Can I still use it if the water enters the socket and it feels leaking? 10

The socket is flooded, and at the same time, it feels like there is a leak! Then you can't use it for the time being!

Receptacle. The socket is flooded, so hurry up and clean it up! After cleaning up and drying, plug it back in and continue to use it!

From now on, be sure to pay special attention to waterproof and moisture-proof when using the socket! Don't repeat the mistakes of the past!

Remember: the biggest taboo of all electrical appliances is that the water gets damp!

Can I still use it if the water enters the socket and it feels leaking? Yes, but you should let it dry before using it. If the water ingress is serious, the panel needs to be opened for cleaning, in short, there can be no water residue.

Re-purchase the socket to install, the socket water should be dealt with immediately, otherwise it will lead to leakage accidents.

Pay attention to check the inside of the socket before use, such as water inside the socket, stained with dirt and dust, at this time it is best to clean it up before use, do not touch the socket when your hands are wet, you can set up some sockets with switches, so that you can cut off the power supply without pulling the plug, and to a large extent avoid direct contact with the power supply.

It does not affect the use of drying.

After the socket is flooded, accidents such as leakage and short circuit will occur due to the conductive effect of water.

After drying, the water is gone, and the premise of affecting use does not exist, so it is of course no problem to continue to use.

After the plug and discharge are flooded, the plug should be pulled out in time to prevent short circuit and leakage. The plug can still be used again after drying, and the premise is to make sure that the inside of the plug is completely dry and the normal insulation is restored.

If you put in a very small amount of water, drain it and dry it thoroughly before you can continue to use it. It is best to take it apart and dry it, or use a hair dryer to dry it.

No matter how you deal with it, be sure to cut off the power supply. Avoid electric shock.

It is recommended not to use the socket after it is flooded, as the use of the socket after the water is flooded may cause leakage, and may also cause a short circuit in the circuit, resulting in a fire; However, the plug can be used normally after drying.

Note that the use of power strips, like this kind of sockets is best used in the bedroom or living room, dry place away from the liquid. If certain isolation measures cannot be avoided for the socket strip, otherwise once the socket comes into contact with water, it will either be short-circuited or broken. Pay attention to check the dirt inside the socket and do not touch it when your hands are wet.

The problem is not big, use the sun to dry, or use an electric hair dryer to bake it, after 12 hours, wait for the socket to completely dry and the water evaporates on it, if you are not at ease, you can test it with a multimeter to see that the insulation resistance reaches 2 megaohms, you can rest assured that there is nothing to do.

If the socket is watery or wet, it is recommended to dry it (it can be dried with a hair dryer) before use.

It is best to disassemble it and wash it with pure water first, then wipe it with anhydrous alcohol, dry it and then install it before using it. Ordinary water contains impurities, if it is not treated and dried, it will run electric hemp hands as soon as it encounters a cloudy day and resurgence.

OK. It is best to remove the back fixing screws with a driver to open the back cover, wipe the moisture inside, and then use a hair dryer to dry the socket hole.

It is best to remove the back fixing screws with a screwdriver to open the back cover, wipe the moisture inside, and then use a hair dryer to dry the socket hole, and then install and reset it to use it normally.

You can continue to use it, but you can take it apart and get the water open or leave it in the sun for a few days to confirm that it is dry.

If there is water leakage, it cannot be used, but there is no problem with using it after drying. Of course, it is best to open the back cover of the mobile socket and ventilate it to dry.

The socket feels like it's leaking when water enters it, so of course you can't use it! If it is thoroughly dried and tested, it is completely ready to use!

It's not so evil, in general, there is no problem, but you must first disassemble the socket, dry it or bake it with a hair dryer, after a day, measure it with a multimeter, if the insulation resistance can reach more than 1m ohms, there is no problem at all, and the answer is just for reference.

You can't continue to use the socket because it is easy to leak electricity.

Solution: 1. Open the socket.

2. Use a hair dryer to blow on the junction box and socket.

3. Power on after blow-drying.

The socket was definitely not usable at the time, but it could be used if it was exposed to the sun for the second time. However, if the water has been ingested for a long time and has been oxidized, it is best not to use it to avoid danger.

Do not use the socket after the water is in, it may cause an electric shock accident, put it for a while, and it can be used after the water is dry.

It's better not to use it! After the power is off, remove the panel, dry it with a hair dryer, or replace it with a new one, which is safer. Otherwise, there is a risk of electric shock.

It is best to disassemble the socket and wipe it clean and then dry it before you can continue to use it, and you must clean it up after the power is off.

Water ingress into the socket will generally cause a trip, which will disconnect the power supply. Dry the water (e.g. with a hair dryer) and continue to use it when it is completely dry. FYI.

If the socket is flooded, it feels like there is a leakage, so it is recommended to use a hair dryer to dry it or use it after the wind is dry.

It is better to disassemble and dispose of it, and if it is cold and dry, it can be used if there is no problem inside.

If there is water, it is best not to wipe it clean and dry, it can be used in the future and will not leak.

Of course, the socket cannot be used if it is flooded, it will be electrocuted or short-circuited, and it is best to disassemble it and dry it with a hair dryer before use.

It can still be used after drying, and when there is water at present, the power is still cut off first, and then the power is used after drying.

If the socket is filled with water, if it is clean water, control the water inside, dry it, and use it again.

To speed up drying, you can dry it in the sun, or blow it on with a hair dryer.

You can continue to use it, but first it must be dried.

Because water conducts electricity (generally water contains impurities). So there will be leakage. It is forbidden to plug in the live plug with wet hands in the safety of electricity.

If the water inlet into the socket is relatively small, it will generally dry out after a period of time.

However, if there is more water in the socket, there is no way to dry it by itself, in this case, the water inside should be discharged in time, you can use a hair dryer to dry it or use a cotton swab to absorb the water inside, to ensure that there is no water in the socket before it can be used normally. If it is particularly severe, open the panel to clean it, and there must be no moisture residue, and then reinstall it.

When using various sockets, be sure to place them in a dry place that does not come into contact with liquids. Pay attention to check the dirt inside the socket, and do not touch the socket when your hands are wet.

How to choose a socket:

1. From the appearance, whether the style and grade of the socket switch are consistent with the overall style of the interior. The white switch is more versatile, and the overall tone of the interior decoration is basically a light color, so you should not choose some dark socket switches such as black and brown.

2. It is best to choose a well-known brand for socket switches, because the bad of socket switches is related to whether electrical appliances can be used normally, and there are many small manufacturers on the market that produce socket switches that are very unreliable and will not take long to break.

3. The socket switch uses bulletproof glue of high-grade materials, and its fireproof, moisture-proof, and impact-proof functions will be relatively high and the surface is very smooth. If the surface is not very smooth, and the search is thin and brittle to the touch, then the various properties of this product are not trustworthy.

In the case of water ingress into the socket, the power supply connected to the socket should be turned off as soon as possible to avoid leakage. Water ingress into the socket will cause the circuit board of the socket to burn out, and it can generally be used after the water enters the socket to dry

1. In the case of small water intake, it is possible to insert the drain.

Use it after drying, but be aware that all the water must be dried when using.

2. Before use, the inlet water of the plug must be dried, and it can be dried with a paper towel or dry cloth, and then placed in a ventilated place to dry it automatically.

3. If there is still water in the socket when it is used, it is likely to cause short circuit or leakage of the socket, so it is necessary to remove the water before use.

Water ingress into the socket can easily cause electrical appliances to burn out.

There are many reasons for the short circuit of the socket, the common ones are water leakage into the socket, the use of aluminum wire as the wiring of the socket, the wrong connection of the socket wire, and the overload operation of the socket. The consequences of the socket short circuit caused by different reasons will be different. The short circuit caused by water ingress into the socket and overloaded operation of the socket mentioned above can easily cause the appliance to burn out.

When installing and using the socket, you should try to operate in the correct way and method, and pay attention to various details of use to avoid short circuit in the socket. If the socket is short-circuited, cut off the power supply at home, then find the cause of the short-circuit, and finally use appropriate methods to solve it according to the cause.