If you want to clean a natural gas water heater, how should you clean it?

The appearance of gas water heaters needs to be cleaned and wiped frequently, most of the water heaters are installed in kitchens, bathrooms, balconies, etc., which are easy to contact with dust and smoke, and dust and soot are directly attached to the water heater shell for a long time, which is difficult to clean after forming stubborn dirt, affecting the use of internal parts, so it needs to be treated at intervals. The method of cleaning the enclosure is relatively simple. Regular weekly wipes with a rag will do.

If there is oil smoke, you can apply a little detergent to the rag to quickly remove the oil stain on it.

To clean the inside of the natural gas water heater, the shell must be decomposed to be cleaned, and the carbon slag at the burner site should be cleaned with a special carbon remover, first put the carbon remover into the cleaning solution, and then soak it for a period of time until the charcoal becomes soft, and then wipe it with a brush or rag. Rinse with hot water after wiping. Do not use it after washing, do not wash, the internal structure of the water heater is complex, it is recommended to contact the brand for professional after-sales service guarantee.

After preparing the tools and materials to be used, unplug the power of the water heater, close the gas valve, close the water inlet valve, confirm that the water heater is in a state of water cut-off, power-off, and gas cut-off, and do not start it when cleaning. Spray hot water or turn on the faucet to drain the water. Open the drain valve at the water inlet so that the water inside the water heater drains completely.

Note that some water heater drain valves may be at the drain outlet, some water inlets are filters, and some have safety valves, as long as they are opened, the air can come in and drain all the water in the water heater.

After the water in the water heater is drained, we now need to inject the detergent into the water heater. There are various methods, usually from the drain valve at the water inlet. Injection methods with a special door design can be used, small pumps can be connected, and the simplest large syringes can also be used.

The specific detergent concentration should be diluted in advance according to the instructions of the detergent you bought, in powder form. When injecting the cleaning agent, it is recommended that the warm water hose is also injected into the cleaning agent until the entire hot water system and the inside of the water heater are filled. Pay attention to the water heater here as well.

Generally speaking, the installation is relatively high, and the position of our faucets, shower water, and no water heater is very high, and the detergent that goes in will flow out, so we have to take appropriate measures to prevent the detergent from leaking and fill the water heater to the brim. There are many specific methods, such as raising the water pipe a little bit and closing the valve in time. We talk too much.

The detergent cannot be drained immediately after the infusion is completed. The detergent should be dissolved in reaction with water. The specific soaking time is carried out according to the concentration we adopt and the requirements of its instructions.

It should also be noted here that the cleaning agent is generally acidic when it is water, and when it reacts with alkaline water, the metal also has a certain corrosive effect. The inside of our water heaters is usually a heat exchanger made of copper, which also produces a certain degree of corrosion, so the immersion time and the concentration of cleaning agent must prevent corrosion of the water heater according to the requirements.

You should find a professional cleaner to clean it, and never clean it yourself, otherwise it is likely to damage the natural gas water heater.

1. Prepare a hot water pipeline descaler and descaler.

2. Close the water inlet valve again and disassemble the hot water pipe nut on the hot water inlet.

3. Connect the nut of the pipeline descaler to the nut of the hot water pipe.

4. Then, turn on the hot water faucet to vent the pressure and keep it on.

5. Inject descaling agent into the hot water pipeline to soak.

Generally, there can be a professional cleaning machine, which can help remove some limescale inside, or you can add some white vinegar to it yourself before rinsing.

You can use a damp cloth to directly clean the dirt in the shell and filter, or you can directly check whether there is scale in the water tank and clean it up in time.

1. Internal cleaning 1. Turn off the water heater and unplug the power supply. 2. Close the water inlet valve and unscrew the water heater inlet pipe. 3. Add the water heater descaler to the adder and connect it with the water inlet pipe and water inlet (press 1:

The ratio of 3 is to dilute the concentrated hydrochloric acid into a low-concentration hydrochloric acid solution with Huaidong water). 4. Plug in the power supply of the water heater, open the water inlet valve, raise the water temperature to more than 50°C, and turn on the water heater. 5. Open the hot water faucet, let the water flow drive the descaler into the water heater, close the water heater valve and remove the adder, and connect the water inlet to the key normally (you can add an appropriate amount of cleaning agent many times).

6. Let stand for more than 30 minutes, open the water inlet valve, and turn on the hot water faucet to empty the sewage. 2. External cleaning should often be wiped with a wet towel, and it should be noted that you cannot use a series of cleaning agents such as acidic and alkaline to wipe the water heater.

1. Exterior cleaning.

Most of the water heaters are installed in the kitchen, bathroom, balcony, etc., which are easy to come into contact with dust and fumes, and after a long time, dust and fumes will directly adhere to the water heater shell, which is difficult to clean up after forming stubborn dirt, and will also affect the use of internal components, so it needs to be dealt with every once in a while. The method of cleaning the shell is relatively simple, wipe it with a rag regularly every week, if there is oil smoke, you need to apply a little dish soap on the rag, so that you can quickly remove the oil stains on it.

2. Internal cleaning.

Natural gas water heater to clean the inside of the shell needs to be disassembled to clean it, the burner part of the carbon slag needs to use a special carbon remover to clean, you can first add the carbon remover to the cleaning solution, and then soak for a period of time, until the carbon deposition is softened, and then use a brush or rag to wipe, after wiping, you also need to use hot water to rinse it, after rinsing, do not use it first, you can use an electric fan to dry it, or install it after natural drying. The internal structure of the water heater is complex, so it is recommended to contact the brand for professional after-sales maintenance.

1.Clean the water heater shell: Wipe the case with clean water, which can be wiped with dish soap to avoid dirt accumulation.

2.Clean the inside of the water heater: Clean the inside of the water heater with clean water, which can be cleaned with dish soap to avoid dirt accumulation.

3.Clean the water heater electrodes: Wipe the water heater electrodes with a damp cloth to avoid dirt accumulation.

4.Clean the water heater pipes: Clean the water heater pipes with clean water, which can be cleaned with dish soap to avoid the accumulation of dirt shed leakage.

5.Clean the water heater exhaust port: Wipe the water heater exhaust port with a damp cloth to avoid dirt accumulation.

1. If it is just a simple light cleaning, then the user can clean it up by himself. Unplug and place the plug before cleaning to avoid water during the cleaning process. Then rinse with a simple cleaning tool.

2. If the gas water heater is cleaned deeply and professionally, then you can find a special household appliance cleaning master to deal with it. Turn off the power before cleaning; During the cleaning process, the dismantled parts are stored in a fixed position to avoid missing or missing; It is then cleaned using specialized instruments and a high-pressure water gun; Wait until the water is dry and then install it back and you're done.

Reasons for this:

1. The reason why the gas water heater will be blocked may be that it has been used for a long time and has never been cleaned, and there is too much dirt accumulated inside it, and it is adsorbed on its inner wall or covered with temperature sensing elements, etc.

2. It is also possible that the drainage pipe or air outlet is blocked. It may be because there is too much debris piled up near it, which affects the smooth airflow and also affects the efficiency of the exhaust.

3. It is also possible that the exhaust pipe is located outdoors and there is no shelter, so when the weather such as strong wind and rain is encountered, some foreign objects are prone to appear inside, which may lead to the blockage of the gas water heater.