What are the benefits of running flat seams in pants?

How to hem pants. Tips.

1.Find the length that suits you. Make sure how much you want to make your pants shorter so you know how long to sew the frills.

Put your pants on and use a tape measure to measure how much fabric you need to cut. In general, the hem should be about a centimeter off the ground, but it all depends on your personal preference.

2.Measure the size. Take off your pants and spread them out on a smooth surface. Use a tape measure to measure the distance from the existing frills to the bottom of the hem (usually about centimeters, but depending on the trouser style).

3.Fasten the pants with a pin. Pin a few pins to the hem you want to modify, and you'll sew the hem in that area.

Then, pin the second row of pins above the new seam edge. The distance between the 2 rows of pins and the leg and the original frills is the same (usually centimeters). During the modification process, the original frills will be retained, so the second row of pins must slightly reduce the length added to the original frills.

4.Adjust the pins. Remove the first row of pins near the bottom of the hem. These pins were originally used to mark the cuffs of the pants that fit to fold. Now, you can save them for the next step to secure the hem.

5.Fold up the trouser cuffs. Turn the bottom of the leg inside out and fold it up to the second row of pins.

Flatten the fabric, remove creases and creases, and make sure the cuffs are folded in the same place on both sides. Use the freshly removed pin to secure the folded fabric in place below the original frills.

6.Sew new frills. Use a straight needle to thread the hem of the trousers and seam the folded area.

Sew new frills underneath the original frills at the hem (the fabric must be folded up and close above the fold). The stitches along the hem of the trousers must be straight and neat, and after sewing, the needle is reversed or knotted to cut off the excess thread.

7.Fold the sewn area back. The bottom of the hem is sewn to form a loop. Fold the stitched fabric back into the hem and turn the front of the hem out. You've successfully seamed the hem!

8.Iron the frills. You can cut off the excess fabric at the frills, but the easier way is to iron them out. Adjust the iron to the fabric of the pants, then iron the frills to flatten the stitched fabric. You can use a lot of steam, which makes it easier to flatten the frills.

The seam of the pants is off the line, and I don't think it's good, right?

If the seam of your pants is misaligned, it doesn't do any good, we make others look like you're wearing your pants when you're walking.

The seam of the pants is flattened, there is no benefit at all, it is not good-looking, and it is awkward to wear.

I don't think it's any good, the general trouser line is straight, and if it's crooked, it's broken.

There is no benefit to the misseam of the pants, and it is very difficult to wear and need to be re-sewn.

1. The front and back pieces are not aligned.

Compared with the front film, the rear film is caused by unilateral placement. This is 90 per cent. This kind of pants can be disassembled and re-sewn, or the iron can be heated and stretched to relieve simple skew.

2. There is a problem with planting and cutting.

In such a situation, it is necessary to disassemble the pants, find the center line, and re-cut the sewing. Changing wide pants to thin can solve the problem, if the pants are too skinny, it can't be changed.

There is no benefit to the misalignment of the pants, and it is not very comfortable to wear.

Because that's how these pants look. So, the hem of the pants is all pleated.

This is mostly related to the material of the pants, but it doesn't have any effect, just make a recovery of the shape.

If there is a missing line or an open line, it can be returned.

1. To mend the seam of the trousers, first find a sewing thread similar to the color of the pants, the needle is not too thick, try to choose a thinner needle. String the thin wire in the pinhole and tie a fine knot at the end of the wire.

2. Then, break the seam of the pants to be sewn a little, see the traces of the original sewing of the pants, insert the prepared needle and thread from the reverse side, and start sewing along the original sewing traces.

3. Preferably, each needle should be pierced a little bit inside the original trace, and the needles on the left and right sides are the same way, as shown in the figure below.

4. When sewing a stitch, don't pull the thread too tightly, sew it loosely and evenly, and the stitches should not be too large (about millimeters apart between each stitch).

5. When sewing the thread, it is relatively smooth to pull forward and upward, otherwise the suture is not easy to flatten, and even easy to make the seam hole bigger.

6. After the sewing (about half an inch long) is completed, the stitches can be gently tightened forward and upward, and the sewing will be smooth and perfect.

The sewing techniques for the waistband of the trousers are as follows:

1. Sew the elastic bands first!

2. Measure the waist of the pants to be sewn and fold it down, then draw a line at the place and sew it around.

3. Put the elastic bands well, press the cloth and sew the elastic bands.

4. Where it is not long enough, stretch the elastic band and sew it well. The seam is generally selected at the interface.

My method: Pull one side of the elastic band and the top of the waist directly (divide the segments), and then wrap the elastic band and then car. I have made more than a dozen of this method, especially the thin material, the finished product is good-looking; Thick cloth (thick velvet), first turn the waist well, and then wear it in; On the other waist, first turn the elastic band and the elastic mouth into a circle, the elastic mouth is outside, the elastic band is inside, and the waist of the pants is on the car together.

The third method is best done, and I like the first method, because it is waist-connected, and the waist is the material of the pants.

Denim fabric in general.

bai is pure cotton, and after the sewing du is completed, you need to take zhi to the sand washing factory for sand washing, and the water shrinkage of dao is 5%.

It's hard to get inside. When sewing, a thread volume is evenly forced, and after shrinkage, uneven shrinkage occurs in the place where the force is large and the place where the force is small.

The tighter and looser parts of the tension naturally form bends.

The last time I sold the Baleno was crooked.

I've also encountered such a problem, and it was very good when I saw it, but after I bought it, I looked closely and found that it was crooked.

The quality is too inferior, try it in a specialty store.

The design is not reasonable, unless it is tailor-made, we are buying clothes that suit us It is impossible to be completely without any shortcomings.

Hello! If the pants need to be repaired, if you are not a professional, in order to ensure that the repaired clothes are comfortable to wear and avoid damage to the clothes, it is recommended to consult or sew them at a professional clothing repair shop.

If there are local stains on the clothes in daily life, such as oil stains, fruit stains, etc., the following methods can be used to clean them

1. When the clothes are dry, apply the original solution of the special laundry detergent for hand washing to the stains, completely cover the stains, let it stand for 5 minutes (it can be gently scrubbed), and add laundry detergent for regular washing;

2. If the stain cannot be removed after the above methods, then.

1) Pure white cotton, linen, polyester clothing: Add 1 bottle cap (40g) of white clothes (600g specification) to each half basin of water (about 2 liters), stir well, soak in the clothes for 30min, and rinse clean.

If the stains are not removed after 2 hours, take out the clothes, add white clothes to the basin (add 1 bottle cap per half basin of water), stir well, put in the clothes and continue soaking, and the cumulative soaking time does not exceed 6 hours.

2) White clothes of colored or other materials: put the clothes into the basin, the stain part is attached to the bottom of the basin, measure 1 4 caps (10 grams) of colored clothes and 1 4 caps (10 grams) of the collar with the color stain net (600g specification) of colored clothes, pour them on the stains, cover the stains with other non-stained parts of the clothes, prevent air drying, let stand for 2 hours, and rinse clean. If the stain remains unremoved after 2 hours, it can be left on for an extended period of time overnight.

Precautions: 1. White clothes are suitable for white cotton, linen, polyester, polyester cotton, cotton and linen fabrics, do not use colored clothes (including white background stripes, white background checkered, white background printing), do not use silk wool spandex nylon and other non-chlorine bleaching clothes, do not directly use the original solution.

2. Color stains are not suitable for fading clothes and dry cleaning, avoid touching metal buttons, zippers, metal ornaments, etc. on the clothes when using, and avoid direct sunlight.