In winter, the amount of hot water is large, how can I turn on the faucet to produce hot water?

In winter, the amount of hot water is large, and if we want to turn on the faucet as soon as it is hot water, we must turn on the inching mode and all-day cycle mode of the gas water heater, but first you have to ensure that your water heater is a zero cold water heater, so that the hot water will come out as soon as the faucet is turned on. However, this model of water heater is very draining.

My family just solved this problem a few days ago, looking for a decoration master to install a kitchen treasure, and then when the water is directly turned into hot water, overall the effect is not good, I recommend everyone.

This should be a bit difficult, after all, it is the winter season, which will cause the water accumulated in the pipes to become cold, and this part of the water cannot be heated by the water heater, so it is generally cold water for a while before the hot water is released.

The more the water heater at home comes out of the faucet in winter, the slower the hot water comes out, and every time you need to wait for hot water, wait until you receive most of the bucket of cold water before waiting for hot water, which not only wastes water but also affects the mood of bathing. In winter, the water in the tap takes a long time to get hot, why is that?

The tap is far from the water heater

This is more common because the tap is farther away from the water heater, and the farther the spacing, the longer the pipe. Generally speaking, everyone's hot water will flow from the water heater through the pipe to the point of use, and the whole process will be in harmony with the natural environment.

I develop a heat exchanger with water wall thickness (the temperature of water wall thickness is the same as the temperature of the condition), calories of hot water.

It will be consumed until there is no temperature difference between the temperature and the wall thickness. As a result, the specific temperature of the drain will be lower than the temperature set by the water heater until the temperature is stabilized.

On the other hand, the longer the length of the pipe, the more cold water is stored in the pipe, and the rate at which the hot water goes out will be slower, and there will be a waiting time, which can also be expressed why the waiting time will be longer in winter.

Cold water residue between the drain and the pipe

In addition to the fact that the tap is far away from the water heater, there is also a section of tap water pipe connection between the tap and the pipe, and cold water residue will also appear in this section. Everyone usually uses the shower to take a bath, and after washing, there will be some water left in the tap pipe that connects the shower and the water channel.

This part of the water is not easy to flow back into the pipeline, but remains in the pipe, as soon as we turn on the faucet or showerhead, the first thing that goes out is cold water.

The hot water in the pipeline does not need to be turned cold when it is idle

This is also the direct reason why everyone "waits for hot water", which is also called the "cold water section". Generally, the water in the home is connected to each other according to the pipes, and there is a section of tap water pipe between the water heater and each water point. When we use hot water, the pipes are full of hot water, and once the hot water is deactivated, this section of hot water is stored in the pipes.

The general pipe does not have a unique thermal insulation effect, and the temperature around the pipe is relatively low in winter, when the water point does not use water for a long time, the hot water in the water pipe will become cold water, which is why the hot water waiting time will be longer in the winter morning.

Nowadays, the time to wait for hot water is slightly longer than in summer, and there is no need to panic, after all, the weather has been so cold recently, and there is a reason, which is all the normal situation of the water heater output. The water heater has not been able to produce hot water, it is likely that the water heater is abnormal, such a thing should be immediately repaired by professionals.

Because the temperature in winter is relatively low, the water needs to be sucked out of the ground and then flow into the faucet, so the temperature is relatively low, which is related to the heating equipment, and it may be that the water connection pipeline is relatively cold.

This is a very normal situation because there is a certain distance between the water heater and the faucet, and the flow rate of the water also takes a certain amount of time.

Because there is a certain distance between the faucet and the connected pipe, and the speed of the water flow also takes a certain amount of time.

Electrically heated faucets I don't think are very practical; It is possible to produce hot water immediately, but the power consumption will be very high, and it is also very expensive.

The electric heating faucet actually has a certain practicality, it can not immediately produce hot water, it needs a certain heating time to be able to produce hot water, this kind of electric heating faucet is generally more convenient, plug it in if you use it in winter, and unplug it if you don't use it.

The electric heating faucet is very convenient, especially when it is used in winter, you can immediately produce hot water, and it is also very convenient when washing dishes.

Nowadays, faucets have been commonly used, however, many people are a little puzzled about the use of faucets, so how to make the faucet hot water, what are the good ways? Let me introduce it to you.

It takes a long time to open the faucet to put cold water to produce hot water, on the one hand, it is a waste of water resources, and on the other hand, it is very inconvenient to use, especially in winter, after careful research, there are the following three schemes that can be used.

1. Install a water-storage electric kitchen treasure under the wash basin and vegetable washing basin, wash your hands and wash vegetables with kitchen treasure, take a bath and still use the current gas water heater, the problem of the scheme is that although the number of baths is not as frequent as washing hands, you still need to put cold water for a long time when taking a bath, and at the same time, only a power socket is installed under the washing basin during decoration, so when installing the kitchen treasure under the wash basin, you need to walk the power supply line on the wall, which is very unsightly; To choose this solution, you need to set up an outlet under the vegetable sink when the water and electricity are changed in advance.

2. Install a storage electric water heater in the bathroom, but because many of the walls of the bathroom are not load-bearing walls, it is generally impossible to install a wall-mounted electric water heater, and can only install a seated water heater that can be placed under the washbasin When using hot water in the kitchen, you must continue to put cold water (whether you use the original gas water heater or use the electric water heater with the main wide lead sleeper); 3. Install a hot water circulator on the position of balcony gas water heater, the cold water in the hot water pipeline can be pressed into the cold water pipe through the circulation system, so that the hot water can be immediately discharged as soon as the faucet is opened, and the circle can be kept back (the gas fee), the loop can be controlled by temperature, and the loop can be looped by timing (such as setting the loop after getting up in the morning or the loop before going to bed at night, etc.), so as to effectively solve the defects of the first two kinds of hot water circulation system.

Summary. The reason why the electric water heater produces large hot water and small cold water output: the temperature setting is too high, and the water temperature is high and then mixed with cold water at the mixing valve, and the overall water temperature naturally rises, and the hot water is large and the cold water is small; The mixing valve is scaled or foreign matter causes the uneven ratio of hot water and cold water, resulting in large hot water and small cold water; The hot water pipeline is blocked, so that the hot water output flow is small, and the overall water temperature drops after mixing, which cannot meet the requirements of use.

The corresponding solution to the above problems: set the temperature lower to reduce the temperature of the hot water; Clean the inside of the mixing valve, remove the scale and foreign matter inside, and replace it in time if there is damage; Clean the hot water pipes and showers regularly to ensure that the water inside them is unimpeded. If the shower is damaged, or if the software is severely kinked, it can be replaced with a new product.

The hot water outlet closest to the water heater, when the faucet is turned on, it is cold water, and when it is turned on, it is hot water.

The hot water outlet of the electric water heater is large and dry, and the cold water is small: the temperature is set too high, and the water temperature is mixed with cold water at the mixing valve after the output is high, and the overall water temperature naturally rises, and the hot water is large and the cold water is small; The mixing valve scale or foreign matter causes the uneven ratio of hot water and cold water, resulting in the situation of large hot water and small cold water; The hot water pipeline is blocked, so that the hot water output flow is small, and the overall water temperature drops after mixing, which cannot meet the requirements of use. Solutions to the above problems:

Set the temperature lower to lower the hot water temperature; Clean the inside of the mixing valve, remove the scale and foreign matter inside, and replace it in time if there is damage; Clean the hot water pipes and showers regularly to ensure that the water inside them is smooth and unimpeded. If the shower is damaged, or if the software is severely kinked, it can be replaced with a new product.

It may also be the reason for the scale generation, the temperature of the heat exchange surface of the water heater is very high, and the scale will be generated when the water flows over, and after a long time, there will be a lot of scale attached to the surface of the heat exchanger, which will accumulate over time, resulting in the blockage of the hot water pipeline, which will cause the water output to become smaller (the phenomenon of small water pressure), and the hot water output time will become longer. Jiansun which first discusses cleaning and descaling, buy a set of fast water heater without removing the scaler online, use it to inject descaling agent into the water heater to clean the inside of the water heater can be solved, the operation is simple and convenient, use it to clean it regularly, when you can avoid this problem again. A lot of people have used it, and it really works.