How to connect to the Internet with a broadband cable to a computer road gamer

The broadband network cable is connected to the WAN port of the router, and the PPPoE is required to dial up, and the static IP is that Telecom or Unicom gives you a fixed IP, or that there is a switch in your corridor to choose to obtain it dynamically.

Here's how to set up your router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

5. According to the setting wizard step by step setting, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

6. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

First of all, connect the incoming cable when the broadband is installed to the LAN port (cat), and the other end is connected to the WAN port of the router.

Then call your browser, enter and enter your account password. It's all admin

After entering, go to the interface of Swift Network and click on the setup wizard on the left.

After clicking, in the interface that comes out, you can directly click Next.

Click Next Later. The default in the interface is to let the router choose the appropriate way to surf the Internet, and there is no need to change it directly to the next step.

Then there will be an account password to enter, that is, your account and password that you will be told when you install broadband, enter it directly and click Next.

Then come out of the interface and choose the one you need. Set the name and password of the router, and click Next after you have set it.

Then after clicking, an interface will come out for you to check the parameters you set, and click the save button after confirming that they are correct.

After saving, a setting status comes out, and you can check the current situation of your own settings, all of which are genuine, and at this point, the setting of the wireless router is completed.

Here's how to connect your router to your computer to surf the Internet The steps are as follows:

1: After entering the computer settings, we need to select the option to click on "Network & Internet".

2: Next, we need to click to open to enter the "Network and Sharing Center" function.

3: Then click on the "Network and Sharing Center" feature to enter the "Ethernet" option.

4: Then we need to select and click into the "Properties" button.

5: Then we need to go ahead and select click into the "IPv4" option and click on the "Properties" option.

6: Finally, we just need to click on and select "Automatically get IP address" to connect the router for wired Internet access.

The steps are as follows: 1. Plug the network cable from the cat into the WAN interface of the router;

If you don't use a cat for your home broadband, you need to plug the broadband network cable into the WAN interface of the router.

2. Connect your computer to the free interface in the router lan1 2 3 4 with a network cable, and the complete connection diagram is as follows.

Hello dear and happy to answer for you. How to connect a router with broadband You can follow the steps below: first find a network cable that is long enough, connect one end to the computer, and connect the other end to any LAN port of the router (usually the router will have four LAN ports, and these four LAN ports are universal), and the connection between the router and the computer is completed, it is very simple.

Supplement: If you connect like this, you can't use the Internet when the router is set up, because the router is not connected to the external network. The line that comes out of the home network cable or cat (fiber optic cat or **cat) is the network cable connected to the computer before the router is connected to the WAN port of the router, so the overall connection "I hope the answer of the answer can help you, I wish you a happy life [than the heart] [than the heart] [than the heart] [than the heart].