If the wipers of the car are broken, what should I do on a rainy day?

You should reinstall it on a rainy day, and after all, there may be some dangers in such a situation, and there is no way to see the road ahead while driving, so be sure to pay attention.

This can be alleviated by applying soap to the glass surface, and the road surface can be observed in this way. The safest thing to do is to approach the side of the road, pull over, turn on the marker lights and double flashes, hazard signs, and wait for the rain to light before driving.

We can put some soapy water on the windshield of the car, and then we can use the power of the rain to clean our windshield.

Try not to drive on rainy days, because if the wipers cannot be used in time, it will affect your driving vision.

If the wiper is broken, it must be repaired in time, after all, the wiper is also very important for the car, and it also plays some decisive factors, do not drag it out of repair.

The wiper assembly is equipped with an electric motor, a reducer, a four-link mechanism, a wiper arm journal, a wiper blade assembly, etc. When the power switch of the wiper is pressed, the motor runs, and the speed ratio of the motor pushes the lower swing arm through the speed reduction and torsion increase effect of the rack and pinion, and the lower swing arm drives the four-link mechanism, and the four-link mechanism drives the transmission shaft installed on the front cover plate to shake up and down, and finally the wiper blade is driven by the transmission shaft to sweep the windshield of the car.

Common faults in any position of the wiper assembly will definitely cause the abnormality of the wipers. The wiper may not move because the fuse is broken, so the wiper can't move, so you have to open it to take a look, if so, just replace it.

You can refer to the following methods to find the problem.

Open the lead cover to see if the drive link is out of place (this is the most common cause).

Check that the fuse is in good condition.

Disassemble the motor cord plug to turn on the power supply, and use a multimeter to measure whether there is voltage.

If the fuse is intact and the motor has no voltage, check whether the circuit and turn signal combination switch is intact.

Generally, the motor will have a burnt smell when it burns out.

If you turn on the power supply and measure the normal voltage at the wiper motor, you can consider that the motor is broken.

Pay attention to whether the pole is connected to the wiper rocker arm in the correct way. Some of the arms are screwed to the rocker arm, while others are locked with a buckle.

Pull the wiper up and touch it with your finger to check for damage to the cleaned rubber wiper and the elasticity of the rubber blades. If the blades are aged, hardened, or cracked, then the wiper is broken.

During the test, the wiper switch is placed at various speed positions to check whether the wiper maintains a certain speed at different speeds. Especially in the intermittent working state, it is also necessary to pay attention to whether the wiper maintains a certain speed when it is in motion.

Check the wiper status and whether the wiper rod has uneven swing or leakage. If the following three situations occur, it means that the wiper is unqualified: first, the swing is not smooth, and the wiper is not beating normally; Second, the contact surface of the rubber and the glass surface cannot be completely fitted, resulting in wiping residue; Third, after wiping, the glass surface presents a water film state, and fine stripes, fog and linear residues are produced on the glass.

During the test, attention should be paid to whether there is abnormal noise in the motor, especially when the wiper motor is humming and does not rotate. This indicates that the mechanical transmission part of the wiper is rusted or stuck, and the wiper switch should be turned off immediately to prevent the motor from being burned.

Wipers are intolerant automotive products that can easily be replaced due to aging。The structure of the wiper is very simple, mainly a brush and a motor, and there are relatively few failures. Even if the wiper fails to move, most of the time it is because the fuse has been blown out.

Wiper repair: As long as you open the fuse box, find the fuse of the wiper, pull it out and replace it, and you can continue to use it. There are two main types of fuses: chip fuses and glass tube fuses.

The point of the wiper for the car:

It is used to brush and scrape the rain and dust attached to the windshield of the vehicle to improve the visibility of the driver and increase driving safety. Because of the legal requirements, cars in almost all places carry windshield wipers.

Vehicles such as hatchbacks and minivans are also equipped with wipers in the rear windows. In addition to automobiles, windshield wipers are also installed in other means of transportation, such as trains and trams. Some construction equipment, such as cranes, are also equipped with wipers.

After using it for a little longer, there will be various small problems with the car wiper, and replacing it is of course the best measure, but we also have to analyze the reasons and know what to do. Generally speaking, the wiper of a vehicle will have the following fault phenomena: Fault 1:

Fine streaks, fog and linear residues are formed on the glass.

Causes: Attachment of foreign bodies, sand, dust or damage to the triangular tip of the triangular edge.

Solution: Clean the sharp edge or replace the wiper blades.

Fault 2: The swing is not smooth, and the wipers are not beating normally.

Reason: The tip of the wiper blade is curved and wavy, and there are other attachments such as wax or oil film on the glass surface.

Solution: Wipe the glass part clean or replace the wiper blades.

Fault 3: The contact surface of the rubber and the glass surface cannot be completely fitted, resulting in wiping residue.

Cause: After a long period of use, the rubber hardens and loses its elasticity or breaks.

Solution: Replace the wiper blades Custer.

Fault 4: After wiping, the glass surface is in a state of water film.

Reason: Deformation of the wiper rod due to rust or external force.

Solution: Replace the wipers.

The wiper of the car is broken, how can I fix it myself?

It may be a problem with the wiper motor, and you need to change it.

It may be that the rubber strip is aging, generally when there is no water and dry friction, the resistance is too great, and the wiper motor can not drive the load, which will cause the motor to stall, at this time, the motor stall current is very large, and the motor is easy to burn out for a long time. Of course, the high-end car motor will be overheated and protected, so it will not break so easily. Unless the parts inside are failing.

The wipers of the car are broken, and you should drive to the repair shop to repair the wipers on a rainy day. Wipers are pieces of rubber wrapped in iron sheets that are inserted into the end of the rocker arm in an embedded manner. So after a long time, the wiper blades will fall off, causing the end of the swingarm to rub directly against the windshield, which will not only blow rain, but also scratch the glass.

It's not often that two wiper blades come off at the same time. If it is the left driver's seat, you can remove the wiper blade of the right passenger seat, install it on the left side, and then find a cloth to wrap the wiper head on the right, or remove the rocker arm to avoid scratching the windshield.

1.If the windshield wiper fuse is broken, you can find the car's fuse box. Usually, the fuse box is located on the head side of the vehicle close to the battery.

Once the fuse is opened, find the wiper fuse from the logo on the back of the fuse. Take out the wiper fuse with a fuse clip and check for burnout. Make sure the wiper fuse is blown, locate the location of the spare fuse from the sign on the back of the box, and note the amperage of the fuse to be replaced, a short circuit may occur if the fuse is not replaced properly.

Start the wiper switch and check if the wiper is working properly.

2.Stains on the wiper blades and glass surface of the wiper can also cause the wiper to move slowly; If the voltage entering the permanent magnet motor is low, it may be that the line contact is poor. Check for poor contact between the line and the wiper lever.

Check if the carbon brushes are used up. If the carbon brush is too short, the pressure will be too low and the direct contact between the carbon brush and the commutator will be poor. Insufficient lubrication of wiper permanent magnet motor bearings and reducer can also lead to poor rotation, only oil or grease needs to be added.

3.If the wiper fuse is not broken, it is very likely that the wiper motor has failed, and the motor failure is unlikely to resolve itself. It is recommended that the owner of the car take care of it to the garage.

If it rains while driving, you should try to avoid driving, because if you don't have a wiper to wash the windshield water in time, it is easy to disturb the driver's vision. The above is the answer to the question of how to drive on a rainy day if the wiper of the car is broken.

After the wiper of the car is broken, you should go to a professional repair company or 4S shop for repair as soon as possible. Otherwise, it will cause blurred vision on rainy days, and accidents can easily occur.

When the wiper is broken, be sure to reduce your speed, and in case of emergency, step on the brake in time to avoid accidents.

On rainy days, you should control your speed properly, pay attention to the road conditions, park your car in a safe area, and wait for the rain to pass before driving.

Summary. If the wiper is broken when driving at high speed on a rainy day, it means that you can only go down at high speed. That is to say, the service area closest to this high-speed port, and then parked in the service area, generally there are service areas with this maintenance, that is, there is this car repairer let him check it for you, if there is really no way to repair, then you can only go low speed, and then find a nearby repair shop to check the maintenance process, do not go on the highway again.

On rainy days, the speed of this car is particularly fast, when it rains, this windshield is not clear, this rain is very dangerous, it is easy to have accidents, it is recommended to go at a low speed, and then go to the repair shop inside.

What should I do if I am driving on a high speed on a rainy day and the wipers are broken?

Hello, I'm helping you sort out the answers to your questions, please wait a while The wipers are broken when driving at high speed on a rainy day, which means that you can only get off the high speed. That is to say, the service area closest to this high-speed seepage mouth, and then parked in the service area, generally there are service areas with this maintenance, that is, there is this car repairer let him check it for you, such as Cong Jue said that there is really no way to repair, then you can only go at low speed, and then find a nearby repair shop to check the maintenance process, do not go on the highway again. On rainy days, the speed of this car is particularly fast, when it rains, this windshield is not clear, this rain is very dangerous, it is easy to have accidents, it is recommended to go at a low speed, and then go to the repair shop inside.

The wiper of the car is broken, and of course it can be repaired by itself, but when repairing, we should pay attention to the ways and means, and don't repair it more and more.

How to repair the wiper if the glass is not clean? The wipers of the car can play a very good role in the driver's driving of the car. However, wipers are not resistant to car products, so they often deteriorate or malfunction.

If the wiper can't wipe the glass clean, it is often because the rubber contact surface of the wiper cannot fit perfectly with the glass surface, in this case, we need to remove the wiper blade and replace it. Be careful not to tear the wipers during the replacement process.

The wiper is not beating properly, how should it be repaired? If the sharp blade part is curved or wavy, it proves that there are debris on the glass surface of the car, as long as the debris on the glass surface is wiped clean with a clean rag. If the wipers are bent too much, the wipers need to be replaced.

After the wiper is brushed, fine lines appear on the glass, what should be done? After the wiper is brushed, the reason for the fine lines on the glass is basically the same as the reason for the deformation and abnormal beating of the wiper, which is caused by the residual debris on the glass. When we remove debris from the glass, we also need to remove debris from the triangular tip of the wiper.

What should I do if the glass gets more and more muddy after wiping the wiper? Sometimes, we turn on the wipers on a rainy day, only to find that the wipers are getting more and more sticky on the glass, and this is because the wipers are rusty. Wipers are a consumable, so we must pay attention to maintenance in the process of using wipers.

What should I do if the wipers won't move? The wipers won't move, most of the time because the fuse is blown out, we need to open the fuse box and find the fuse of the wiper to replace it.

OK. Because the wiper is broken, just buy a new wiper and replace it, it's very simple, so you can repair it yourself.

It is not possible to repair it by yourself, because you can't repair it yourself, and you need to replace the wipers, just go directly to the repair shop.

It's not that you can't fix it, it's that you can't fix it yourself, because you can only replace the wiper when it breaks.

How to deal with wiper damage: 1. It may be that the fuse is blown out, just open the fuse box and replace the fuse again. 2. After the glass tube fuse is blown out, it can be temporarily replaced by wrapping the tin foil in the cigarette on the glass tube a few times.

3. If the wiper is suddenly damaged, you can apply soap to the windshield to maintain a clear vision for thirty or forty minutes. 4. The wiper is wrapped with a rubber sheet by an iron sheet, inserted at the end of the rocker arm in an embedded way, the wiper blade falls off for a long time, and the rocker arm will directly rub the glass, not only can not clean the rainwater, but also scratches the glass, if it falls on the left, the right wiper blade can be removed and installed on the left side, and the right wiper head is wrapped with a cloth, or the rocker arm is removed to avoid scratching the windshield.