What to do if Franck Muller repairs the watch hands incorrectly

It may be a lack of power. If you need to wind a mechanical watch by hand.

Generally, the normal winding takes 30 times, and it is basically full, (provided that you want to be full) The winding watch on your hand actually doesn't matter, as long as you keep it up until you can't turn it, the mainspring is full.

For automatic watches, because most automatic watches can be wound by hand, especially when worn for the first time or after stopping, you need to start the winding with your hand first. (It is recommended that you do not rely on the rotor to wind the full string at the beginning) everyone also knows that because the automatic watch is "not up to the string", it is recommended that the number of winding times of the automatic watch should be more than less, and you may wish to put a few more, such as up to 40 times, it is basically guaranteed to be full.

1. There are many reasons why the watch is inaccurate, and most of the phenomena that occur in the watch are caused by the magnetism of the watch or the fact that the watch has not been cleaned for a long time.

2. If your watch has not been cleaned for a long time, it will also cause the watch to run inaccurately or not time, because the dry oil sludge of the movement will increase the friction of the parts, which will cause the watch to stop. Therefore, it is recommended that you must do a good job in the washing and maintenance of the watch movement.

3. The inaccuracy of the watch may also be caused by bumps, which can easily cause Audemars Piguet watch parts to fall off or be damaged, so go to a professional watch repair shop to replace and repair the relevant parts.

Fourth, if the watch is magnetized and the watch is inaccurate, you can find a non-magnetized iron ring by yourself, and then walk the watch through the iron ring a few times to demagnetize. If this method does not demagnetize, the watch can only be sent to a professional watch repair shop to be treated with a degaussing machine.

The easiest way is to fix it, but it could be the following scenario. 1. Clamp 2. The second hand is loose, and you can shake it a few times. If not, it would have to be sent for repair.

You want to make sure that you don't only have the minute hand and don't go. The rest is normal. If the rest is normal, it is most likely stuck on the wind.

The watch is a part of our life, the second hand of the watch does not go, don't blame him, let him rest, think about it from his point of view, if it is you, what will you do, when you are tired, just think about the watch, he is very tired, and he can't stop. You, not the most tired, but, as a tool to control time, can't cut corners and leave a little time for him to rest.

The Franck Muller Maintenance Center is located in Room 2606, Block B, China Resources Building, The Mixc, No. 1366 Qianjiang Road, Jianggan District, Hangzhou.

Whether the power reserve is sufficient.

If it is a mechanical watch that is automatically wound, the lack of exercise will cause insufficient power reserve, which will affect the accuracy of the time, and the power can generally be supplemented by manual winding, and then observe whether there will be a situation of fast or slow walking.

Affected by magnetism. If the hairspring of the watch is magnetized, it will seriously affect the timekeeping and other work of the watch. So how do you detect if your watch is magnetic?

The easiest way to judge is to use a sensitive point compass to lay flat, and then the watch is quickly repeated over the top of the compass at close range, such an action also needs to change the watch in a few more directions, in the repetition, as long as the needle of the compass moves, it means that the watch has been magnetized.

Wear and tear of parts. Problems such as wear and tear of the internal parts of the watch or lack of oil in the movement can cause problems such as running time, and in this case, it is necessary to send it to a repair center for maintenance service.

Impacted. A square inch size watch is wrapped with dozens or hundreds of precision parts, if it is hit or collided, it may cause internal loosening damage and cause time problems.

Temperature effects. The change of temperature difference will also affect the time of the watch, and the normal temperature range of the watch is between -5 and 35. If it is a temperature problem, as long as it returns to normal temperature, the accuracy of the watch will also be restored.

Of course, in addition to the above common situations, some of the wearer's own wearing habits may also affect the problem of abnormal walking. Therefore, maintaining a good wearing habit will not only extend the life of your beloved watch, but also bring accurate timekeeping.

A fully automatic watch is wound entirely by the swing of the arm.

Therefore, if the watch is left for too long or the amount of arm activity does not meet the requirements of the watch winding every day, the watch will cause the mainspring to be winding and the potential energy is insufficient, which will cause the watch to be unstable or stop when it is not worn at night.

If this happens, we can manually do an arc movement before the watch is placed. Or use the manual winding function to wind the watch. This keeps the watch with enough kinetic energy storage to keep it running until the next day.

There are two situations in which the watch is not allowed.

If it's just a little fast, for example, it's only more than ten or twenty seconds a day, then the gossamer circle is a little shorter, and this situation is okay.

If you know a little bit about the watch, you can adjust it yourself, if you don't understand, you have to find a watch repairer.

If there is a problem with the watch, I recommend going directly to the watch after-sales center. After-sales is not only more professional technicians, but also the instruments are imported, more precise, and **also very transparent, will not be messy**. When not to go to a regular after-sales center.

Otherwise, if you are trapped, you can only blame yourself.

Hello, glad to answer for you!

Reasons for inaccurate time: insufficient kinetic energy reserve of the watch, insufficient battery of the watch, the watch has been hit or hit by an external source, the watch has not been maintained for a long time, and the watch is affected by magnetic fields.

Solution: It is necessary to go to the after-sales center for testing and maintenance.

If you have any questions, please call** Please feel free to call.

If you find that your watch is going faster or slower, you can find a compass to diagnose whether the watch is magnetized. Place the compass flat on the table, hold the watch at close range and quickly shake it back and forth above the compass, and try the watch in a few directions a few more times, as long as the pointer moves, especially if the deflection is very strong, you can judge that the watch is magnetized. The watch is magnetized and it is best to take it to this repair center for demagnetization.

Usually take care of the watch, do not let the watch come into contact with items with strong magnetic fields, and it is best to keep a distance of more than one meter. Do not leave your watch next to TV, computer, radio, mobile phone, mahjong table, refrigerator, washing machine, speaker, car door, or leather bag magnetic buckle.

Another reason is that summer is coming, and the hot weather will go faster than the cold weather. Yes, there are two laws of physics here. One is the thermal expansion and contraction, the weather is hot, the hairspring will be a little elongated, this everyone wants to get, therefore, the lengthened hairspring, the swing will also increase, and the watch will slow down; On the contrary, when the weather is cold, the watch will go faster.

The watch is not allowed to be processed:

1.Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to be fast or slow.

2.Insufficient battery: If the quartz watch suddenly finds that it is slowing, it is likely that the battery is insufficient, and you can send the watch to a special repair point to check the battery level.

3.Having been hit or impacted: The watch is very tight, and if it is hit or hit, it may cause loose damage to the internal parts, or it may cause time problems. This is to be dealt with in a timely manner.

4.Need for maintenance: The lack of oil or the wear and aging of the internal parts of the movement may cause time problems, which need to be serviced and sent to a designated repair point for maintenance services.

5.In addition to the above common situations, the watch is affected by some ambient temperatures: if the balance spring of the watch is magnetized, the watch will not be accurate.

The watch is not allowed to go to Hangzhou Franck Muller for repair service? If my cousin is indisputable, he will definitely go and fix it.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

It's still needed, if you don't know how to adjust it yourself.

Check to see if your watch is magnetized.

Reason 1: The hairspring is stretched and curled in the work, at the moment of stretching, it happens to encounter the external impact force, and the hairspring acts with external force, and the hairspring is quickly stuck on the needle clamp together with the outer wheel of the hairspring, or stuck on the outer pile pin of the movable outer pile ring.

Reason 2: After the hairspring is subjected to external impact vibration, it may cause the fast and slow needle to rotate and rotate, and the action length changes.

Reason 3: Newly purchased watches or watches that have been cleaned and oiled for a short time have oil leakage due to over-lubrication or incorrect injection, and the hairspring is partially fixed and the working length is shortened.

Reason 4: When working or going in and out of a large magnetic field, the balance spring and the like are magnetized and overlapped by each other after a long period of daily accumulation, and as a result, the watch stops completely.

Mechanical watches run fast, basically caused by the above four reasons, when the watch encounters a fast situation, do not worry, go to a professional watch maintenance agency to check.

The first reason: the lack of power of the watch.

Mechanical watch, it is by the wind, elastic potential energy into kinetic energy, mechanical watch compared to quartz watch is not so punctual, mechanical watch movement is more complex, parts part, friction and loss will be more, kinetic energy loss is fast, in the case of insufficient elasticity of the spring plus the loss of parts, the error will be obvious. So when the watch is not on time, first check whether your watch has enough power.

The second reason: whether the watch is magnetic.

If your watch is disturbed by magnetism and the time is not accurate, you can go to a watch repair shop for help. Because there is a step to demagnetize the watch, in fact, there are many magnetic fields around us, such as electrical appliances, electromagnetism, sometimes when we come home, we may put the watch on the TV, stereo, etc.

The third reason: the watch movement runs out of oil and needs to be maintained.

The friction between the movement parts of the watch will lose our power, and if the mechanical parts are aging, it will bring a lot of friction, and the watch needs to be brought to the watch store for maintenance.

The fourth reason: temperature and other external factors. The daily collision of the watch such as thermal expansion and cold contraction also has an impact on the time of the watch, you can go to the watch repair and maintenance shop, where there is a professional watch master, otherwise your own rash operation may make the problem more serious.

The watch does not go for reasons and how to deal with itLack of power: Some friends do not wear the watch every day, or wear it for a short time every day, which leads to the lack of power of the automatic watch and the watch does not go. Automatic watches wind the watch by moving the arm, and if you don't exercise enough or don't wear it, the watch won't go.

This principle is the case with various brands of automatic watches.

The solution: wear more, exercise more, and remember to wind it when you don't wear it.

Dead battery: The most common reason why a quartz watch won't go is when the battery is dead. This is the first consideration of quartz watch abrupt stop.

The solution: Replace the battery with a new one.

Damaged internal parts: Damaged quartz oscillator or faulty circuit board.

The solution: replace the quartz oscillator, if it doesn't work, you need to replace the circuit board.

The watch has not been maintained for a long time: too much dirt inside the watch, jamming the gears, or making the battery in poor contact will cause the quartz watch to not go.

Hello, if it's a newly bought Franck Muller watch, suddenly it's out of time. Because there is a possibility that the cause is external interference. You should take it to repair it in time to prevent rust.

Insufficient kinetic energy: A fully automatic mechanical watch that operates by the action of the automatic winding mechanism that can tighten the mainspring when the rotor rotates in any direction. Only when the watch is worn on the hand, the rotor rotates to generate energy as the arm moves.

Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the mainspring. So.

The common problem when the watch does not go is the lack of kinetic energy, or it may be because the watch needs to be repaired and maintained, in the case that we do not know the reason, we should take the watch to the regular after-sales service for the technician to test. Before my Franck Muller watch was out of time, I thought it was caused by insufficient kinetic energy, but I got the after-sales inspection of the counter and found that it was necessary to maintain, and it was repaired and maintained in Room 602, Block W3, Oriental Plaza, Dongcheng District, Beijing, the technician was very responsible and professional, my problem was solved, and the technician also told me to let me do maintenance regularly, so as to avoid the phenomenon of stop-and-go.