Little Swan automatic washing machine put in the clothes when the drainage is not smooth when it is

When encountering a failure of the washing machine with poor drainage or no drainage, do not rush to judge whether the washing machine is faulty. You should first check whether the drain pipe of the washing machine is lowered and whether the water outlet is too high, and the water outlet should be lower than that of the washing machine, so that the water can be drained normally, otherwise there may be water accumulation. If all of the above conditions are normal, then check the cause of the failure of the washing machine's drainage system.

After inspection, it can be found that the main reasons for the failure of the washing machine drainage system are as follows:

1. The drain pipe is twisted, and only by keeping the drain pipe unblocked can the washing machine drain normally. The drain can be rearranged or replaced.

2. When the drainage is slow, it may be because the drain port is too high and the tension spring strength of the drain valve is not enough, so that the valve core is opened. The drain can be lowered and the tension spring can be replaced to solve the problem.

3. Open the back cover of the washing machine and check whether the drain valve pull strap falls off, and whether the valve pull belt or drain pull rod is broken and blocked.

4. Check whether the drain filter and drain valve in the barrel are blocked by debris, causing slow drainage or even no drainage. It is possible that the dirty material of the clothes is blocking the drain. At this time, the drain filter should be removed for cleaning, and the drain should be flushed with water and the debris in the drain valve should be removed.

If the drain of the automatic washing machine fails, it can be repaired according to the following methods:

a. Start the washing machine program after selecting the single dehydration program, and listen to whether the drain electromagnet has a "pop" suction sound. If there is a suction sound, it means that the drain solenoid is properly engaged, and the drain valve may be blocked;

b. The drain valve tension spring falls off or is corroded and broken, and the damaged parts need to be cleaned and replaced.

c. If there is no suction sound of the drain solenoid, the rear cover plate should be opened to check whether the drain solenoid plug-in wire falls off, if it falls off, it can be used after re-insertion. If it does not fall off, you can use a multimeter to measure the resistance of the two terminals of the drain solenoid, if the resistance value is infinity or less than 30 ohms, it means that the drain solenoid has been broken or short-circuited, and should be replaced.

d. If it still does not work normally after replacement, it may cause the failure of the program controller due to the burning of the drainage electromagnet (generally the thyristor that controls the drainage), and the controller needs to be overhauled.

Most of the reasons why the washing machine drain system compensates or does not drain water are caused by clogged swag in the drain pipe. When using the washing machine, you should pay more attention to the maintenance of the washing machine, so as to avoid the phenomenon of poor drainage of the washing machine.

The most common is the blockage of drainage, such as: socks, coins, cotton wool, napkins, etc.

Only by disassembling the machine and cleaning it can it be used normally, otherwise it will get more and more serious.

The drain shut-off valve is damaged.

Little Swan washing machine has the characteristics of convenience, cleanliness, function and environmental protection.

In 2010, the first washing machine product with automatic detergent added was launched in China, and 4 new washing machines with automatic detergent were launched for Little Swan, including 2 Yixuan series washing machines and 2 Zhizhen series drum washing machines.

It has been identified by the most authoritative ** institutions and expert teams. On November 28, 2010, in the appraisal and acceptance of new technologies and new products organized by the appraisal committee organized by the Jiangsu Provincial Economic and Information Commission, 2 Yixuan wave wheels and 2 Zhizhen rollers of Little Swan passed the acceptance. The appraisal committee unanimously agreed that the above four Little Swan products have reached the international advanced level, and the automatic detergent addition technology adopted by them is the first in China.

On September 1, 2011, the "automatic detergent" technology adopted by Little Swan automatic washing machine won the technological innovation award of the 2011 China Household Appliance Innovation Award by virtue of the innovative breakthrough of intelligent technology.

On March 20, 2012, at the China Home Appliance Expo held in Shanghai, Little Swan Washing Machine released a full range of IADD automatic washing machine products, covering 11 products in 4 series of drum and wave wheel, becoming the first enterprise to realize the upgrade of the whole line of products.

The Little Swan washing machine has been flooded all the time, and there should be a problem with the water level switch of the washing machine.

If the power of the washing machine is turned on, the water level switch has been set, and the washing program is set, the washing machine will be started at this time, and the water inlet solenoid valve will start filling water.

If the solenoid inlet valve is filling and reaches the set water level (or keeps refilling) and the washing machine does not start washing, then there is a problem with the water level switch of the washing machine.

It is recommended to contact the after-sales service department of the washing machine for repair.

After the Little Swan washing machine is filled with water, the water flows out of the drain pipe, and the reason for the continuous drainage should be that there is a problem with the drain valve of the washing machine.

If the drain valve is not closed tightly, water will flow out after filling and during normal use. It is necessary to check whether the drain spool is reset.

It is recommended to contact the after-sales service department of the Little Swan washing machine according to the brand and model of the washing machine, and repair and inspect the drainage system of the washing machine or clean the drain valve.

Summary. This phenomenon is generally the failure of the drain valve, which is not tightly closed, because the washing machine must be washed to the set water level, if it cannot be reached, it will not be washed, and dehydration, as long as the minimum water level is reached, it can work.

It is recommended to disassemble the back cover, and then check the drain valve, if there is a dirty blockage, just clean it up, if there is a problem with the seal, it is recommended to replace the seal.

Still no, only to replace the drain solenoid valve.

The Little Swan automatic washing machine always puts water and doesn't wash clothes, what's going on?

This phenomenon is generally the failure of the drain valve, not tightly closed, because the washing machine must be washed to the set water level, if it can not reach the portable smart file, it will not wash the wide side, and dehydration, as long as the minimum water level is reached, it can work. It is recommended to disassemble the back cover, and then check the drain valve, if there is a dirty blockage, clean it up, and if there is a problem with the seal, it is recommended to replace the seal. Still no, only to replace the drain solenoid valve.

The water level is already high, it just doesn't work.

It is recommended to make trouble in time and ask the maintenance master to come to the door for maintenance and troubleshooting. 1. Check whether there are foreign objects (coins, brooches, buttons, etc.) stuck in the opening of the drain valve bend, resulting in the drain valve core not returning to the position, unable to close the water and flushing the drain at the edge of the water inlet, and the solution is to take out the foreign body. 2. Check that the drainage tractor (drainage motor) is faulty, and the drainage cable does not return, resulting in drainage while entering the water, and the solution is to replace the drainage tractor.

3. Check the failure of the water level switch or water level sensor, the water level pressure cannot be sensed, resulting in drainage while entering the water, and the solution is to replace the water level switch or water level sensor. 4. Check that the water pressure air guide pipe is broken or loose, and the pressure to water level switch or water level sensor cannot be provided, resulting in drainage while entering the water, and the solution is to adjust and replace the water pressure air guide pipe. 5. Check whether the central shaft is leaking, and it is easy to burn out the motor.

Summary. Dear, hello, I'm glad to answer for you, what is the reason why the little swan washing machine does not dry after draining the water?

Answer: The Little Swan washing machine does not dry after draining the water is the first reason: the clothes are unbalanced.

When the washing cannot be adjusted to balance, the washing machine automatically sets a low speed, at which the dehydration effect is slightly worse.

Reason 2: The switch of the top cover is damaged.

The washing machine is not allowed to open the top cover because it is a high-speed action when spinning, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the lid is opened. If it is damaged and dehydrated, it will not move!

Reason 3: The texture of the clothing.

It is recommended to use high-speed dehydration for washing products with strong water absorption (high-speed dehydration cannot be used for some high-end clothes).

Reason 4: Clogged drainage system.

What is the reason why the little swan washing machine does not dry up after draining the water.

Dear, hello, I'm glad to answer for you, what is the reason why the little swan washing machine does not dry after draining the water? Answer: The Little Swan washing machine does not dry after draining the water is the first reason: the clothes are unbalanced.

When the washing cannot be adjusted to balance, the washing machine will set a low speed with a self-grasping pulse, at which the dehydration effect will be slightly worse. Reason 2: The switch of the top cover is damaged.

The laundry Duanxiang machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover is opened. If it is damaged and dehydrated, it will not move! Reason three:

Clothing materially. High-speed dehydration is recommended for washing products with strong water absorption (high-speed dehydration cannot be used for some high-profile clothes). Reason 4:

The drainage system is clogged.

Thank you for your patience. The above is my full reply, do you have any other questions? I can continue to answer your questions, I hope this service can help you, you can click on my avatar to follow me, and if you have any questions in the future, you can consult me again, and look forward to serving you at this time.

Wishing you well; Have a good life and all the best! If you are satisfied with my service, please give a thumbs up, and once again wish you all the best! Peace and joy.

What is the reason why the Little Swan automatic washing machine is running normally without load, and the laundry is drained?

Hello dear, I have helped you find the result; The Little Swan automatic washing machine runs normally without load, and the reasons for the drainage of laundry are as follows:1Water Leakage:

The bottom of the washing machine is leaking, causing the washing machine to drain. Please check the bottom of the washing machine for signs of water leakage. 2.

3.Drain Pump Problem: The Tongbi drain pump is not working properly, causing the washing machine to drain while doing laundry.

There was a problem with the washing machine control panel, causing the washing machine to drain while doing laundry. Please contact the maintenance personnel to inspect the control board. The above is all my reply, I hope I can help you, thank you for your consultation.

Reasons: 1. There is a problem with the drain valve of the washing machine, the drain valve is not closed tightly, and the water will flow out after water injection and normal use, and it is necessary to check whether the drain valve core is reset; And late.

2. The drain valve is stuck by dirt or hard objects, and loses its function of controlling drainage, resulting in the drain valve core cannot be returned to the washing machine to drain water while filling water;

3. Check that the drainage tractor is faulty, and the drainage cable does not return, resulting in continuous drainage.