What happens if the clothes are washed in the automatic washing machine?

1.You put the washing machine in the washing state and he starts to wash the clothes, and when the washing machine is spin dry, he can only do one job, not two jobs. Therefore, you can't wash your clothes when you spin dry, and if the washing machine can only spin dry and can't wash clothes, it means that the motor is broken and call a professional to repair it.

2.The reason why the automatic washing machine can wash clothes without dehydration and how to deal with it:

1) Whether the laundry is seriously biased to the side of the dehydration bucket, or the laundry is placed too much and the dehydration bucket does not work.

2) The plug of the door closure switch is not in good contact, and whether the connectors and wires are normal - it is more likely.

3) Check whether there is any foreign object between the dehydration bucket and the water bucket.

4) If the V-belt is too loose or falls off, the belt can be adjusted or replaced.

5) The large oil seal is not installed properly and jams the dehydration shaft. (Generally, it is easy to occur after replacing the large oil seal during maintenance) 6) The brake belt is not loosened.

7) Program control board failure.

8) The drain valve is blocked, which will also cause no dehydration. It is advisable to clean up the drain valves and drain pipes.

The unbalanced laundry is caused by the non-dehydration of the automatic washing machine: when the washing cannot be adjusted to the balance, the washing machine will automatically set a low speed, at which the dehydration effect will be slightly worse.

The switch of the top cover of the automatic washing machine is damaged because it is a high-speed action when dehydrating, and the top cover is not allowed to be opened, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened. If it is damaged, it will not move.

The reason for the non-dehydration of the automatic washing machine is that the laundry is material: it is recommended to use high-speed dehydration for washing with strong water absorption (high-speed dehydration cannot be used for some high-end clothes).

Our washing machine can't be shaken off after washing and dehydrating, only the alarm sound of washing is heard, what is going on, please explain the fault'

Causes and treatment methods of automatic washing machine dehydration and drying:

1. There are many situations in which dehydration does not dry, such as the dehydration capacitance capacity decreases, and dehydration cannot enter the high speed.

2. The belt is too loose, and the pulley will slip at high speed, so the dehydration is weak.

3. The drainage is not smooth, the drainage pipeline is blocked, although the drainage is drained, but it is not discharged, and the clothes are soaked again after stopping.

4. The wear diameter of the clutch square wire torsion spring becomes larger and rusty, so that the square wire torsion spring cannot hold the dehydration shaft to drive the normal operation of the dehydration barrel, resulting in dehydration weakness.

5. The drain valve is not fully opened, the drain valve is blocked, and the drain is slow.

The washing process of the washing machine is mainly to pull the dirt into the water to achieve the purpose of washing under the mechanical action of mechanical action such as infiltration and scouring generated by machinery and the wetting and dispersion of detergent. First, the washing liquid filled between the blades of the wave wheel is thrown at high speed against the wall of the barrel under the action of centrifugal force, and rises along the wall of the barrel. At the center of the wheel, a low-pressure zone is formed due to the liquid being thrown out, which in turn causes the scrubbing liquid to flow back to the vicinity of the wheel.

In this way, an eddy current centered on the axis of the wave wheel is formed near the wave wheel. Under the action of vortex, the clothes rotate in a spiral shape, and after being sucked into the center, they are thrown against the wall of the barrel and rubbed against the wall of the barrel. In addition, because the center of the wave wheel is a low-pressure area, the clothes are easy to be sucked near the wave wheel, and constantly rub against the wave wheel, just like manually rubbing clothes, and the dirt is forced to leave the clothes.

Secondly, when the laundry is put into the washing liquid, due to the slow movement of inertia, there is a velocity difference between the water flow and the laundry, so that the two move relatively, and the water flow and the laundry will be relatively rubbed, and this water scouring force also helps the dirt to leave the laundry. Again due to the irregularity of the shape of the laundry spring.

When the swirling water hits the wall of the barrel, its speed and direction change, resulting in turbulence. Under the action of turbulence, the clothes move irregularly and tumble, and their fibers are constantly bent and elongated, and the clothes rub against each other, which increases the effective area of washing and improves the uniformity of washing clothes.

1. The laundry is normal, and the clothes are always not dry, depending on whether the dehydration is normal.

2. The spinning speed of the washing machine is around 700 rpm, if the speed is okay and it is not dry, it depends on whether the spinning time is enough for 3 minutes and 5 minutes, and whether the clothes are around the barrel wall.

3. The selected dehydration speed is too low, generally Siemens has a speed selection button, and the speed is adjustable from 400-1600. If you choose a low speed, the dehydration effect will not be good.

4. If you choose a different washing program, it will also change the spinning speed: for normal cotton clothes, the maximum speed is set by default in the washing machine program. When wool is washed, it is generally dehydrated at the end, and the lowest gear is chosen to prevent the sweater from shrinking.

If there is a feather clothing lotion, the general dehydration speed will be set at 800-1000 rpm. So, there will also be a different dryness experience.

There are several reasons that can cause this problem:

1) The selected dehydration speed is too low, generally Siemens has a speed selection button, and the speed is adjustable from 400-1600. If you choose a low speed, of course, the dehydration effect is not good.

2) If you choose a different washing program, the dewatering speed will also be changed.

Setting of the additional washing machine

1. For normal cotton clothes, the maximum speed is set by default in the washing machine program.

2. Wool washing, generally the last dehydration, will choose the lowest gear to prevent the sweater from shrinking.

3. If there is a down jacket to wash, the general dehydration speed will be set at 800-1000 rpm.

4. In order to allow users to have a better experience of dryness, all washing programs can adjust the dehydration speed by themselves. After selecting the main washing program, the user can press the speed adjustment button to adjust the speed independently.

Slow to ask questions.

The landlord has explained that the laundry is normal, and the clothes are always dry:

Then it depends on whether the dehydration is normal, the dehydration speed of the washing machine is around 700 rpm, if the speed is okay and the spin is not dry, it depends on whether the dehydration rotation time is enough for 3 minutes 5 minutes, whether the clothes are around the barrel wall, if it is all right, it is the moisture content of the clothes themselves.

If dehydration is not normal:

If the speed is abnormal, you can find the problem from the belt, capacitor aging, traction device and clutch;

If you don't have enough time to dehydrate, it's a problem with the program.

There are two types of automatic washing machines: wave wheel type and drum type, which form is yours? The biggest disadvantage of a front-loading washing machine is that it does not dry the clothes, but it has the least wear and tear on the clothes. If you are a wave wheel type, there is something wrong with the clothes that don't dry, and you can notify the after-sales service to check it.

1. The speed of the motor slows down, and the capacitor capacity becomes smaller; 2. The motor is stuck; 3. The motor is faulty; 4. The brake of the washing machine does not pop on; 5. The drain port of the washing machine is blocked.

1. There are too many clothes and clothes in the washing machine to be dehydrated, which means that the capacitance capacity of the motor starts to decrease. Replace the envy with the same capacity and the problem is solved. The starting winding of the dewatering bucket motor is connected in series with a capacitor of about 4 F to improve the starting characteristics of the motor.

After the power supply of the washing machine is turned on, the motor of the dehydration bucket makes a "buzzing" sound without destroying the rotation, the power plug should be unplugged, check whether the capacitor is invalid, and it can also be replaced with a new product; If the motor starts running normally, the fault is on the capacitor. 2. If the belt is too loose, check the belt.

1. Unbalanced clothing.

When the washing cannot be adjusted to balance, the washing machine automatically sets a low speed, at which the dehydration effect is slightly worse.

2. The switch of the top cover is damaged.

The washing machine is not allowed to open the top cover because it is a high-speed action when spinning, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the lid is opened. If it is damaged, it will not move.

3. The reason for the texture of the clothing.

It is recommended to use high-speed dehydration for washing products with strong water absorption (high-speed dehydration cannot be used for some high-end clothes).

4. The drainage system is blocked.

The washing liquid in the water cylinder can not be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

5. The water level switch cannot be reset.

The dewatering process of the fully automatic washing machine starts with the water level switch reset after the washing liquid has been drained. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, the dewatering procedure will not be entered.

Hello, it is a pleasure to serve you, your question is being queried, please wait for a while

What is the reason why the automatic washing machine does not dehydrate: the drain pipe is blocked or the drain solenoid valve is faulty; Check whether the adjusting rod nut on the drain valve is loose, resulting in the retractor being unable to pull the drain valve core apart and causing non-drainage, fix the nut at this time so that it can open the drain valve core; What is the reason why the automatic washing machine is not dehydrated1, the computer board may be damaged, and the computer board is not drained due to the problem of the computer board, and the computer board usually needs to be overhauled or replaced. 2. If the brake is not released, the motor cannot be started due to too much load, and the buzzing sound can be heard at this time, and the drain pull rod can be adjusted.

3. Some models should check whether the tractor cable is loose from the drain valve; If the nut is not loose or the cable is not loose, the retractor may be damaged and cannot open the drain spool, at which point the retractor should be replaced. 4. If there is no drainage, it may be that the drain valve coil is burned out. 5. The clutch problem causes no drainage, which needs to be repaired or replaced.

6. There may be debris in the drain valve that is blocked and causes non-drainage, open the back cover of the washing machine, make the washing machine enter the dehydration program, and observe whether the drain valve is pulled apart by the tractor, if not, it may be a computer board failure or a tractor failure; If you observe that the drain valve core is pulled open, but does not drain, it is a blockage of the drain pipe, and in most cases, the drain valve inlet is blocked, and the debris can be removed to eliminate the fault.

The reason why the washing machine can not be dehydrated is usually due to the poor contact caused by the ablation of the safety switch contacts in the cover, or the switch is caused by wear and displacement, the cover should be disassembled to view, if the contacts are ablated, you can use fine sandpaper to polish the brightness. If the switch is worn or displaced, it is best to replace it with a new switch of the same specification.

Check whether the mode is normal first, and then check the water level sensor, door cover switch, safety switch, traction motor, general bearing, and computer control board.

Check first whether you have adjusted it to the dehydration mode, if there is a choice or not, then it means that there is a problem with the system to be repaired.

The main reasons why automatic washing machines can't dry clothes are:

1. The balance device of the washing machine is faulty, resulting in the imbalance of the clothes in the washing machine, so there is no way to reach the highest speed when spinning the clothes, and the moisture of the clothes cannot be dried.

Second, the material of the clothes is not suitable for automatic washing machine to clean, and some clothes are not suitable for washing machine to dry, for example, the down jacket may be inflated in the process of water drying, and it is difficult to balance the washing machine's spinning bucket after the down jacket sprints, so the clothes after spinning off still have a large moisture content.

3. The speed of the washing machine is too slow. The main reason is that the motor performance of the washing machine is aging or the capacitance capacity of the washing machine motor is insufficient, resulting in the speed of the washing machine motor not reaching the standard, so when the clothes are dried, the corresponding performance cannot be achieved.

There may be several reasons why clothes can't be thrown off in a fully automatic washing machine:

1.Overloaded washing machine: If there is too much laundry in the washing machine, it will lead to poor spinning results. Therefore, when using the washing machine, you should choose the right amount of clothes according to the capacity of the washing machine to avoid overloading.

2.Insufficient centrifugal force in the washing machine: Insufficient centrifugal force in the washing machine can also lead to poor spinning results. If the centrifugal force of the washing machine is not enough, you can try adjusting the speed of the washing machine or choosing a higher centrifugal force mode.

3.Unbalanced washing machine base: If the washing machine base is unbalanced, it will also lead to poor spin drying. You can use a spirit level to check if the washing machine is level, and if it is not balanced, you can adjust the floor mat of the washing machine or use a mat to balance the washing machine.

4.Washing machine drum failure: If the washing machine drum fails, it can also lead to poor spin drying. The washing machine drum can be inspected for foreign objects stuck or if parts need to be replaced.

5.Washing machine for too long: If the washing machine is used for too long, it will also lead to poor spinning results. Consider replacing the washing machine with a new one.

In short, there may be a variety of reasons why clothes in automatic washing machines do not dry all the time, and they need to be investigated and solved according to the specific situation. If you can't solve it by yourself, it is recommended to contact a professional maintenance personnel for overhaul and repair.

If your laundry is not dry after several spins or has too much moisture after washing in your automatic washing machine, it may be caused by several reasons:

The washing machine is overloaded.

When you add too much clothing to the washing machine, the water may not flow out quickly and finish well spun drying, making it difficult for the washing machine to perform at its best. It is advisable to follow the instructions on the instructions for maximum loads to add the appropriate amount of clothing.

Filter blockage or dirt build-up.

Clogged filters or dirt build-up in the washing machine can also affect its spin-off effect. Regular inspection and cleaning of the filter can solve this problem and improve the spin-off efficiency of the washing machine.

The washing machine is unstable or vibrating.

Vibration or tilting of the washing machine during spinning can also affect the spin drying effect. When using the washing machine, make sure it is against a wall and there are no obstacles around it to avoid the machine shaking.

The bottom of the washing machine is not properly placed.

If you've just moved into a new home and installed a fully automatic washing machine, you'll want to check if you need to adjust the bottom of the washing machine smoothly so that it doesn't sit uncomfortably and vibrate. If the problem still occurs, you may need to inspect and replace the individual parts of your washing machine.

In conclusion, if your fully automatic washing machine is not able to dry laundry effectively, first make sure that the load is just right, the filter is clean, the machine is stable, and the requirements in the instruction manual are followed. If the problem persists, it is advisable to seek professional help to diagnose and resolve the issue.