How to deal with sewer oil blockage in winter

You can pour hot hot water into the drain to let the oil melt and go downstream.

1. Rice water and baking soda.

In fact, rice washing water has a strong decontamination ability, and when used with baking soda, the cleaning effect will be very good. For specific operation, add a small amount of rice with an appropriate amount of baking soda and water, mix it and pour it into the drain, and it will be ready after about 10 minutes.

2. Laundry detergent.

Laundry detergent has the ability to remove stains, as well as the ability to dissolve oil stains. If the kitchen drain is clogged with oil, you can use 3 cups of hot water and laundry detergent with a little vinegar, mix and pour into the drain.

3. Caustic soda. Caustic soda is highly corrosive and can corrode residues in sewer pipes, which in turn can unclog sewers. A basin of hot water, the temperature is about 60 degrees, put in an appropriate amount of caustic soda, fully fused, pour it into the sewer, about 20 minutes. Note that gloves need to be worn when cleaning, caustic soda is very corrosive.

4. Round wooden sticks.

Tie a towel to a round stick that matches the size of the sewer, put some water in the sink, and quickly pump the stick up and down, so that the garbage and oil clogged in the sewer will be stretched open, and the pipe will be unblocked.

Sewer blockage prevention methods.

1. Flush the sewer with a certain amount of boiling water every day, and the amount should be determined according to your own sewage discharge. This method can effectively control the adhesion of oil to the sewer.

2. Insist on diluting a certain amount of alkaline water once a week and pouring it into the sewer to prevent oil from forming lumps.

3. Be sure not to take away the sewer covering net for convenient speed, causing blocky objects to fall into the sewer. At the same time, it also prevents odors from being emitted by food rotting in the sewer.

For two days, I found that the kitchen was not draining smoothly (it had been used for more than a year), and the drainage was very slow, and I also complained that my family was not paying attention when pouring water, and did not clean up the impurities inside. So I found a special cleaning agent to clean the underwater, poured it into it according to the instructions, the situation was a little better but not completely improved, and yesterday I found that the drainage was not smooth, very slow and slow. Finally I couldn't bear it, and I dismantled the drain pipe and cleaned it again, only to find that the drain pipe had accumulated white hard lumps, full, not very hard, but it had been solid-stated, and it was finally poured out, and the whole pipe was silted up with this kind of thing, I searched from the Internet, and it was more credible that this solid thing was the kind of thing after the grease solidified and precipitated, and I didn't find a way to deal with this kind of thing.

The main reasons for this thing:

1.The design of the drain pipe is not reasonable. This distance from the inlet to the sink drain is too long, and there is a section that is horizontal to facilitate water deposition.

2.Lifestyle habits. If you often eat something very greasy, it will easily cause sediment when it is discharged into the underwater pipe.

The solution (has not been tested if it works):

When draining the greasy dirty water, pour in a detergent that can dissolve the oil, dissolve it for a while, and rinse it off with clean water.

Completely dismantled and cleaned, this may be the most effective way, of course, it is dirty, but there is no way, when purchasing kitchen drainage, you will choose some that are easier to disassemble, or you will not toss once tired and half dead. From the situation in my home coming year, the manual unclogging machine and detergent had limited effect and did not solve the problem at the root cause.

The best way to solve the problem is: when buying washbasins and vegetable basins, you must first see if the drainage is good and disassembled.

Continued: After actual repairs, it was found that the backwater bend of the sink was indeed not very useful, which affected the speed of water discharge and eventually caused blockage. However, if the rebate bend is canceled, it is easy to return to the smell.

All the use of a workaround method is to leave the drain pipe slightly longer point to use the drainage pipe to sagging to form a "backwater bend" to prevent the smell from rising, after a period of use proved to be very effective, the drainage is very smooth, and there is no smell.

What to do if the kitchen drain is clogged with oil and difficult to clean, this method can be used to clean quickly.

Soak it in boiling water for 10 minutes, or baking soda and boiling water can do it.

Connect the faucet and the drain with a water hose. Try to seal it all tight, or stuff it with something.。 Then turn on the faucet to the maximum... Generally, it can be flushed out with water pressure. The difficulty lies in how to seal it.

Pour some dish soap and laundry detergent into it, and after half an hour, fill a bucket with water and rinse it.

1. Boiling water, boiling water can effectively melt the oil remaining on the wall of the kitchen sewer pipe, and continuously pour boiling water into the sewer.

2. Baking soda + boiling water, baking soda is alkaline when dissolved in water, while the grease in the kitchen sewer oil will be hydrolyzed under alkaline conditions. You can pour baking soda into a pot of hot water and pour the baking soda into the drain slowly and continuously.

3. Pipeline dredging agent, there are a variety of ingredients in the special dredging agent that dissolve the oil stain, and it should be used according to the product manual.

4. Professional dredger, purchase a special dredger, insert the dredge into the sewer, and clean the oil stain of the sewer by rotating the dredger.

1. You can take a chemical method to prepare baking soda and white vinegar, mix it with hot water, and pour it directly into the sewer pipe, because whether it is white vinegar or baking soda, it can dissolve stains. Finally, we will see that the pipe mouth may be blistered up, which means that the pipe has been dredged, and if it is more serious, we can try a few more times.

2. You can take a physical method to prepare a round wooden stick, which is slightly smaller than the diameter of the sewer pipe, and can be stretched in. Poke it back and forth a few more times to dredge some of the oil in the pipeline. Finally, increase the hot water to rinse down, you can also use caustic soda, which is the same principle as baking soda and white vinegar.

3. If it is useless by chemical or physical methods, unscrew the joint of the water pipe, remove the hose, and clean up the blockage in the sewer pipe. In some cases, it is because dirt has accumulated inside, which has accumulated inside and cannot be dredged, so it will be more thorough in this way.

4. If you don't have baking soda or white vinegar or caustic soda at home, go to the supermarket to buy a pipe dredging agent to see if its composition is flexible, because if it is a strong acid and alkali, it is easy to corrode the sewer pipe.

This pipe dredging agent accumulates the performance characteristics of the dredging material, which is very easy to use, if the sewer pipe toilet has a clogging problem, just pour it a little and wait for the time to dissolve. If you turn on the faucet and flush it in about 15 minutes, you can solve the problem of slow draining.

1. Method 1: boiling water.

It is easier to wash grease stains from the bowl with hot water than with cold water. The same principle can be applied to a minor sewer blockage, flushing the sewer with boiling water, that is, using hot water to melt the oil remaining on the sewer pipe wall. Prepare enough boiling water (it is recommended to prepare a full pot of boiling water) and keep it continuously poured into the sewer.

2. Method 2: Baking soda boiling water.

Sodium bicarbonate is alkaline when dissolved in water, while the oil esters in oil stains are hydrolyzed under alkaline conditions. Take an appropriate amount of baking soda and pour it into a pot filled with hot water, and pour the baking soda into the drain continuously and slowly; You can also pour baking soda directly into the sewer, dissolve the baking soda with the water in the sewer, and after a few minutes, after a few minutes of baking soda and the oil ester of the sewer have fully reacted, pour it with boiling water, and it will basically be dredged.

3. Method 3: Use pipeline dredging agent.

If the method of boiling water and baking soda still can't dredge the sewer or the dredging result is not ideal, you can also choose to buy a special pipe dredging agent, which is sold in supermarkets and various shopping malls. This is because there are a variety of ingredients in these special dredging agents that dissolve the oil.

4. Method 4: Special dredging device.

At home, iron wire is generally chosen, but iron wire is not easy to operate at the bend of the sewer, buy a special dredge, insert the dredge into the sewer, and clean the oil stain of the sewer by rotating the dredger, and the sewer will be dredged.

5. Method 5: Leather picking.

To clean up the sewer oil, in addition to the special dredging device of method four, there is also a leather picker. By pulling the handle, a vacuum space is formed between the piston inside the leather tube and the sewer, and the continuous lifting handle generates pressure to suck up the clogged dirt in the sewer to dredge the sewer.

Method 1: Boiling water, boiling water can effectively melt the oil remaining on the sewer pipe wall, and continuously pour boiling water into the sewer.

Method 2: Baking soda boiling water, baking soda is alkaline when dissolved in water, and the grease in the oil will be hydrolyzed under alkaline conditions, you can take baking soda and pour it into a pot with hot water, and pour baking soda water into the sewer continuously and slowly.

Method 3: Pipeline dredging agent, there are a variety of ingredients in the special dredging agent to dissolve the oil, and use it according to the product manual.

Method 4: Professional dredger, buy a special dredger, insert the dredge into the sewer, and clean the oil stain of the sewer by rotating the dredger.

Method 5: Leather Lifter, through the lifting handle to form a vacuum space between the piston inside the leather barrel and the sewer, and continuously pull the handle to generate pressure to suck up the clogged dirt in the sewer.

Generally speaking, in winter, the kitchen drain is most likely to be unblocked, at this time, it can be judged that it should be caused by the accumulation and coagulation of grease, and relatively speaking, it is not a very serious blockage. At this time, you only need to boil the kettle and pour a pot of boiling water into the sewer pipe, at this time you can hear the sound of clattering, and the problem is generally solved.

2. Pipeline dredging.

There is also too much oil, which cannot be solved by using boiling water to dredge at this time, so you can consider a pipe dredging device sold on the street. When operating, you only need to hand crank the spiral steel wire and bring it out, so that a large amount of debris can be brought out. At the same time, you can also consider buying some alum, go to the sewer and use boiling water to shower, and after about 5 minutes, the sewer will be open.

3. Pipeline dredging agent.

If the above two methods still don't work, then the blockage may be too much. Consider buying a pipe dredging agent online. I believe we all know that there are still many reasons for blockage in the kitchen, including blockage, as well as grease, hair, kitchen waste (tea, vegetable leaves, etc.), and the use of pipe dredging agent is particularly good at this time.

1. First of all, it is necessary to remove the water outside the pipe mouth caused by blockage before the following operations can be carried out.

2. Then you can put this product into the pipe (about 50g in a bottle cap), and you must remember to flush it with warm water.

3. Here we should remind that the water added must be at the mouth of the pipe (you must know that the floor drain structure is to have water return, the purpose of this is to ensure that the dredging agent is also so that it can quickly remove the blockage, it is recommended to use the water pipe to pressurize the water flow and flush it quickly).

4. If it still doesn't work, then it is necessary to remove the stagnant water, and it is possible to repeat the operation according to the above actions, which is more suitable for serious blockage.

5. If it is used at 8 o'clock in the evening, then you can flush it at 8 o'clock in the morning, generally speaking, the water pipe has been dredged at this time.

How to deal with the blockage of kitchen pipes First of all, you can use the following methods;

1.Boiled water. Boil a large pot of boiling water and pour it directly into the clogged pipe; Then store a pool of hot water, and when it is full, pull out the plug and release the water.

2.Boiling water + dish soap.

If boiling water is not effective enough, you can add detergent such as dish soap, laundry detergent or laundry detergent to the boiling water, and then mix a large amount of detergent with boiling water to flush the pipe.

3.Pipeline dredging agent.

The main ingredient of pipeline dredging agent is sodium hydroxide, first pour the dredging agent into the blocked pipe, wait for one to two hours, and then pour in a basin of boiling water, which can basically be solved.

4.Dismantling and cleaning.

The most susceptible area of the kitchen to be clogged with oil is usually the "backbend", because a part of the water is stored in the "backbend" to prevent unpleasant smells. However, kitchen wastewater contains a lot of grease, which slowly accumulates in the "return bend" after cooling, and is easy to clog after a long time.

It stands to reason that under normal circumstances, the oil will not agglomerate, but in the case of narrow pipes, in the case of a colder environment, it may condense, there is no special way, the pipe is insulated, the pipeline is thickened, the sharp bends are reduced, etc., after the blockage, boil the water to irrigate, but this method depends on the location of the blockage, if it is far away from the drain of the hot water, and there is already water in it, it is not good, you can pass it first, wait for the water, and then pour hot water, pour more, hot water can dissolve the grease, but if it is scaling, That hot water is not good, how to get it has to be analyzed specifically.

Here's how to fix it:

Ingredients: 1 grapefruit peel, appropriate amount of hot water.

Steps: 1. Add the grapefruit peel and water to the pot.

2. Boil the grapefruit peel and water until boiling.

3. Pour the hot grapefruit peel water into the drain immediately and slowly while it is hot, which can effectively remove the sewer oil.

Flush down the water with boiling water, most of which are grease blockage, and the boiling water can be dissolved, flush into the waterway with a large pot of boiling water, put more laundry detergent in the water, and pour it into the pipe, it will be better. Then poke it with a thick iron wire a few times until the boiling water runs out.