-
Anonymous users2024-02-11The frequency doubling of Intel's CPU is locked, so you can only super-clock and adjust the external frequency up little by little, step by step!
In addition, you should also be clear about whether your CPU has a good physique, and the CPU with a bad physique has little overclocking potential, don't be too greedy, assuming your CPU frequency, it's good to overclock. If you burn overclocking, you're asking for trouble! This may result in the loss of Intel's warranty service!
Be careful, heat dissipation should be strengthened!! When the CPU temperature reaches 80 degrees Celsius, don't go any further! No matter how over, it may burn! In addition, it is possible to overclock to a higher frequency with a voltage, but it is not recommended!
Note: After the motherboard logo screen appears at boot, press the delete key to enter the CPU in the BIOS of the motherboard
frequency regulates voltage and external frequency.
Observe the voltage and CPU temperature in PCHiant.
-
Anonymous users2024-02-10In the BIOS, set the DDR Dual Channel Function option to "Enable".
-
Anonymous users2024-02-09It proves that this motherboard supports dual channels, generally add a memory module and reboot it, if the memory is not compatible, replace it with another brand of memory module.
-
Anonymous users2024-02-08When replacing hardware on an old computer, you need to learn simple troubleshooting.
Generally, if you replace the hardware and don't light up, first reseat the memory and try it, if it doesn't work, check the graphics card, if it still doesn't work, then change back to the original CPU to see if it can boot normally, if you switch back and forth on the e5500 point is not lit, then it may be a CPU problem or a motherboard BIOS problem.
When changing the CPU for testing, you can not use silicone grease first, just put the radiator, and then install the radiator after lighting it normally.
-
Anonymous users2024-02-071. First of all, overclocking depends on whether the motherboard and CPU can support it, and the E5500 can be overclocked, it depends on the motherboard.
2. Overclocking method: Overclocking can be done through the motherboard BIOS. Press the DEL button to enter the motherboard BIOS when you boot up; After entering the BIOS;
Enter Advanced Mode; Select AI Tweaker (change overclocking); Select the AI Overclock Tuner; Set auto to manual.
3. Overclocking: In the following values, live a little bit and add it, and add it to the main frequency above when it becomes the same as you want it (this is the super frequency, the memory will automatically follow the super, and the frequency doubling and voltage do not need to be set) generally do not exceed too high, otherwise you will not be able to enter the system;
4. Adjust to the appropriate frequency, press F10 to determine the exit.
-
Anonymous users2024-02-06In this case, you need to replace a motherboard to try it, which may be caused by the current motherboard not supporting it.
-
Anonymous users2024-02-05This board does not seem to support fan voltage adjustment, so it is not possible to slow down the fan.
The 4500r is too high, the 3000 is fine.
Add a resistor to the line of the fan by yourself, and the partial voltage will do.
As for how big it is, it depends on the fan model.
How does bank wealth management compare with P2P wealth management? >>>More
The effect is almost the same, mainly used in the rental market 500*1000mm cabinet, P3 is a conventional screen.
The Philips box of the American Bank is marked with the brand Norelco, and the European Bank uses the same logo as the domestic licensed goods: Philips, and there is no difference as for the shaver itself. But the national bank. >>>More
PLC is a programmable controller.
The i3 330M definitely has an advantage, mainly because the clock speed is slightly higher (P6100 is 2GHz, 330M is another i3 330M supports four threads and 4MB of L3 cache, which are obvious advantages).