Konka LED42R5500FX how to connect to the wireless network

Konka LED42R5500FX TV is an Android smart TV, which can directly set up a wireless network to connect to the wifi signal of the router at home. Here's how:

1. Start the TV and enter the main interface of the TV;

2. Find [System Settings] and press the confirm button to enter;

3. After entering the [System Settings] interface, find [Wireless Network Settings] and press the confirm button to enter;

4. After entering, turn on the wireless network connection, search for the nearby wifi signal, find the wifi signal sent by the wireless router at home, click to connect, enter the wifi password, and the connection can be established;

Dear users, hello!

Thank you for your attention and support. This TV network wireless network,First check the characteristics of the machine's random manual,Whether the machine is marked with built-in wifi function,If the machine does not have built-in wifi function,Wireless networking needs to be connected to an external wireless network card and wireless router。

The TV has requirements for the chip model of the wireless network card, and the chip model of the wireless network card that needs to be purchased is RTL8192CU, RTL8188CTV, RTL8188CUS, and there is no restriction on the brand and model (if the machine has built-in WiFi, it does not need to be connected to an external wireless network card).

The TV also has requirements for the setting of the wireless router,It is recommended to set it in the following way:Use WPA encryption,Password type is selected TKIP,PSK EAP is selected PSK,Password needs to be set8 digits (password is recommended to use numbers 0-9 TV is easy to identify)。 After the router is set up, select the wireless settings of the TV, enter the password, and automatically obtain the IP address, and the connection is successful.

Successfully connected to the Wi-Fi, I still can't watch TV.

Konka led50r5100de TV how to connect to the network cable to the Internet, no CCTV, there is a router, detailed operation, thank you.

Hello, I'm glad to answer for you The following is the answer to the answer, please take a look, first, wired connection, please operate as follows: 1. Wired connection needs to match: router, network cable, computer, network TV; 2. First of all, the router and the computer can be connected to the network normally (please set the IP of the computer to automatically obtain first; After that, connect the computer and the router), and then connect one end of the network cable to the router and the other end to the network interface of the TV; 3. TV menu - network settings - wired settings, IP type Select automatic get, and finally click Settings.

2. Wireless connection, please operate as follows: 1. Wireless connection needs to match: wireless network card, wireless router, computer, network TV 2, wireless router and computer can be connected to the network normally, please connect the wireless network card to the TV; 3. TV menu-Network Settings-Wireless Settings-SSID(Search for router devices)、Encryption type(Same as set on the computer)、IP typeSelect automatic getting,Finally, click Settings。

3. When the wireless connection cannot be connected, pay attention: 1. Please confirm that the wireless router and wireless network card used are normal and can be used 2. The signal strength of the wireless network is too low (when the wireless network strength you use is less than 35%, although our machine can detect the network, it cannot be successfully connected.) In order to ensure the normal use of the wireless network, the signal strength is required to be stable at more than 70% or more than two bars.

3. When there is a wireless connection, you can search for the signal, but the connection fails, you need to check: encryption type, WEP length, and whether the WEP mode settings are correct. Please confirm the parameters set by the encryption method,Our TV can be recognized normally:

a) Use WEP encryption mode, set as follows: open for authentication mode, 64bit for wep encryption, ASCII for key mode, any one key can be set, and the password needs to be set to 5 digits. (b) WPA encryption is adopted, and the settings are as follows:

Set the password type to TKIP, select psk for PSK EAP, and set 8 digits for the password. (Note: The password is recommended to use the numbers 0-9 for easy identification of TV).

Konka LCD TV LED46F5580F How to connect to a wired network:

Connect the network cable from the router to the network port on the back panel of the TV, open the network settings of the TV, and automatically obtain the IP address when it is successful, and connect to the network.

P.S. The specific steps for setting up a wireless network are as follows:

1. Press the "Menu" button of the TV remote control to find the "System" option;

2. Find "Network Settings" in the system menu and enter;

3. Click "WiFi Switch" to open, as shown below, and enter the wireless connection settings;

4. Click to open the wireless wifi network page after a lot of wireless network names will appear, find your own wireless network click to enter;

5. Enter the correct password of the wireless route to open the wireless network;

6. Successfully connected to the wireless network.

1. Wired connections need to match: routers, network cables, computers, and network TVs; 2. First of all, the router and the computer can be connected to the network normally (please set the IP of the computer to automatically obtain first; After that, connect the computer and the router), and then connect one end of the network cable to the router and the other end to the network interface of the TV; 3. TV menu - network settings - wired settings, IP type Select automatic get, and finally click Settings. Thank you for your consultation and have a great day!

Do you want this TV to act as a monitor? Then you buy a longer VGA cable. Connect directly to a computer monitor. There is a VGA interface in the back. In addition, adjust the signal source to VGA on the TV.

Dear Konka users:

Hello, thank you for your support to Konka products! LED55M3500PDF is Konka's third-generation network TV, the TV supports Internet connection, and users can use "wired networking" or "wireless networking" to connect to the network.

For wired connection, please do the following:

1. Wired connection needs to match: router, network cable, computer, network TV;

2. First of all, the router and the computer can be connected to the network normally (please set the IP of the computer to automatically obtain first; After that, connect the computer and the router), and then connect one end of the network cable to the router, and the other end to the network interface of the TV stool;

3. TV menu - network settings - wired settings, IP type Select automatic get, and finally click Settings.

Wireless connection, please do the following:

1. The wireless connection needs to be matched: wireless network card (it is recommended to use RTL8191SU, RTL3070, RTL8712 as the main chip of the wireless network card, drive-free, plug and play; If the TV has a built-in wifi function, it is no longer necessary to configure a wireless network card), a wireless router, a computer, and an IP TV.

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV;

3. TV Settings - Network - Wireless Settings - SSID (Search for Router Devices), Encryption Type (the same as set on the computer), IP Type Select automatic acquisition, and finally click Settings.

4. If it is a built-in wifi function, set - network - wireless settings, turn on wifi, select the name of your router, a dialog box will pop up, prompting you to fill in the password, please use the Konka remote control keyboard and mouse to enter the input. After entering, click Connect and then click Network Detection. If the TV prompts that the network has been restored and the network is connected, it means that the TV has been successfully connected to the Internet!