Can the leakage of the exposed socket be sealed with adhesive tape?

Of course not, since the leakage indicates that there is a problem, either there is a leakage phenomenon in an electrical appliance at home, or there is a problem with the power supply line, or it is caused by the poor performance of the air switch itself.

First unplug all the electrical appliances at home, see if it still trips, if it still trips, it is best to find an electrician to replace the other empty open to see if it trips, if it still trips, it means that it is a problem with the line, and the line must be repaired to solve it. If you don't jump, it should be that this leak is not good, try another one, after turning it off, you touch this leak with the back of your hand, if it is hot, it will definitely leak bad.

The socket holes are sealed with transparent tape, which is safe and can only be used as a temporary measure. Because the transparent tape is insulating. However, transparent tape cannot be used as a substitute for electrical tape.

Precautions for use: When the adhesive tape is wound, do not affect the normal operation of other jacks, and do not splash water. Do not touch with sharp objects.

1.Check to see if there is a reset button on the switch, press it first and then push.

2.Troubleshoot one by one.

Are there any people in the neighborhood who are being renovated? Go find a master plumber and ask him to bring a multimeter and check the sockets in your house one by one. This will help you figure out which socket the problem is – it may be that there is a problem with which socket in your home, such as the socket is broken, or the wiring of the socket is not tightened at that time, and it suddenly loosens and detaches, causing the neutral wire to "catch fire" with the spark.

In short, let the master electrician double-check. Don't do it blindly.

When decorating a new house, the electrical circuit in the home is the most important, because once there is a problem, there will be endless troubles. Therefore, when you decorate the circuit at home, you must avoid all kinds of problems, but there is a problem that must attract everyone's attention recently, that is, when we merge the circuit, we should not wrap it up with adhesive tape, because there is no qualified leakage protection.

In fact, there are a lot of practical electrician tools now, which will be more time-saving and labor-saving when you use them, and they are also safer. Because when wrapping adhesive tape, you will find that not only need to firmly fix the combined wires together, and then wrap them with adhesive tape, but there will still be the problem of falling off, so it is best to use professional tools.

In fact, the current electricians have also begun to update, they will use some very good parallelers, so that not only have a very good leakage protection device, but also do not have to worry about the wire will fall off after a period of time.

In addition to wiring safety, household appliances are essential, whether it is a household appliance or some electrical appliances that need to be charged, there are some potential safety hazards, we all know that the power supply is most afraid of touching water, once the socket or power cord touches the water, then it is easy to have fire and other accidents. And all kinds of wires are messy, which not only affects the appearance but also affects safety.

Now there are a lot of socket boxes, which do not take up much space, but they can make the living room and kitchen look much neater, and it will not affect the problem of wire stretching.

The safety of electricity at home can not be ignored, and the use of some practical and good things can keep your home clean and tidy, and the safety factor has also skyrocketed. Let's go home and try it.

If the exposed socket leaks, it can be temporarily sealed with electrical tape, and it is not recommended to use it for a long time. If possible, replace the socket with a new socket as soon as possible, safety first.

No. Sockets are often touched by people, especially surface-mounted sockets. It can only be used if it is replaced by a professional electrician.

Of course, you can't seal it with adhesive tape, because the mistake is so big, and it's ugly for you to seal it, so it's best to buy a new one and replace it with a good-looking and safe one.

In real life, many people will ask a question in the process of using electricity, that is, whether the leakage protection socket can replace the leakage protection switch.

Is it? In fact, when using electricity, we must pay attention to safety, the leakage protection switch is able to make it safer for everyone to use electricity, then, the following will give you the answer to the leakage protection socket can replace the leakage protection switch? Where should I pay attention to leakage protection?

1. Can the leakage protection socket replace the leakage protection switch?

Theoretically, yes, but the leakage protection plug belongs to the low or later set of leakage protection, and should be fixed on the socket for a long time, so as not to move it often. Because it's just an electric water heater.

A kind of double insurance.

For real indoor power protection, it is recommended that you install a regular leakage protector.

The solution is good.

Second, where should attention be paid to leakage protection?

1. The socket circuit should be in the distribution box.

If the wall-mounted air conditioner is a dedicated circuit power supply, because the socket of the wall-mounted air conditioner is often set relatively high (about 2m), RCD can be omitted, and the socket of the wall-mounted air conditioner is recommended to choose one with a switch.

2. The lighting circuit can not be set up with RCD, but during the decoration, some plumbers will supply power to the new socket from the lighting circuit in order to save trouble, which is absolutely undesirable! Some smaller units do not have a special toilet socket circuit, and the power supply of the bathroom bath bomb is drawn from the lighting circuit, at this time, it is good to install RCD for the lighting circuit. In short, follow one principle:

Circuits that may come into contact when live should be equipped with RCD.

3. The general home distribution box is like the picture above, the left is the main incoming switch (commonly known as the main switch), the narrow ones on the left are the circuit breakers without RCD, which are lighting, distribution boxes, lighting standby and hanging air conditioners, and the wide ones on the right are circuit breakers equipped with RCD, which are ordinary sockets, kitchen sockets, bathroom sockets and cabinet air conditioning sockets.

4. The only disadvantage of the circuit breaker with RCD is that it is twice as wide as the circuit breaker without RCD, the former is 36mm, and the latter is 18mm. However, compared to life safety, this disadvantage is almost negligible.

The above is all the content that I will introduce to you today, mainly to introduce to you is that the leakage protection socket can replace the leakage protection switch and where the leakage protection should be noted, I hope this article can help you, from the above, the leakage protection socket can theoretically replace the leakage protection switch, but it is good not to be like this often, to avoid unsafe electricity.

I once heard a master say that he is an old electrician with more than 20 years of experience, and generally installs open wires for homeowners, and there are many householders who ask for their own requirements. But according to what we have learned, many decoration companies are now laying lines that are concealed, so what is the difference? First of all, the master gave us an analysis of the advantages and disadvantages of concealed and surface-mounted clothing.

1. Aesthetics.

There is no doubt about this, concealed installation is more advantageous than surface installation in aesthetics, the installation of the line is buried, the outside can not be seen, it is difficult to affect the design and decoration of the home, of course, there is the difference between the switch and socket, the concealed switch socket is obviously more concise and refined than the surface installation does not appear abrupt.

2. Security.

In fact, there is no doubt that if the exposed wiring is damaged, people may be most directly injured. Moreover, the exposed wire is more susceptible to damage, wear, oppression, soaking, etc., which is a kind of damage to the wire, thus indirectly harming us.

3. Service life.

If you don't count the damage, the rate of natural aging is that the bright line is faster than the dark line. The line will change with the change of air and temperature, assuming that the concealed line has a service life of 10 years, and the surface-mounted line is about 7 years at most.

It may be that from the above comparisons, the concealed decoration is indeed much better than the exposed decoration, and the concealed decoration should be chosen, but since the existence of the exposed decoration, it proves that these points are not enough to convince the master. The master said that many construction workers only look at one point: the difficulty of construction.

I believe that you can see from the concealed installation method that the construction difficulty of concealed installation is obviously greater than that of surface-mounted installation. One of the most critical is "slotting", if you want to slot, you need to face three situations: the construction cost increases, the construction time is extended, and the technical requirements are more stringent.

The first two points are easy to understand, but when it comes to technical requirements, this point is also extremely important, such as slot depth, wiring direction, and openings. If you are unlucky and encounter a master who is not skilled enough to destroy the building, it will be very bad.

Many masters just feel that this is very troublesome, so they will directly choose surface-mounted. They will also explain that it is easy to install, can dissipate heat in time and troubleshoot, if it is broken, it is easier to install, and if the dark wire is broken, it is only obvious to install. Hearing this, for non-professionals, even if they feel that the pretence is not good, they can only nod helplessly, the master's thoughts are really different from ours!

Therefore, whether the wires at home are well installed or installed can only depend on the factors you think you value more.

2. What are the construction skills of indoor circuit transformation?

In the installation, the pipeline should be installed before the wire is threaded. After the wire is loaded into the casing, the wire should be fixed with a clamp, which should be fixed in the wall and the wall first, and then plastered to conceal or conceal it with baseboards and decorative corners. The installation of the socket box should first make a hole in the wall

The cabinet is generally 2 or more, due to the excessive working current is not recommended to use the plug, must be installed separately leakage switch.

It is best to install a ground wire, which can prevent the air conditioner from leaking electricity and causing potential safety hazards.

Concealed circuit concealed sockets must be plastic products except for metal at the base, and they should be insulated.

Surface-mounted circuit sockets should all be exposed to the outside, and they should be protected from electric shock and insulated, so plastic products must be used.

The distance between the exposed socket and the wall is 23mm, and the distance between the dark rotation is 3mm

Trunking and wires.

Back boxes, panels, and trunking.

If you don't understand, it is recommended to entrust an electrician to buy it on your behalf. If the electrician asks you to buy it yourself, let the electrician open the list, and let the electrician open the specifications.

The trunking is wide and narrow (as shown in the figure above, narrow at the top and wide at the bottom), and it is purchased according to the length, how many x how many.

Wires surface-mounted 1 copper wires are fine, sockets, air conditioners, and electric water heaters copper wires are fine.

The requirement to be buried in the wall is thick.

The panel is just to buy an ordinary standard concealed panel, with an exposed bottom box (50mm high), about 1 yuan apiece. You can also buy an exposed socket switch with an integrated panel bottom box.

Surface-mounted sockets do not require a back box.

Switch types (one open, two open, three open, etc.), sockets (five holes, three holes (16a), multi-hole), switch sockets (one open five holes, two open five holes) and other specifications should be listed by the electrician, and you can buy it according to the order.

Generally, the quality of well-known brands is not bad, such as switches and sockets can be selected domestically, such as bull (more expensive), Zhengtai, Hongyan (Hangzhou), Delixi, Legrand, etc.

It doesn't matter if the trunking is not brittle and has good toughness.

Pay attention to the use of BV wire, the way to distinguish the quality of the wire. The first is to peel off the insulation layer and see what color the copper wire inside the wire is. If it's fuchsia, then it's a good quality wire.

If it's black, then it's of poor quality, don't buy it.

Zhengtai, Bull, Delixi, Hongyan, People, these brands are all available.

Electricity installed at home, some people upstairs said to find an electrician to buy, I don't agree with this way, those decoration electricians are making money from this aspect, asking them to buy, but it is a fake, you can ask him to make a breakdown, go to the regular decoration store to purchase, absolutely no fakes.

Hello, there are two ways. One is to ask an electrician to make a list and buy it in person at a physical store or online, which has the advantage of saving money and the disadvantage of being time-consuming and laborious; The other is to ask an electrician to help you buy it.

Call the electrician to give the data first, and then go to JD.com and the like to place an order.

Hello classmate, you can ask the electrician to buy these things, buy them yourself, buy brands, there are generally few fakes, and it is best to consult an electrician master if you don't understand electricity. Thank you.

Then you can go to a professional e-commerce company to buy it. The pros will tell you what kind of stuff to use. It is advisable not to take the bright line. First, it's not pretty. Second, the open line is easy to cause line fire.

Buy your own materials, calculate the amount, and then consider what to buy.

Materials: surface-mounted trunking PVC or PVC pipes or thin-walled iron pipes, with pipes, you have to consider fixing off the wall code or clips, and cooperate with box connections (locks, direct) surface-mounted 86 bottom boxes with a number of small yellow fish (self-tapping screws and plugs) insulating tape hole openers saw blades or wallpaper knives.

Panel socket switch rail gate (isolation, leakage, air opening) brand: Siemens, ABB, Schneider.

Wires, national standards, Kunlun, and white cats can be used in a way that must consider the use environment (fire-resistant wire, moisture-proof), and the electrical box calculates the gate position according to the circuit.