How to install a tractor rotary tiller for automatic leveling

The connection method of the suspended rotary tiller is basically the same as that of the suspended plow, but it also needs to be connected with the power take-off shaft on the tractor with a universal joint, and the following two points must be paid attention to when installing the universal joint:

1) The length of the square shaft should be suitable for the tractor, so as to ensure that when the tractor is working and lifting in the farmland, the square shaft and the square sleeve are not dead and have enough matching length.

2) The two clamp forks in the middle of the universal joint should be on the same plane, otherwise the speed of the cutter shaft will be uneven, the vibration will increase, and the sound will be generated, so that the parts will be damaged in advance.

Adjustment method: 1) left and right horizontal adjustment: park the tractor with rotary tiller on the flat ground, and lower the rotary tiller, so that the blade is 5 cm away from the ground, observe whether the left and right knife tips are consistent from the ground, and ensure that the knife shaft is consistent and the ploughing depth is uniform in the farmland operation, 2) the front and rear horizontal adjustment:

When the rotary tiller is lowered to the required depth, observe whether the universal joint and the rotary tiller knife shaft are close to the horizontal position, if the angle of the universal joint is too large, the upper pull rod can be adjusted to make the rotary tiller in a horizontal position.

3) Lifting height adjustment: the angle of the universal joint should not be greater than 10 ° during operation, and it is not allowed to be greater than 30 ° when the head turns.

Judging from the ** and eye color and facial features, it can be determined that it is a yellow race, Asian. But whether the Chinese are not sure, because Koreans, Japanese, etc. are possible.

According to the selected tractor model, horsepower to purchase the machine supporting the rotary tiller.

Generally speaking, the single-cylinder 20---24 horsepower tractor, supporting rotary tiller model 125; Single-cylinder 24--35 horsepower tractor, supporting rotary tiller model 130;

Twin cylinder 25 horsepower tractor, supporting rotary tiller model 140;

30--35 horsepower tractor, supporting rotary tiller model 150--160;

40 horsepower tractor, supporting rotary tiller model 160-170;

50--55 horsepower tractor, supporting rotary tiller model 180--200;

60--72 horsepower tractor, supporting rotary tiller model 200--220;

75--95 horsepower tractor, supporting rotary tiller model 220---230;

Tractors with more than 100 horsepower, supporting rotary tiller model 230-250.

Summary. Tractor rotary tiller plough depth adjustment method: use the floating rotary tiller to put down the tractor when you feel that the tractor is struggling, Bao Te neutral, shallow forward to shoot the control lever, deep to the back of the pat, do not stop too long when shooting, otherwise put too much or the knife shaft off the ground.

When the tractor is equipped with a rotary cultivator, it is mainly carried out with a rear suspension device.

How to adjust the depth of the tractor rotary tiller?

Tractor rotary tiller plough depth adjustment method: use the floating rotary tiller to put down the tractor when you feel that the tractor is struggling, Bao Te neutral, shallow forward to shoot the control lever, deep to the back of the pat, do not stop too long when shooting, otherwise put too much or the knife shaft off the ground. When the tractor is equipped with a rotary cultivator, it is mainly carried out with a rear suspension device.

Hope it helps.

Hello dear, how to debug the rotary tiller to pull the light and deep method is as follows: 1. Adjust the left and right levels. The towing with the Jinling rotary tiller is initially parked on the flat ground, the rotary tiller is lowered, the blade is 5 cm away from the ground, and the height of the left and right knife tips from the ground is observed to ensure that the level of the knife shaft is consistent in the operation, and the depth of the cultivator is uniform.

2. Adjust the front and rear levels. When lowering the rotary tiller to the required depth, observe whether the angle between the universal joint and the axis of the rotary tiller is close to the horizontal position. If the angle of the universal joint is too large, the upper tie rod can be adjusted to make the rotary tiller in a horizontal position.

3. Lifting height adjustment. In rotary tillage operation, the angle of universal joints is not allowed to be greater than 10 degrees, and it is not allowed to be greater than 30 degrees when the head of the ground is turned. Therefore, for the lifting of the rotary tiller, for the use of the available screw of the position adjustment, the appropriate position of the handle is tightened and the limit is screwed; If you need to raise the rotary tiller again, the power of the universal joint should be removed.

The depth and weight of the rotary tiller can be adjusted by the following methods: 1Adjust the depth of the cutterhead:

The cutterhead depth of the rotary tiller can be controlled by adjusting the height of the cutterhead. Generally speaking, the deeper the cutterhead, the heavier the rotary tiller will be when pulled up, and vice versa. Therefore, you can try to adjust the height of the cutterhead until you reach the desired depth and weight.

2.Adjust the rotation speed: The rotation speed of the rotary tiller will also affect the lightness and weight of the pull.

If the rotation speed is too fast, the rotary tiller will become heavier, while if the rotation speed is too slow, it will become lighter. You can adjust the speed of rotation to achieve a weight level that suits you. 3.

Adjust the wheel height: The wheel height of the rotary tiller will also affect the weight of the pull. If the wheels are too high off the ground, the rotary tiller will be lighter, while if the wheels are too low off the ground, it will be heavier.

Therefore, you can try adjusting the height of the wheels until you reach the level where you want to travel without missing a stool.

It is recommended to bring a 220 rotary tiller! It's too big to move! The general speed is 720-850! Now the new Dongfang red is 720-1000!

The walk-behind tractor is a small tractor with a power of less than 11kw (15 horsepower), which is mainly suitable for farmland operations and short-distance transportation operations in small fields, and is more commonly used in rural areas in the south.

Wheeled tractors are divided into two types: belt drive and power take-off shaft drive, belt drive is generally a small four-wheel tractor, with a power of 20 horsepower).

The power take-off shaft is driven by large and medium-sized tractors, and the power is above the horsepower, and the power of the tractor is getting bigger and bigger with the needs of production; Wheeled tractors are mainly used in rural areas in northern China for farmland operations or transportation operations, among which large wheeled tractors are suitable for use in large-scale farmland production, which can greatly improve production efficiency.

Because crawler tractors can be equipped with bulldozer blades, they are generally used in farmland capital construction and water conservancy projects.

Summary. Hello, dear; Tractor butt rotary tiller installation**Yes; 1. Built-in method: the left curved blade is installed on the right side of the knife shaft, and the right curved blade is installed on the left side.

This installation method makes the middle of the ground ridge after tillage, which is suitable for land preparation before furrowing. 2. Exterior method: In addition to the outermost blade is internal, the left curved blade is installed on the left side of the knife shaft, and the right curved blade is installed on the right side of the shaft.

In this way of installation, after the tractor is operated, a shallow ditch will appear in the middle of the field. 3. Staggered installation method: the left and right blades are staggered on the cutter shaft.

In this way, after the tractor operation, the surface of the cultivated land is flat, which is suitable for harrowing the land after plowing or plowing the land before sowing, which is a more commonly used installation method.

Hello, dear; Tractor butt rotary tiller installation**Yes; 1. Built-in method: the left curved blade is installed on the right side of the knife shaft, and the right curved blade is installed on the left side. This installation method makes the middle of the ground ridge after tillage, which is suitable for land preparation before furrowing.

2. Exterior Magic: In addition to the outermost blade is internal, the left curved blade is installed on the left side of the knife shaft, and the right curved blade is installed on the right side of the shaft. In this way of installation, after the tractor is operated, a shallow ditch will appear in the middle of the field.

3. Staggered installation method: the left and right blades are staggered on the cutter shaft. In this way, the ruler, after the tractor operation, the surface of the cultivated land is flat, suitable for harrowing the land after ploughing or ploughing before sowing, and it is a more commonly used installation method.

There are three precautions for the installation of the blade of the rotary tiller: The installation of the chisel knife is not special to be cautious, for the straight hook chisel knife, the ability to enter the soil is strong, the performance of throwing over the soil is poor, and it is easy to hinder the grass, which is suitable for the soil with few weeds and compacted. Its installation is generally evenly arranged on the flute according to the spiral line, and fixed on the tool holder with screws.

For the left and right scimitars with curved blade heads and long cutting edges in the outer arc, the cutting ability is strong, and it is suitable for water and dryland farming, and has a wide range of applications. If the blade is not installed correctly, it will not only affect the quality of the work, but also affect the service life of the tool.

Hello, dear; The link to the Dan book that provides you with Qisan is [[Yuefeng Machinery] Tractor Rotary Cultivator Quiet Chi's Assembly Tutorial.