How can I turn on the faucet and get hot water? What s the best way to do it?

We can choose a gas water heater with zero cold water and then set it to an automatic circulation mode, so that in this case, there will be hot water as soon as the faucet is turned on.

You can use the kitchen treasure skillfully. I can install a kitchen treasure in the kitchen drain area, and then I can get hot water directly.

We can install small kitchen treasures, we can also buy some hot water taps, and we can also buy some gas water heaters with zero cold water.

<> normal water, the hot water from the faucet is supplied by a water heater**, as opposed to the electric water heater used by most households in the past.

Or solar water heaters.

As a result, the water that remains in the pipe becomes colder, so that cold water comes out for a long time after turning on the faucet. If you want to solve this problem, you can use the following methods to achieve the goal of turning on the faucet to produce hot water.

One is the kitchen treasure. This is the most straightforward and relatively low-cost way, whether your home is preparing to be renovated or has already been renovated, you can install a kitchen treasure in the kitchen drain, and the kitchen treasure can directly supply hot water after opening the faucet. Kitchen treasure has water storage tank type and instant heating type, the water storage tank type ** is relatively cheap, the power consumption is relatively low, the disadvantage is that when the amount of hot water is large, the hot water may be used up in a short time.

The second is the instantaneous faucet. This is the most direct way to open the faucet and use hot water directly, that is, the hot faucet is now more close to the people, you can buy it on the e-commerce platform, and many products can also be installed on the door. However, the downside is that the power consumption of instantaneous faucets will be relatively high, and the cost of use will climb for households that frequently use hot water in the kitchen.

The third is the circulating pump. This method is relatively complex, and the principle is to recycle the cooled hot water from the hot water pipe between the water heater and the faucet back into the water heater for heating. The cost of the circulating pump device will be higher, and relatively speaking, it is more suitable for the family that is preparing, if it has been renovated, and then want to install the circulating pump, it will still have a certain impact on the overall layout of the house.

The fourth is zero cold water heater. This method is similar to the principle of the circulating pump, which is to circulate the cooled hot water in the hot water pipe back to the water heater for heating, but it has the advantage of circulating the device, heating device, and return pipe.

and so on, the overall decoration effect will be more beautiful. In addition, after all, it is an integrated whole, and the stability will be higher.

The above are some of the ways to realize the hot water when you turn on the faucet, I hope it will help you!

If you want to turn on the faucet and the water comes out, you need to configure the hot and cold handover, that is to say, you can ask a decorator to configure an installer for the hot and cold water pipes at home. Or install the small kitchen treasure at the faucet.

You can install a water heater at home so that hot water comes out when you turn on the faucet again. The better way to do this is. You can connect a gas water heater, you can install an electric water heater, you should also pay attention to the connection of water pipes, and you should also pay attention to the use of water separators, so that you can achieve such an effect.

Adjust the temperature control system to the best, and turn off the hot water when not in use, which can not only produce hot water when in use, but also save electricity; You can install a small kitchen treasure at the faucet, you can also replace the faucet with a ready-to-heat faucet, or you can not turn off the electric water heater when the hot water is not in use.

The reasons could be:

1. The porcelain core in the cold and hot water faucet is broken, and the faucet can only be connected to the side of the outlet pipe of the electric water heater, not the side of the cold water;

2. The cold water pipe is blocked or closed by the faucet in front. Try turning off the power to the electric water heater to see if there is still hot water.

A faucet is a valve that controls the flow of water. The faucet of a British basin or bathtub is usually the two ends of the hot and cold separation. In the United States, as well as in other countries, it is mostly hybrid faucets.

The latter is produced only after the hot and cold water is mixed, so the water can be controlled at different temperatures.

The main raw material of the faucet is copper and zinc alloy. If you install a separate tap, the tap water doesn't have to be hot or cold. Usually hot faucets have a red light or symbol, while cold faucets usually have a blue or green light or symbol.

In English-speaking countries, faucets are also often marked with an "h" or "c" for hot or cold. Most residential, commercial and industrial houses have a faucet in front of the door, and they are equipped with a switch with a square hole to prevent passers-by from using water indiscriminately.

This is mainly because the hot water stored in the hot water pipe is cold because it is not used for a long time, when we turn on the hot water, the hot water faucet first releases the hot water that is cooled out in the hot water pipe, and then slowly flows out of the hot water in the water heater. This part of the water needs to be drained before each use of water – not only that, but there is still hot water in the pipes after use, and this part of the hot water will slowly cool. Secondly, to achieve energy saving and power saving, there are several kinds of hot water equipment, such as high-power gas, high-power electric water heaters, air energy water heaters, etc., which is the trend of hot water development.

To be honest, if the gas water heater installed at home is changed to zero cold water, it is better to change a little, it is a wall-hung boiler, it is more troublesome, there are too many things to change, see if you are reluctant, I will draw you a construction drawing first.

<> heating and hot water dual-purpose wall-hung boiler has the function of powerful home heating and providing high-flow constant temperature sanitary hot water, which is equivalent to concentrating heating equipment and hot water equipment in one product, with high efficiency, fast heating, and small floor space, which is highly respected by the majority of users. This problem has to be a professional master you, now the technology is very developed, if it is an old water heater to install additional equipment, if you are just decorated it is recommended to the worker master to tell him to do the circulating water on the best circulation to the water outlet, so that the water is saved, a section of electric heating pipe heating, a thermoelectric coupling controller, the cool water section is first heated with electricity, when the perception of the hot water in the water heater is about to arrive, the power is cut off, and the water heater is hot water.

First, you need to purchase a water return, and then connect the angle valve under the far end of the water point with a check valve. At this time, part of the cold water pipe acts as a circulating water pipe, which can also shorten the cold water release time. Don't fool people when it comes to circulating pumps.

I have installed a circulating pump in the air at home, and the electricity is more than 40 degrees per day, and I have been using it for more than two years, and I have a power supply bureau to overhaul the circuit at the door, and I casually asked why my household electricity is so high, and they told me to turn off the circulating pump, <>

If I want to turn on the faucet and there is hot water, we can install a superheater, which is very developed nowadays, and the hot water will come out immediately.

You should turn on the water heater in advance and let the water heater run for a longer period of time, so that the water coming out of the faucet will become hot.

The main thing is that you have to have a water heater, whether it's solar, or the kind that's plugged in, solar, if it's cloudy, there may be no hot water.

You should find a maintenance master to see if the interface is not connected to cold water, and the cold water port should be opened to access cold water, so that the switch can be placed in the middle to have warm water come out.

Hello dear, the traditional electric hot water faucet is prone to this situation, and you need to adjust the water temperature by yourself. It is recommended to use a thermostatic electric hot water faucet. 1. Turn up the water temperature, which is now mostly electronic, with buttons with arrow directions.

2. The distance is too far, and you need to put a lot of water to produce hot water. 3. Try to turn off the cold water in the water inlet pipe. 4. There is a problem with the quality of the electric water heater itself.

Nowadays, faucets have been commonly used, however, many people are a little puzzled about the use of faucets, so how to make the faucet hot water, what are the good ways? Let me introduce it to you.

It takes a long time to open the faucet to put cold water to produce hot water, on the one hand, it is a waste of water resources, and on the other hand, it is very inconvenient to use, especially in winter, after careful research, there are the following three schemes that can be used.

1. Install a water-storage electric kitchen treasure under the wash basin and vegetable washing basin, wash your hands and wash vegetables with kitchen treasure, take a bath and still use the current gas water heater, the problem of the scheme is that although the number of baths is not as frequent as washing hands, you still need to put cold water for a long time when taking a bath, and at the same time, only a power socket is installed under the washing basin during decoration, so when installing the kitchen treasure under the wash basin, you need to walk the power supply line on the wall, which is very unsightly; To choose this solution, you need to set up an outlet under the vegetable sink when the water and electricity are changed in advance.

2. Install a storage electric water heater in the bathroom, but because many of the walls of the bathroom are not load-bearing walls, it is generally impossible to install a wall-mounted electric water heater, and can only install a seated water heater that can be placed under the washbasin When using hot water in the kitchen, you must continue to put cold water (whether you use the original gas water heater or use the electric water heater with the main wide lead sleeper); 3. Install a hot water circulator on the position of balcony gas water heater, the cold water in the hot water pipeline can be pressed into the cold water pipe through the circulation system, so that the hot water can be immediately discharged as soon as the faucet is opened, and the circle can be kept back (the gas fee), the loop can be controlled by temperature, and the loop can be looped by timing (such as setting the loop after getting up in the morning or the loop before going to bed at night, etc.), so as to effectively solve the defects of the first two kinds of hot water circulation system.

Electrically heated faucets I don't think are very practical; It is possible to produce hot water immediately, but the power consumption will be very high, and it is also very expensive.

The electric heating faucet actually has a certain practicality, it can not immediately produce hot water, it needs a certain heating time to be able to produce hot water, this kind of electric heating faucet is generally more convenient, plug it in if you use it in winter, and unplug it if you don't use it.

The electric heating faucet is very convenient, especially when it is used in winter, you can immediately produce hot water, and it is also very convenient when washing dishes.

1. It may be due to temperature, for example, in summer, the temperature is relatively high, and the cold water pipe is exposed to the sun, which makes the internal water heat up, so after turning on the hot water faucet, what flows out is hot water. But when the hot water is drained, the cold water will be able to flow out later, so it's only a matter of time. 2. If it is not a problem of temperature, it may also be that the valve core is damaged, resulting in the problem of water seepage in the faucet, and it is hot water when it is opened.

The probability of collusion in the waterway is still relatively large, in this case, it is necessary to replace the new valve core.

If you want to turn on the faucet to produce hot water, you can generally screw the faucet to the far left, so that it is the direction of hot water, and the water is hot water, mainly depending on the direction of hot water set by each family, to decide which side of the hot water comes out.

Turn on the faucet to produce hot water, it is not very difficult to make such an effect, you only need to install the return pipe when you decorate your home, and then when you buy a water heater, you can buy a water heater with zero cold water. The principle is to heat up in advance, so hot water can be produced when the faucet is turned on.

You can set up a small kitchen treasure in the basin area, so that the hot water can be quickly distributed.