-
Error analysis: It is generally caused by an error in the disk, sometimes it is also recommended to check whether the hard disk connection is not in good contact, or does not use a cable that meets the transmission specifications of the hard disk, for example, the ATA-100 still uses the ATA-33 cable, which does not matter to the low-speed hard disk, but tells the hard disk (supports ATA-66 or above) The requirements are stricter, and the connection with the wrong specification will sometimes cause this kind of failure to boot. If this error still occurs frequently after repair, it is likely to be a precursor to hard drive corruption.
Solution: In general, a reboot will resolve the issue, and it is recommended to do so anyway"chkdsk /r"command to check the repaired hard drive.
To supplement your supplementary questions, you first use the software I introduced above to detect and see, if it is determined that there are bad sectors, you can only low-format the hard disk. There is a 70% chance that it will be repaired and it will work normally.
Low format if you don't understand. You can go to the maintenance point to make people low, up to 20 yuan.
Remember to save the data to a different hard drive first. Otherwise it will be gone.
-
Notice that the sound of your computer's hard drive is different from the original? If there is an abnormal noise, you are the hard disk is about to break, hurry up and back up important data and replace the hard drive!
Replace the memory module and wipe the gold finger.
Check whether the output voltage of the power supply is normal.
Usually there are just a few items, if there is a problem, just change it!
-
Blue screen. Is it a problem with your hardware configuration? This problem is generally rare.
The one who is there is the memory. Take off the memory module and wipe it.,If it doesn't work, change the memory module.,Mine is like that, the blue screen frequency is very high.,I'll just change one.,And it's good to clean up the case (the cup fan is the most important.,Because the data processing can't be done, it will also cause a blue screen.),The case will also have a blue screen if it's dusty.。
-
Same as I did a few days ago, it's not the system reason, it's your memory module is dirty, unplug the memory module after washing your hands (anti-static), wipe the gold finger (yellow part) with a clean thing, just press it, don't: never blow it with a hair dryer.
-
You remove the hard drive, put it on your friend's computer, boot it up with his system, back up the important data, and then repair the system.
It's safe and a bit of a hassle.
-
Remove the memory module, wipe it, and try to plug it in again.
-
If you often have a blue screen of death, it's a hardware problem
-
Unplug the memory and wipe it or borrow one from a friend to try it out.
-
I think it's the hard drive that has bad sectors.
-
1.Unplug the memory and wipe it well. Unplug one of the two memories and try it.
2.System file corruption, overwriting the installation or reinstallation of the system.
-
1.It is possible that there are bad sectors on the hard disk of the computer.
2.If there is a problem with the memory module, unplug it and use it"New money"Wipe it down"Goldfinger"
-
The system is broken, really hehe, you lost a lot, last time my computer was like this, I changed it!
-
It feels like it's a problem with your graphics card, see if the graphics card is loose, and it's more likely that the contact is not good.
-
Whether you have recently reinstalled your computer Whether you have installed new software.
-
An accidental blue screen is irrelevant, it's fine.
Often the blue screen may be tricked in the system, or the compatibility of the hardware is not good.
-
Is your system hard to 98? If it's time to change! If it is not the system version, it should be checked to see if it is a mechanical fault such as a fan.
-
It should be a memory issue. Remove the memory and wipe the gold finger with an eraser. But it can't be ruled out that it's a software problem, because I've encountered it, and the computer with a certain software turns on a blue screen soon after, so I have to use ghost to restore it.
So I recommend you. Do the following to determine the hardware problem. 1.
Rub the memory gold finger. If the computer is normal, then it is a memory problem. 2.
If you still have a blue screen, back up your important files and then reinstall the system. It should return to normal. 3.
If it doesn't work, then you may have to change the hardware if it's a hardware problem.
-
0x00000019 This generally refers to the fact that the disk drive cannot find the specified sector or track on the disk.
1. Open the chassis, unplug the memory, use the eraser gold finger, and plug it in a different slot; Take one of the two memories and try it. Increase memory.
2. Check for new hardware, new drivers or services, if the blue screen is caused by installing new hardware, new drivers or enabling and closing services, you can uninstall or disable (enable) in safe mode.
3. Check the newly installed software, sometimes some firewall software will cause this failure.
4. Patch the system or reinstall the system.
5. Turn off memory options in the BIOS, such as cache and mapping.
6. Check whether the disk is damaged, scan and repair the hard disk.
7. Check for viruses.
-
There are many kinds of blue screen situations, and generally people who have watched **even if they know** can't do it, because the blue screen** is too article-like, that is to say, it is not easy to understand, and there is no specific explanation. Generally, when we encounter a blue screen, we try to install the system first, because I have also had the problem of the blue screen is the system when watching TV before. If you still have this situation after installing the system, it is recommended that you exclude Memory-Graphics Card-Motherboard in order.
If you can't change anything, it's definitely the motherboard.
Good luck!
-
Don't be surprised if you have a blue screen once in a while, just restart, if this problem often occurs, it may be a problem with the memory, or it may be a problem with the hard disk.
-
If you have a problem with memory or hard disk, try to reinsert the memory, and chkdsk the hard disk to see if there are any bad sectors.
-
Disk error (0x00000019 bad pool header is information that cannot be read in a specific area of the disk, and this "specific area" seems to be similar to a "local area" where it rains every day, and it is difficult to pinpoint it).
-
System problems: Ah, you can reinstall the system, if it's not too troublesome, hehe, actually, blue screen.
It's not a big deal either.
-
It's normal for computers to have occasional blue screens!
-
It's a virus, I've seen it before, you'd better get a better antivirus, like Kingsoft Antivirus, and get a full antivirus. Jinshan Poison Bully is quite good, you don't need money for the first month, you can kill the poison and delete it.
-
The blue screen situation is complicated.
With your narrative no one knows what the problem is.
Suggestion: Carefully get the memory!
-
I'm dizzy, you said it yourself, it's the graphics card is incompatible, then it must be a blue screen, just change to a graphics card that is compatible with your motherboard model.
-
It's time for your machine to be replaced, you go to the system, and if you reformat, it's still not good, so you go to change the graphics card, something went wrong, and your computer is really good, and you have to have fun, and it's okay to play for 5 years.
It is recommended to reinstall the system.
When the system is newly installed. >>>More
Blue Screen" software causes and solutions: 1. Loading too many programs at startup Don't load too many applications at startup (especially if your memory is less than 64MB), so as not to exhaust system resources. Under normal circumstances, the system resources should not be less than 90% after win9x starts. >>>More
The blue screen of death, also known as the blue screen of death (BSOD), refers to the image of the screen displayed by the Microsoft Windows operating system when it is unable to recover from a system error. >>>More
1。Try to boot up, after the computer brand is out, press F8, Safe Mode, Cursor Select: Last Correct Configuration, Enter, Enter, Press Down! [Critical step]. >>>More
1. If it is caused by hardware problems, or overclocking CPU and other hardware to discharge the BIOS battery (restore the BIOS factory default), it is recommended to plug and unplug the graphics card, memory and other hardware, clean up the hygiene in the computer, and polish the gold finger of the graphics card and memory (to test whether the temperature of the hardware is too high). >>>More