How to check the hard drive, press enter directly?

Generally speaking, when checking the hard disk, there will be a corresponding prompt on the screen, and you can operate according to the prompt, such as checking the disk when you turn it on, and you can ask him to check it automatically.

To verify if the hard drive has bad sectors, you can use a tool software, such as the system's built-in "ScanDisk" disk scanner. However, the scanning speed of this software is slow, it is recommended to use "Efficiency Source Hard Disk Bad Sector Detection Software" to scan. "Efficiency Source Hard Drive Bad Sector Detection Software" can test various brands of hard disk products on the market.

+ r to open "Run", enter "cmd" in Run, and press enter to enter the command line.

2.Enter the command: wmic diskdrive get serialnumber

to find out.

2. In the main page of the software, find the lt in the lower right corner; Disk Detection Click to open.

3. Here you can choose to detect the whole disk or individual partitions.

4. Then click LT; Start scanning the GT and the software will perform a systematic analysis of the disk.

5. When the software finishes scanning the disk, the scan result will be displayed.

Checking the hard disk is not something that can be done by pressing the enter key, he needs some professional hard disk detection tools to detect the hard disk, which can find out whether there are bad sectors on the hard disk or there are some file errors.

To check the hard drive, you have to click on my computer right click, then press Properties to see how big your hard drive is, and then click on the properties at the bottom to get inside the hard drive.

Don't know what you're checking your hard drive? If you want to check your hard drive for bad sectors. Right-click on the hard disk that needs to be checked. Select Properties. Tool of choice. Then click Check.

Under normal circumstances, your last shutdown may have been performed illegally. (For example, if the power is turned off, press the power button directly to turn it off.) And so on).

The system performed a hard drive self-test on the second boot. This property is normal: press enter, press f8 to select the last correct configuration to enter.

Normal shutdown.

If you shut down normally every time, there is still disk detection at startup. Then there is something wrong with your hard drive.

Either there are logical bad sectors or there are physical bad sectors.

After booting the computer on the system CD, select Enter the Failure Recovery Console and run chkdsk fr

If you still have this problem after running this command, then it is recommended that you format the entire hard drive once as soon as possible before partitioning the system.

Format the hard drive.

The hard disk is formatted, and the system is extremely unstable when using the computer, and it is often rebooted, and then the disk is scanned. Open the Event Viewer with a whole bunch of warnings

The event is NTFS, which indicates that the file system is abnormal. However, the contents of the disk can be accessed normally in Windows, just in case the format is up.

In the actual use of the computer, Windows may have some system failures due to crashes, abnormal shutdowns, etc. Necessary investigations should be carried out to address these failures and appropriate measures should be taken. In daily use, you should try to avoid incorrect operations, and make off-site backup of important files in the hard disk to minimize losses.

To run from start->, enter:

chkdsk /f /r

In the pop-up cmd window, press Y to restart your computer.

After rebooting, it will automatically go into detecting and repairing hard drive errors and proofreading files for him to complete.

Although you shut down normally, but there was an abnormal shutdown before, and you skipped every time you detected and repaired, that is, the hard disk will be detected every time you boot up, no matter how long it takes, only let him complete it.

There is no way to detect the C drive under Windows, it is possible that your system is running too many active programs. You can also go into safe mode to organize or minimize the number of programs that run after logging in. If you have hidden Trojans on your computer, it is more likely that you will not be able to defragment, so you need to optimize your system.

It's best to do the above steps first, and then take a look.

Before the self-test, there will be a prompt to check and not check, generally ten seconds, press any key to skip the self-test, but I recommend the self-test.

If you have such a problem because there is no normal shutdown, you can optimize the system with Optimizer, which may solve this problem.

Wait patiently for it to enter the system after checking,If it shuts down normally,It shouldn't be testing next time.,You can try.。

What you are talking about is the system detection when the system is turned on at startup, which means that there is a problem with your system, or you performed an incorrect shutdown operation last time, if this problem often occurs, then you should pay attention, there may be a big problem.

You can pay attention.

This is because your disk is fragmented.

To defragment the disk.

This will not happen after tidying up.

Enter the number of the disk you want to detect, this number describes the position of the hard disk on the interface, be careful not to enter the number of the optical drive as the hard disk.

This should be Windows disk detection

That's because the system detects an abnormal shutdown and automatically checks for disk errors.

to skip disk checking press any key within 10 second

The meaning of this sentence is: If you want to skip disk detection, press any key within 10 seconds.

So when you press any key, the disk will not detect itself and will go directly to the system, but if you don't press it, then the disk will perform a self-test. I suggest that you do a self-test.

Generally, it will appear at the next boot of the abnormal shutdown, if it is a normal shutdown every time, it is generally a problem with the system, try a new system.

This is the number that tells you to choose the hard drive!

You see the number in front of your hard disk above, you just enter the number and then press enter, you can scan the disk you selected, note: don't use the optical drive as a hard disk.

1. Check the motherboard battery and reset the BIOS discharge if necessary.

2. The master-slave settings of the hard disk are incorrect, and the BIOS cannot find the correct boot, it is better to set the BIOS as well

To press f1 to start: There are several reasons:

1. The CMOS parameter settings are incorrect

Floppy drive: If the floppy drive is not detected, please check whether the data cable is connected, and then see if the settings in the BIOS are correct: check the settings of the boot sequence; In addition, if there is no floppy drive, it is directly shielded.

Keyboard: Some CMOS settings in the keyboard problem will also appear press F1 to boot the situation, the landlord to check it himself.

Memory: Disable Memory Verification.

2. Prompt for insufficient BIOS battery power - replace the battery 3. Jumper setting problem - refer to the manual to set.

press f1 to resume

In addition, it may be a non-fatal hardware error that can be replaced with a check.

The master is never right, it will only detect one disk, your battery is dead, replace it! Five yuan, everyone in the world knows!

You need to set the default primary disk.

Has the master-slave relationship between the two disks been set?

Here's how to repair portable hard drive with chkdsk disk repair tool:

1. When this prompt appears, click the start menu in the lower left corner of the computer and find Run.

2. Click Run, you can see the running interface.

3. Enter cmd in the run box to open the administrator interface.

4. When opening the administrator interface, first of all, confirm the drive letter displayed on the computer, and you can see the display disk in the computer: g

5. Then go to the management interface and enter **:chkdskg: f (it should be noted that the g in ** represents the drive letter of the mobile hard disk, if your display is h, then replace g with h).

6. Press Enter to confirm, and the mobile hard disk will be repaired.

chkdsk is a built-in file repair command, you can follow the following steps to repair the file:

1. Take out the SD card and connect it to the computer with a card reader so that it can be displayed on the corresponding disk.

3. After the repair is completed, the DOS window will be automatically closed, and the corresponding SD card can be opened directly to find the files we need to recover.

If the chkdsk command cannot repair the damaged portable hard drive, it is recommended to use professional data recovery software to repair the data, and the specific operation steps are as follows:

2. Select the location where the original data file is stored, you can directly select the disk where the corresponding data was deleted by mistake, and click "Start Scan" below to automatically format and scan the SD card.

3. Wait for the scanning to end, then you can select the files we need to recover in turn according to the form of file type, and click the "Recover" option below to retrieve them.

You can open the command and enter the command to repair the portable hard drive.

Look directly at whether your hard drive light is on.

If it is light, it is still detecting the repair of the hard disk sector.

If it does not light up for a long time. Then the note is dead.

chkdsk can only fix bad logical sectors.

Useless against physical bad sectors. There is also a danger that bad sectors will increase.

Secondly, the repair time of 4TB with CHKDSK is very long.

I used to run for nearly 9 hours with 1TB disk repairs.

And you have a lot of documents. Small volume has a lot of data. The more fragmented disks are, the longer it will take time.

Always showing up, drive, path or file name is invalid, what to do?

Open cmd, and if your portable hard drive is a G drive, type chkdsk f g: enter.

Mac OS X's Disk Utility data recovery method is to use the recovery function of Disk Utility, you can clone the entire disk and copy the contents of one hard disk to another in its entirety.

When the system fails, replace the clone drive or connect the clone drive via Firewire, you can boot with the clone and you can use the machine immediately.

You need to use a different boot hard disk or disc to boot up, and then back up the original boot disk, which often needs to be stored on a third disk.

Suppose you start with the system installation ***, back up the internal hard disk of the machine, and store the backup on a mobile hard disk, ***, the internal and mobile hard disks together are three disks.

Disk Utility for Intel architectures must use a running system to clone the entire disk.

If you boot with a system installation, Disk Utility inside *** does not allow you to select a destination or source volume.

It still hasn't recovered, and I wonder who has recovered.

Is there any hint that it doesn't open properly? Press the enter key to open it, which means that your system is fine. It can be used normally.

If it starts again after normal shutdown, it is not normal for this situation to occur, if there is a time countdown, it is normal to start the return button within the countdown time.

The motherboard battery is dead, just change the battery.

You should have hibernation or hard drive hibernation mode enabled, that's why it's like this.

The Japanese computer can't be turned on normally, can I press the enter key to open it? Does it work? I just have to play, if I don't open it, press the enter key to restart it should be fine.

The laptop can't be opened normally, but it can be opened by pressing the enter key, can it be used normally? You can ask about the after-sales service, and he will tell you one by one.

You don't understand what you said.,Generally, the main boot partition is damaged or 2 hard disks are set up to conflict with the main disk.,Generally, you need to redo the system.,If there's a problem, thank you for adopting.。