useful to make it look so good.