The front headrest can t be removed, how to change the seat cover, the car is a Fiat Palio. Thank yo

The correct way to disassemble the front headrest of Nanqi "Palio (Sienna weekend wind)".

The design of this front headrest is different from that of other models, and the locking position is not on the headrest slide, but on the inside of the seat. To completely remove the headrest, you need to take the following two steps:

1.Loosen the seat backliner:

Put your hand on the back liner of the seat and touch it all the way down, and when you reach the bottom, touch your finger forward, and you will feel the buckle, and then loosen the buckle.

2.Pull the headrest lock:

When the backliner buckle is loosened, the backliner of the seat will not be tightly taut on the seat, and you can reach through the gap between the backliner and the seat. Stretch it all the way up, and then your hand will touch the pin-like spring made of wire, one on each side of the two connecting rods; Pull both of these springs to the side of the headrest connecting rod (or a transverse lever similar to the front and rear adjustment levers of the front seat). Pull this lever) The lock of the headrest is opened, and it is easy to remove the headrest.

Additional Notes:1The seat liner refers to the part of the back of the seat.

2.When removing the backliner buckle, it's a good idea to adjust the seat to tilt back so that it's easier to pull the backliner buckle.

3.Some seats have tighter backliners, so you need to use tools to loosen the backliner buckles.

4.If you're not sure which is the backliner buckle, you can put your hand on the bottom of the backliner, hold it, and shake it from side to side, indicating you're in the right place.

5.Once the backliner buckle is open, adjust the chair to lean forward so that your hand can reach in and pull off the headrest link. That's it.

I couldn't take the front pillows, and my seat cover was cut a little bit to fit in.

I couldn't take it off, so I flattened the headrest and pressed it in when I loaded the seat cover.

If you can't remove it, you can try squishing it

In order to protect the cervical spine, the seat safety headrest should be adjusted to be level with the head, so that the cervical spine can be effectively protected when subjected to a large impact. If you only adjust it to the same height as the cervical vertebrae, imagine that when you receive a strong impact, the head may be folded backwards, which can easily cause cervical spine injury.

Are the front side airbags on the side of the front seats? Can the side airbags be opened with the seat cover installed? I'm about to dig a big hole in the side of the seat cover, and I'm about to install a seat cover, so I'm a little worried.

For more information about the carnival, please see Ekcar Cars.

There is a plastic ring where the headrest is connected to the car seat, and there is a place where you can press down to remove the headrest from the seat as a whole.

Car headrests are a kind of driving comfort configuration and safety protection equipment.

Importance. Even if the speed of the vehicle is only 10 km h, in the event of a collision, the acceleration and deceleration forces of the vehicle are all squeezed on the fragile neck of the person, and if the car headrest is not protected, the neck of the driver and occupants in the car is easily injured.

According to the statistics of the relevant departments, neck sprains are one of the most common injuries in car accidents. The data shows that in 26% of rear-end collisions, the head or neck of the driver and occupants will be injured, and in the same rear-end collision accidents, the correct use of car headrests is 40% less likely than that of incorrect use of car headrests, and the probability of neck injury is 24% lower than that of drivers and passengers who use inferior headrests.

In the event of a traffic accident, the huge impact force generated by the collision is all squeezed on the fragile neck, so that the spine of the driver and passenger is likely to be injured, and in severe cases, it can even lead to nervous system problems leading to paralysis and even life-threatening.

With the presence of car headrests, it can effectively cushion the huge instantaneous impact force in the event of an accident, thereby protecting the fragile neck bone and reducing the chance of neck injury.

Remove the car seat headrest.

Tools Raw Materials:

Two screwdrivers with a slotted taper.

Method Steps::

1. Prepare the car headrest tool for disassembly.

First of all, we need to prepare the tools for removing the headrests of the car. A big screwdriver and a small one, then we will start the wonderful disassembly process.

2. Adjust the car headrest button.

As shown in the image, we first adjust the buttons of the car's headrests. It is necessary to know how to adjust the height. Hold the plastic button underneath the headrest support bar. This plastic button is equivalent to a small switch. It can use its other hand to move the support bar of the car's headrest up and down.

3. Disassemble the car headrest.

As shown in the figure, we need to press the adjustment button with one hand, hold the car headrest with the other hand, and then lift it up so that the support rod of the car headrest is separated from the seat and take the headrest down. Pull.

4. Observe the adjustment button of the headrest.

As you can see, it is more difficult to remove the car headrest adjustment button. This adjustment button is inserted into the rear of the car. Santana's backrest is better. It's a fabric. It is better to disassemble. If leather is required, special attention is required.

5. Disassemble the headrest adjustment button.

The removal method of this adjustment button, as shown in the figure, we need to press the cloth around the adjustment button slightly down, exposing a part of the adjustment button, and then take out the large screwdriver, the large screwdriver When you reach the underside of the adjustment button, you will touch a protruding plastic buckle, smash it inside with a screwdriver, and pick up the adjustment button with the other hand.

6. The adjustment button of the car headrest is removed.

As you can see, we can lift the adjustment button and separate the button from the rear of the car. You can see that the adjustment button is too long. After disassembly, the place where the adjustment button is installed in the rear of the car is such a deep hole.

7. The car headrest assembly is disassembled.

In this way, the entire car headrest removal process is over. During the disassembly process, you have to be careful and avoid breaking something. As long as you are slow and careful, you can do well.

1.There is a plastic button under one side of the two support rods of the headrest, which can be pressed to move up and down and adjust the position of the headrest.

2.The headrest can be removed by pulling it out completely upwards while pressing it.

3.To install, simply insert the headrest support rod directly to snap into the highest gear of the headrest, and adjust the headrest position by pressing the button again.

Why can't the headrests of the front seats be removed? Can only go up and down? So how do you press the seat cover? There is a circlip at the joint that connects the headrest to the backrest, and you can take it off with a screwdriver.

In addition, after the backrest is lowered, there is a plastic paddle at the lower end of the two vertical east-east (it seems to be introduced in the manual), and then it is pulled out. For more information about the Audi A6L, please visit Ekcar Automotive.

There is a button on the side of the pole when you pull it out, and it comes out when you press it, and it is really not possible to find a four-s store without charge. Pull it out directly, he is very tight in the last piece, and it comes out with a little strength.

Car Headrest circlip How to disassemble which small piece to pull up If you are afraid of getting lost when you drive out, find me: Friends who often drive out often encounter getting lost, or taking the wrong road, how to avoid taking the wrong road.

You can go to the car decoration shop and ask a professional to dismantle it, ask a professional to dismantle it, and then go to the car decoration shop and ask a professional to dismantle it.

The connection between the headrest and the seat is two iron columns, one with a groove, in the base with a groove (that is, on the backrest), there is a card loss on this base, which can be pressed, after the card loss is pressed, and then pull the headrest upwards to take it down.

The old Santana, the headrest has two metal tube bases, and there are circlips in those two positions, and you can pull out the disc cover with a flathead screwdriver.

How can the 2017 Volkswagen Magotan front seat pillow be disassembled.

3. Next, put on the headgear of the front seat cushion of the car, as shown in the figure below.

4. Take out the chuck of the front seat cushion of the car below, as shown in the figure below.

6. Plug the front seat cushion chuck into the gap below, as shown in the figure below.

7. It is necessary to pay attention to the chuck of the front seat cushion of the car into the seat cushion and get stuck, as shown in the figure below.

9. Then fasten the elastic band of the apron of the front seat cushion of the car, as shown in the figure below.

11. Finally, the front seat cushion of the car is installed, as shown in the figure below.

Don't go through the hassle, insert that little square vertically into the gap between the cushion and the backrest, and pull it from behind if you can't get it in! You should be able to do it anywhere else!

The front seats of the car are generally fixed with four screws separately below, and only by removing them can the problem be solved.