What should I do if Blancpain does not maintain the hands of the watch or what should I do if the Bl

Hello, it may be a lack of motivation. If you need to wind a mechanical watch by hand.

Generally, the normal winding takes 30 times, and it is basically full, (provided that you want to be full) The winding watch on your hand actually doesn't matter, as long as you keep it up until you can't turn it, the mainspring is full.

For automatic watches, because most automatic watches can be wound by hand, especially when worn for the first time or after stopping, you need to use your hands to open the wind. Therefore, it is recommended that the number of windings of the automatic watch should be more than less, and you may wish to put a few more, such as up to 40 times, and it will basically guarantee that it can be full.

Room 2513, 25th Floor, Diwang Building (Shun Hing Plaza), No. 5002 Shennan East Road, Luohu District, Shenzhen, Guangdong Province] will answer for you.

Since the hands are installed in layers, and the top tube is connected to the second hand, the second hand is usually lost. If the hands of the watch are dropped, the crown should be pulled out in time to stop moving to prevent the hands from scratching the watch, dial or breaking themselves. After pulling out the crown, please repair it in time to prevent the watch from dusting.

In general, if there is no damage to the inside of the watch, it is easier to repair, but if the wheel tube is deformed, broken or the parts are worn, the repair will be slightly more difficult. Pay attention to the selection of a regular mechanism to prevent scratching the dial and reducing the waterproof performance of the watch. When installing the watch hands, a thin film is placed on the dial to protect the dial.

After installing the watch hands, a comprehensive waterproof test is required, and the waterproof ring needs to be replaced again if it is aging.

If there is a problem with the watch, it is recommended to go to the regular after-sales service for maintenance, not only the technician is more professional, the instrument is also more precise, and the **transparent is not messy**. There is a very good after-sales service near Wanling Hui in Tianhe District, so I will go to see it when I have time. My personal advice is to pass as soon as possible, otherwise the longer the time, the greater the problem with the watch, and the greater the economic loss.

The main thing is that it is still more troublesome, and the repair time will become longer.

Reasons why the watch is not running accurately:

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the automatic mechanical watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a continuous phenomenon of speed and slowness, if there is still a suggestion to send it to the after-sales center for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy, and send the watch to the after-sales center to check the battery or replace the battery.

3. Having been beaten or impacted. The watch is very tight, if it is hit or fallen, it may cause loose damage to the internal parts, and it may also cause time problems, it is recommended to go to the after-sales center for testing.

4. Maintenance is required. The lack of oil in the movement or the wear and aging of the internal parts may cause time problems, which need to be serviced and sent to the after-sales center for maintenance services.

5. The watch is magnetized: If the hairspring of the watch is magnetized, the watch will not be accurate.

The influence of the wearer's usage habits may cause an increase in the time error. Sending it to the after-sales center for inspection and adjustment can restore the watch to the normal error range.

Hello, glad to answer for you!

Reasons why the watch is not running accurately:

1. Insufficient power reserve. If the amount of exercise is small, it may also cause a lack of power reserve, so you can replenish the power by winding it manually, and then observe whether it continues to be fast or slow.

2. The watch has been hit or impacted, which may cause loose damage to the internal parts and may also cause the problem of running time.

3. The lack of oil in the movement or the wear and aging of the internal parts may cause the problem of running time, which needs to be maintained.

Do maintenance when the watch is fixed.

Every 1 to 4 years, corresponding maintenance should be done, waterproof components should be replaced, the function of the movement and the power consumption of the movement should be checked, the movement should be cleaned and the appearance should be maintained. This kind of maintenance will effectively extend the service life of your mechanical watch.

Do not place the watch on the stereo or TV to prevent magnetization.

Do not leave the watch in a closet with mothballs to prevent the oil from deteriorating.

Never touch the watch with corrosive substances, especially acids, which can corrode the case.

It is not difficult to take care of your watch on a daily basis, as long as you can do these things on a regular basis, you can trust that your watch can always be kept in the best working condition. When it is worn on your wrist, it will definitely highlight your charm and temperament!

Attention should be paid to the daily wear of the watch:

1) When wearing a watch, the sweat on the hands is corrosive to the case, the all-steel case is better corrosion resistance because it is nickel-chromium alloy, and the semi-steel case is copper, which is in contact with sweat for a long time, and is easy to corrode, so you should often wipe off the sweat with a soft cloth or put on a plastic watch holder to prevent it from being eroded by sweat.

2) Do not open the back cover of the watch at will, so as not to enter the movement and affect the normal operation of the watch.

3) Do not put the watch in a closet with mothballs to avoid the deterioration of the watch oil.

4) Do not put the watch on the radio or TV to avoid magnetization.

5) Watches that are not worn for a long time should be wound regularly once a month so that the parts will not be in a stationary state for a long time, so as to ensure the operation performance of the watch machine.

Method 1: Use granular silicone and put the watch into a closed container with the water accumulation, and after a few hours, take out the watch and the water will disappear. This method does not damage the timekeeping and components of the watch;

Method 2: Lamp baking method: Wrap the watch in water with a paper towel, put it at about 15 cm near a 40-watt light bulb, and bake for about 30 minutes. Never roast over fire;

Method 3: Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the moisture can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

After the above is done, it is best to go to a professional repair shop to do a comprehensive maintenance, the key attention is: do not try to shake the water, so as not to throw the parts off, and the bulb must not be too close when baking.