Is it okay to use the membrane first and then use the waterproof glue?

Are you doing bathroom waterproofing.

Summary. Hello, it is possible to brush. When people go to the roof, they must take into account that there may be sharp objects, so they must make a rigid protective layer. However, considering that the aging life of the waterproofing membrane is not long, there may be water leakage in three to five years, so the scheme is:

1. Make 911 polyurethane on the surface of the coil, and then make a 3cm thick mortar protective layer on it;

2. Make a 3cm thick mortar protective layer directly on the membrane, and if there is a water leak after a few years, make a super elastic cracked self-closing waterproof coating on the protective layer;

3. (see this article) make a 3cm thick mortar waterproofing agent protective layer on the membrane (that is, add 5 waterproofing agents to the mortar). No matter which scheme is used, the protective layer needs to take into account the direction of the floor flow, the downpipe is at the lowest position, and the floor as a whole is sloped.

Can the membrane be brushed with waterproof paint?

Hello, it is possible to brush. When people go to the roof, they must take into account that there may be sharp objects, so they must make a rigid protective layer. However, considering that the aging life of the waterproofing membrane is not long, there may be water leakage in three to five years, so the scheme is:

1. Make 911 polyurethane on the surface of the coil, and then make a 3cm thick mortar protective layer on it; 2. Make a 3cm thick mortar protective layer directly on the membrane, and if there is a water leak after a few years, make a super elastic cracked self-closing waterproof coating on the protective layer; 3. (see this article) make a 3cm thick mortar waterproofing agent protective layer on the membrane (that is, add 5 waterproofing agents to the mortar). No matter which scheme, the protective layer needs to take into account the direction of the flow of water on the floor and the downpipe, and the whole floor is slope-like.

Thank you. You are welcome.

Summary. Yes, structural adhesive or waterproof coating can be used, and polyurethane should be used for waterproof coating. The key is that the waterproof coating mentioned upstairs should be connected with the waterproof material of the original ground on the one hand, and the casing should be glued firmly on the other hand, and if the gap is large, brush it several times, or add cement to fix it at the upper and lower ends.

Silica gel is a highly active adsorption material, insoluble in water and any solvent, non-toxic and tasteless, chemically stable, and does not react with any substance except strong alkali and hydrofluoric acid. It has high adsorption performance, good thermal stability, stable chemical properties, and high mechanical strength. Silicone is not only used as a special material in aviation, cutting-edge technology, military technology departments, but also in various sectors of the national economy, and its application range has been expanded to:

Construction, electronic and electrical, textile, automobile, machinery, leather and paper, chemical and light industry, metal and paint, medicine and medical treatment, etc. Structural adhesive refers to an adhesive with high strength, can withstand large loads, and is resistant to aging, fatigue and corrosion, and has stable performance in the expected life, and is suitable for bonding structural parts with strong strength. The structural adhesive has high strength, peel resistance, impact resistance, and simple construction technology.

It is used for bonding between metal, ceramic, plastic, rubber, wood and other materials of the same or different materials. It can partially replace traditional connections such as welding, riveting, bolting, etc.

Can you stick the waterproofing membrane with structural adhesive?

Hello dear has found the answer for you.

Yes, structural adhesive or waterproof coating can be used, and polyurethane should be used for waterproof coating. The key is that the waterproof coating mentioned upstairs should be connected with the waterproof material of the original ground on the one hand, and the casing should be glued firmly on the other hand, and if the gap is large, brush it several times, or add cement to fix it at the upper and lower ends. Silica gel is a highly active adsorption material, insoluble in water and any solvent, non-toxic and tasteless, chemically stable, and does not react with any substance except strong alkali and hydrofluoric acid.

It has high adsorption performance, good thermal stability, stable chemical properties, and high mechanical strength. Silicone is not only used as a special material for aviation, cutting-edge technology, and military technology, but also used in various departments of the national economy, and its application scope has been expanded to: construction, electronic and electrical, textile, automobile, machinery, leather and paper, chemical light industry, metal and paint, medicine and medical treatment.

Structural adhesive refers to an adhesive with high strength, can withstand large loads, and is resistant to aging, fatigue and corrosion, and has stable performance in the expected life, and is suitable for bonding structural parts with strong strength. The structural adhesive has high strength, peel resistance, impact resistance, and simple construction technology. It is used for bonding between metal, ceramic, plastic, rubber, wood and other materials of the same or different materials.

It can partially replace traditional connections such as welding, riveting, bolting, etc.

The stress distribution of the joint surface is uniform, and there is no thermal impact and deformation of the slag modified parts. Structural adhesives are widely used in engineering, mainly used for reinforcement, anchoring, bonding, repair, etc. Such as sticking steel, sticking carbon fiber, planting reinforcement, crack reinforcement, side sealing of dense trouser beams, hole repair, road nail pasting, surface protection, concrete bonding, etc.

Self-adhesive waterproofing membrane can be constructed in the house in winter, and it is only necessary to keep the indoor temperature suitable for construction.

Introduction to the use of self-adhesive waterproof membrane: the laying base layer needs to be cleaned, and the base treatment agent should be applied to the base layer, and wait until it is cool to touch with your hands. For nodes, detailed nodes, yin and yang corners, etc., it is necessary to strengthen waterproof treatment according to the specifications.

After the baseline is drawn, it is necessary to carry out the pre-laying of the coil, and it is necessary to pay attention to the paper separator film facing downward. When paving, roll up the coil from one end to 1 2 places, and then use a paper cutter to cut the separator film from the middle, but not scissors rolls. Then pull the torn isolation paper head and pull it back evenly, and lay the coil while pulling, and pay attention to the exhaust.

As the name suggests, self-adhesive waterproofing membrane is automatic bonding, and self-adhesive waterproofing membrane has the following construction methods:

First: dry paving method. That is, the base layer is dry, which requires the base layer and the base treatment agent to be constructed, and it must not stick or firm.

Second: wet paving method. Even if the cement element will be used as the medium for bonding, the effect is very good, as long as there is no open water can be constructed, but if it is cold and frozen in winter, it can not be constructed, unless the operation is faster.

Third: hot melt method. The hot melt method mentioned here is not like the construction of asphalt membrane, as long as it is heated slightly on the basis of the first article.

The following is the self-adhesive waterproofing membrane hot melt construction**, as well as dry and wet paving**. You can see it at a glance.

Hot melt method: dry laying method:

Wet paving method:

Summary. Use the membrane as the waterproof material The waterproof is the membrane or the glue below! Hello, glad to answer for you.

The waterproof material made of membrane is as follows: waterproof membrane is mainly used in building walls, roofs, tunnels, highways, landfills, etc., to resist external rainwater, groundwater leakage can be curled into a roll-shaped flexible building materials product, as a non-leakage connection between the engineering foundation and the building, is the first barrier of waterproofing of the whole project, and plays a vital role in the whole project. The main products are asphalt waterproofing membrane and polymer waterproofing membrane.

Hope mine can help you! Do you have any other questions?

Use the membrane as the waterproof material The waterproof is the membrane or the glue underneath.

Use the membrane as a waterproof material Waterproof is the trapped branch dress membrane or the glue pro below! Hello, glad to answer for you. The waterproofing material made with the membrane is as follows:

Waterproofing membrane is mainly used in building walls, roofs, and tunnels, highways, landfills, etc., to resist external rainwater, groundwater leakage can be curled into a roll-shaped flexible building materials products, as the foundation of the project and the building between the non-leakage connection, is the first barrier of the whole project waterproof, plays a vital role in the whole project. The main products are asphalt waterproofing membrane and polymer waterproofing membrane. Hope mine can help you!

Do you have any other questions?

What is the role of the glue underneath the coil.

Adhesives for bonding coils to waterproof substrates;

The waterproof membrane can be directly used to pave the tiles with tile adhesive, and it is recommended to use Keru Dashun C300 reinforced tile adhesive. Keshun C300 reinforced tile adhesive is made of cement, refined fine aggregate, and added polymer and a variety of special additives to prepare slag. The product has excellent water retention performance, which is more convenient and faster than traditional cement mortar construction.

The product has good adhesion to medium-sized tiles. Pay attention to the following details when pasting tiles on the waterproof layer: 1. Precautions for tiling.

Be sure to bricklayer the wire, and lay the level, be sure to use tools to control the quality. 2. Adhesion. Be sure to use adjunct materials that are sufficiently adhesive for paving.

3. Inspection and acceptance. Be sure to use a level or a Yunzi aluminum alloy ruler for inspection. 4. Prevent hollowing.

It is best to wait 2-3 hours before checking the hollow drum of the tile, especially to pay attention to the four corners of the tile, which must be reworked when the hollow drum is heard.

Summary. The membrane waterproofing needs to be done to seal the seam waterproof.

The membrane waterproofing needs to be done to seal the seam waterproof.

This must be done by professional staff, the waterproofing membrane is prefabricated in the factory and has a fixed thickness. However, when leaving the factory, it is still a "semi-finished product", which needs to be laid on the base layer at the construction site through a certain Shi Fiber Ming Gong process, and finally form a continuous, intersecting sealing and closing waterproof layer.

The on-site installation of flaky waterproofing materials requires seams on the long and short sides to ensure that the waterproof layer forms a whole.

This must be unsealed, sealed and waterproof.

Got it. Uh-huh.

The seam sealing inspection batch should be calculated by meters.

Count the number of meters of the entire coil or the length of the seam.

Seam. Oooh.