Is it okay to replace the three light strips with one in the middle and connect those two?

Of course not, because there are three people on it, and if you change one in the middle. Connect them and you'll call.

If there are three daily lines, you can't change one in the middle and connect the other two, so you need to see which is the live line, which is the zero line, and which is the ground line, so that you can.

This should be possible to connect, and under normal circumstances, the three of them are connected to each other and can be plugged in directly.

Three of the light strips become two, it should be okay. Just pick it up from end to end.

In this case, it is definitely possible, as long as there is this quantization or there is a current passing through, it can definitely be done directly.

Now the light strip is generally said LED light strip, if the middle one is replaced, we just need to replace the middle one and replace it with a new one. Then I connected the three strips of light and it was fine.

The 1000 of the year is under the sister and brother, he can not pick up, but he can't connect to any other line, so there are potential safety hazards.

Just now, there are three in the middle of the change, it's okay to pick up those two, but if not, it depends on whether he can meet some of your needs.

Can it be carried out until you borrow it? He is the meaning of the tandem, the tandem will not work, it must be rammed.

There are also three nets in the middle, can the two be connected? No, you can't.

Can you take three people, and change one in the middle, is it okay to connect those two? This should be a no-no.

Is it true that there are three in the middle and one in the middle to connect the other two? OK?

Hello dear, according to the situation you described, how to connect the three-wire LED lamp to 2 lines steps: 1. Shout the judgment first confirm whether the LED lamp itself has a logo, and there is a logo to wire according to the logo. If there is no identification, confirm whether the yellow line is a yellow-green two-color line or a single yellow line, and the general yellow-green two-color Bi permeation cavity line is the grounding wire.

2. Connect the current-limiting resistor source with the positive wire of the power supply, and then separate the wires connected to the LED tube. 3. Use the peeler to remove a short section of the negative electrode of the lamp, and remove the negative line of the LED lamp after removing the wire. 4. After that, connect the positive pole of the power shirt lamp with the negative pole of the LED with the peeled off, and connect the positive pole of the power supply with the positive pole of the LED tube.

5. In this way, the line of the LED tube is connected, and the third wire is the ground wire, which cannot be used in actual use.

Two strips of light can be used for one route; As long as the line load is sufficient, it can be celebrated; The low-voltage soft light strip only needs to connect the wires at both ends, and the hard light strip needs to be connected at the corner, and the high-voltage light strip needs to be connected in the middle of the needle, depending on what your light strip is, prompt: the low-voltage light strip is best connected in parallel, the series is too long, and it is easy to produce a voltage drop, resulting in uneven brightness of the light strip.

Lamp cracked tape has been widely used in buildings, bridges, roads, gardens, courtyards, floors, ceilings, furniture, cars, ponds, underwater, advertising, signboards, signs and other fields, used as decoration or lighting, Yu Zaoji to a variety of festivals, such as Christmas, Halloween, Valentine's Day, Easter, National Day, etc. It is widely used in building wheel corridors, bridges, guardrails, hotels, forest gardens, dance halls, advertising decoration places, etc.

1. Generally, there is only one live wire for each civil electricity house, and the two live wires are still the same phase wire, and the phase voltage is 220V, but there is no zero line can not be formed into a circuit to check and touch, and the lights can not be lit without voltage at both ends.

2. If it is two different phase wires (live wires) in three-phase electricity, the line voltage is 380V, and the two lamps can be connected in series with the switch to form a circuit, and each lamp can be lit up by leakage at about 190V.

It can be used, but the light strip needs to be shared by a single circuit.

You can use all the way, I don't know if you need to start together.