How do you connect the wires that are wrapped in three wires and become one in the middle?

The connection method of the cable TV wire is broken in the middle: 1. It is generally recommended to replace a new signal connection cable to ensure the stability of signal transmission; 2. You can also connect the wire end of the two-dash line to two signal plugs, and then check the plug to the signal connector to realize the connection.

In this case, the noodle wire is broken, and you need to get the rubber on both sides open and screw the two wires together.

But the outside must be wrapped with an electric insulation tape.

This situation will affect the correct connection of the circuit, after the middle one is broken, you only need to reconnect the line, and then complete the circuit closure.

If the middle is broken in the process of wiring, you can cut the two sections a little shorter, and then it can be over.

I wrapped three wires, and the middle of one wire was broken, how to connect it back? First of all, you have to check that it is broken? Then deal with the broken place. Then you can go back again.

Then this is more troublesome, you have to determine which wire is broken, and people have to untie it to find this location to connect it!

Then, of course, you need a chance, if you want it, and then it's very good to earn it back yourself, one thing.

Where is that? And what happens after the epilepsy hospital is broken? If you take it back, you can use the connection intermediate tube to connect and restore it.

This can be picked up through his related situation, and it should be very easy and very convenient.

How about exposing three wires, and one wire stands in the middle of the road? Take it back, put it at the east gate, and I'll pick it up again for you.

The three lines are broken together, and this must be disassembled and reconnected.

If you run three wires, then under normal circumstances, if it becomes one wire, and if it breaks in the middle, I suggest you repair it again, which may be relatively better.

I wrapped three wires and formed a wire, and it was broken in the middle, how to connect it back? You can find this, you see**? Well, and up, can you just take it apart and pick it up?

See why they just broke and figured out how they connected.

If you wrap three wires and turn them into one wire, they break in the middle, and you may have to find a professional to help you repair them.

After three wires merged into one wire, how to drop the price if it is broken in the middle, this is in a hurry. Movie.

Hello friend, I wrapped three wires, turned into one wire, and if it was broken in the middle, it could be directly connected back.

Wrap three wires, become a wire, if the middle is broken, you can directly connect it back, the live wire and the live wire zero line to the zero line.

I don't think electricity is such a thing as a fool of yourself? It's better to find a professional electrician to get it for you.

Some news about the parallel connection of the 3rd wire, a professional electrician will tell you.

What should I do if I get to three wires and one wire, and it breaks in the middle? I think it should be completely demolished.

Wrap three wires, turn into one wire, and only connect it when it is broken in the middle.

When the wire is broken, it is necessary to peel a certain length first, and then cross to let the peeling of one end be wound more than 7 times on the line at the other end of the clockwise version, and finally let the remaining right end also be wound in accordance with this way, pay attention to the tight winding with pliers and other tools when winding, so as not to cause loose oxidation in use and poor contact. In this way, after winding, it is enough to make two layers of insulating tape and waterproof tape on the outer layer. It doesn't matter if the treated wire is installed on a small load electrical equipment, whether it is a live or neutral wire, but it is not possible to connect it to a large load circuit.

Hello, it is a pleasure to serve you and make the following decoding hand answer for you: If the cable is broken twice, can it be connected? The answer is yes, but be safe.

The workaround and practice steps are as follows:1First, inspect the broken cable to make sure it is not damaged, has not touched other cables, and has no damaged insulation.

2.Then, use the wires to connect the disconnected cables together separately to ensure that the wiring is correct, that it does not touch the cable, and that there is no damaged insulation. 3.

Finally, the wiring is secured with tape to prevent loosening of the wiring and short circuits between the cables. Personal tip: When wiring, always make sure that the wiring is correct, that it is not touching other cables, and that there is no damaged insulation to avoid potential safety hazards.

1. It is very important to remove the electric switch, and warn the people around you, especially children, that the circuit is under maintenance, and the electric switch is not allowed to start.

2. Find the broken thread and determine which one is connected to which.

3. Leak a part of the end of the connected wire to ensure that it can be screwed together. It can be burned with a lighter, the skin can be peeled off with diagonal pliers, and sometimes it can be cut with scissors, depending on the type and material of the inner envelope.

4. After the thread head leaks, screw the thread head together.

5. Move the switch to confirm whether it has been connected, connected, and there is electricity. Then remove the gate again.

6. After confirming that the OK is completed, use insulating electrical tape to wrap the connected place and the left and right parts, and wrap it twice, pay attention to the length of the wound must be wider than the connection, and there can be no floor winding place, so as to prevent leakage and other wire contacts or water ingress.

7. If the two connections are staggered, try to stagger them to prevent short circuit or danger after the adhesive tape falls off.

After the wire is wound, the electric switch can be moved up and there will be electricity normally.