Is there a problem with foam coming out of the washing machine inlet box?

Updated on home 2024-06-28
21 answers
  1. Anonymous users2024-02-12

    1. It is possible that the water mark is adjusted too high. 2. It is possible to add too much clothing. 3. There is a possibility of laundry detergent.

    Or too much laundry detergent is added. Causing foam to come out of the water inlet box. Although it will not cause damage to the washing machine, it is also a violation of operating procedures.

    should be corrected.

  2. Anonymous users2024-02-11

    There is no big problem with foam coming out of the washing machine inlet box, which means that you have put too much detergent and the washing effect is poor.

  3. Anonymous users2024-02-10

    Washing machine does not get water reason:

    1) Please check if the faucet is not turned on;

    2) Please check whether the water pressure is relatively low;

    3) Please check whether the inlet pipe of the washing machine is bent; 4) Please check whether the washing machine program is set correctly;

    5) Please check whether the door of the washing machine is closed;

    6) Please check whether the water filter of the washing machine is blocked. 1. When washing clothes, inject very little water, put laundry detergent must be put less, if you put more laundry detergent, add water in a closed space to run, a large amount of foam will be squeezed out by the wind, resulting in foam overflow around the door ring. It is generally recommended that the amount of laundry detergent input is 1/3 of that of a straight washing machine of the same level.

    2. Drum automatic washing machine (washing machine capacity 3-9kg) The first step: pour a bag of laundry detergent into the washing machine barrel.

    Step 2: Close the side door of the washing machine, skip the pre-wash setting, directly select the main washing program, add water, and run the washing machine for about 5 minutes to dissolve all the detergents.

    Step 3: Turn off the power and soak for one hour.

    Step 4: Wash once according to the standard mode of daily washing (washing-rinsing-dehydration).

  4. Anonymous users2024-02-09

    It could be that the water inlet pressure is too high or the box is not tightly sealed, but it is not too much of a problem. It's just that it gets dirty.

  5. Anonymous users2024-02-08

    There is a problem with foam coming out of the washing machine inlet tank.ใ€‚

  6. Anonymous users2024-02-07

    Nothing is wrong, it may be that you have added too much laundry detergent.

    The drum washing machine originated in Europe, and the washing method is designed to imitate the principle of beating clothes with a stick hammer. The drum washing machine is made of stainless steel inner barrel, mechanical program controller, phosphating, electrophoresis, spraying triple protection of the shell, and a number of bulky cement blocks to balance the huge centrifugal force generated when the drum rotates to do repetitive motion, plus the joint action of washing powder and water to make the clothes clean.

    Advantages of laundry: The drum washing machine is controlled by a microcomputer, the clothes are not entangled, the washing is uniform, the wear rate is 10% smaller than that of the wave wheel washing machine, and it can wash cashmere, wool, silk and other clothes to achieve comprehensive washing. It can also be heated to fully dissolve the laundry detergent and give full play to the decontamination effect of the laundry detergent.

  7. Anonymous users2024-02-06

    Too much detergent, causing foam to bubble out of the washing machine inlet box.

    The inside of the washing machine looks very clean, but you don't know that there is also an outer sleeve on the outside of the washing drum when washing, and the laundry water goes in and out of the middle of these two layers, and the water is discharged in this interlayer, and the dirt inside the interlayer is very serious.

    The washing machine interlayer is actually like a sewer, its dirt is mainly composed of scale, laundry detergent free matter, fibers, organic matter, dust, bacteria and other garbage, these hodgepodge are firmly attached to the washing machine interlayer, multiply and ferment at room temperature, and the laundry will pollute the clothes to the human body, and even make people itch and allergies. When cleaning, pour the amount of water descaler (commercially available) for the three kettles into an empty container, prepare it according to the ratio of descaler water = l 2 and stir well.

    Pour the mixed descaler solution from the detergent addition box, being careful not to spill on the **. Then press the power switch of the washing machine, set the program to "Washing Program" (select the longest time), and make the washing drum rotate; After the descaling solution is discharged from the drain pipe into the barrel, the discharged descaling liquid is added from the detergent addition box, and so on many times until the program is finished, and the filter is opened to clean the filter.

    When the machine is finished, open the inlet valve and return the drain pipe to its original position. Re-select the washing program to make the washing machine run again, and when the program is finished, clean the filter again. At this point, the descaling and cleaning are complete.

    However, due to the action of descaling liquid, the surface of the washing machine drum will be slightly dark and black, but it will not affect the normal use, and the clothes can be restored to their original state after washing the clothes a few times.

  8. Anonymous users2024-02-05

    You're adding too much laundry detergent. The characteristics of the drum are that it saves water and electricity (compared with the wave wheel), and its water consumption is very small, so the added laundry detergent should also be reduced, and do not continue to use the drum with the habit of using the wave wheel.

    The problem you are reporting is that there is too much detergent, causing the foam (after the bubble bursts, it turns into water, and you think it is water) overflows through the gap in the washing box. What you should do is stop the work and go directly through the dewatering procedure to drain all the detergent in the barrel, and at the same time clean the sewage outside the machine and on the ground to prevent electricity leakage. Next, throw a few rags, do not add any detergent (do not add powder or liquid), and use the quick wash function to clean up the residual detergent in the cylinder.

    In the future, remember not to use a large amount of detergent, otherwise 1. Sewage overflow and pollute the home environment; 2. Damage to the machine, especially the paint surface of the machine; 3. It may damage the computer board and lead to scrapping. It is recommended to use low-foaming laundry detergent (laundry detergent is easy to produce a lot of foam, if it is marked as low-foaming, it can also be used) or special laundry detergent for rollers, and there is a special detergent for drum cleaning, and it is not recommended to use laundry detergent as a drum for cleaning. Usage above, strictly follow the instructions.

  9. Anonymous users2024-02-04

    Then how much laundry detergent or laundry detergent do you have to put in this one, and there can be so much foam.

  10. Anonymous users2024-02-03

    1. Obviously, there is too much detergent and the rinsing is not thorough, resulting in the foam in the gap between the two barrels, and the foam will come out when the dehydration rotates at high speed.

    Second, there is a tiny foreign body between the two barrels and there is detergent on it that has not been removed, because between the two barrels and the bottom of the drainage ditch is the closest, and the washing machine will have the bottom of the water and can not be put in, just the detergent on the foreign body and the water below the undrained water plus high-speed rotation, there will be foam.

    In this case, the best thing to do is to put less detergent or rinse a few more times, and at the same time wash the inside of the washing machine thoroughly to remove the washing residue.

  11. Anonymous users2024-02-02

    When water enters the washing machine, the reason why water can spill out of the side of the laundry detergent box is the laundry detergent in the detergent box.

    Put too much, as long as you clean the box yourself, it will be fine.

    If the amount of detergent (laundry detergent, laundry detergent) is too large, the foam will overflow to the machine through the laundry box, and the main effects are:

    1. Affect environmental hygiene;

    2. It may cause damage to the machine;

    3. Increase the number and difficulty of rinsing;

    4. There will be detergent residue on the clothes.

  12. Anonymous users2024-02-01

    When water enters the washing machine, water will spill out of the laundry detergent box.

  13. Anonymous users2024-01-31

    Summary. In the first case, when the water starts to enter, the water overflows from the drawer of the detergent box, which is caused by foreign matter flowing into the swirl rubber inlet pipe from the detergent box, blocking the water inlet, or because the laundry detergent used is highly absorbent, the detergent is not dissolved and compacted into a lump, blocking the water inlet of the whirlpool inlet pipe.

    When water enters the washing machine, water will spill out of the laundry detergent box.

    In the first case, when the water starts to enter, the water overflows from the drawer of the detergent box, which is caused by foreign matter flowing into the swirl rubber inlet pipe from the detergent box, blocking the water inlet, or because the laundry detergent used is highly absorbent, the detergent is not dissolved and compacted into a lump, blocking the water inlet of the whirlpool inlet pipe.

    At this time, the detergent box can be withdrawn, the upper lid of the washing machine can be opened, the detergent box can be disassembled, the swirling rubber water inlet pipe can be cleaned, and the foreign matter or laundry detergent can be removed, and the fault can be eliminated.

    In the second case, water spills out of the detergent cartridge at the end of the wash.

    This is due to the improper use of detergent by the user. This will not happen as long as you use a low-foaming or non-foaming detergent. If this happens, turn the program controller clockwise to the drain position to drain the water, and then rotate the program controller to the desired program, and the washing machine will continue to work normally according to the program.

    If you have any questions, you can always continue to ask me, I wish you a happy life! ๏˜๏˜

    Impurities enter the washing box, so that the washing box can not leak normally when water enters the water inlet pipe, resulting in the overflow of the washing box. If this is the case, the spill can be cleaned of the impurities in the washing box. The overflow of the washing box of the drum washing machine may also be caused by the viscous detergent used by the user when washing the clothes.

    If you use a detergent that is too viscous, it will be difficult for it to leak out of the leak hole of the washing box after pouring it into the washing box, which will also cause the washing box to clog and cause water to overflow.

  14. Anonymous users2024-01-30

    One is that the washing machine itself is not strong enough, resulting in incomplete rinsing, if the rinse is not thorough, it is actually a secondary pollution to the clothes, dirtier than not clean, and the strength itself is not enough, the motor is not good, and it cannot be moved; There is also an objective original closed inspection of the lead cause: laundry detergent or detergent is put too much during washing, resulting in rinsing is not clean, and now there are washing machines on the market that automatically put detergent, which is very convenient, but I am worried that users do not know how much to put in the new function.

    It may be that the laundry detergent has been misplaced and poured into a different compartment. Or there is residue in the washing box of the washing machine, because the daily residual detergent will solidify, which is easy to clog and cause foaming, so it needs to be cleaned frequently.

    Do not use laundry detergent as a washing machine cleaner when washing. Many families do not have a special washing machine cleaner, thinking that detergent and laundry detergent are an effect, so they will pour laundry detergent when using the "cylinder self-cleaning" mode, which is wrong, because "cylinder self-cleaning" is a high-temperature cleaning, which will cause foam to overflow.

    After washing the washing machine, there is no foam treatment:

    The laundry detergent is used too much, the program of the washing machine is set, and the clothes are not cleaned. After the rinsing program again, the fully automatic washing machine has an overflow function set during the rinsing program, so foam leaks when washing clothes. When the overflow function is set, the detergent foam generated by washing the laundry will float on the surface of the water when the laundry is rinsed.

    In order to remove detergent foam when rinsing clothes, there is an overflow port on the upper part of the washing machine barrel. When the fully automatic washing machine rinses the laundry, it rinses while filling the water, and the detergent bleach is continuously discharged out of the bucket through the overflow at the upper part of the washing machine barrel. With overflow rinsing, you can rinse clean clothes quickly and save time.

  15. Anonymous users2024-01-29

    When the washing machine enters the water, the water will overflow from the side of the laundry detergent box, and the laundry detergent will be put too much, and it will be good to clean the box.

    If the amount of detergent (laundry detergent, laundry detergent) is too large, the foam will overflow to the machine through the laundry box, and the main effects are:

    1. Affect environmental hygiene;

    2. It may cause damage to the machine;

    3. Increase the number and difficulty of rinsing;

    4. There will be detergent residue on the clothes.

  16. Anonymous users2024-01-28

    When the washing machine enters the water, the water will overflow from the side of the washing liquid box, indicating that the washing machine is out of order, you should find a qualified professional master who repairs the washing machine to help you take a look, help you check and repair, and will quickly help you solve the problem.

  17. Anonymous users2024-01-27

    When entering the rinsing program, the water will overflow from the laundry detergent box, first check the water distribution plate, and the three pipes connected to the water inlet box are blocked, and the bottom of the laundry detergent box is not deformed. If you haven't found the reason yet, then you can apply for repair, and ask a professional master to take a look.

  18. Anonymous users2024-01-26

    No, it should be uh, the box where you put the laundry detergent is blocked, or the water is too much.

  19. Anonymous users2024-01-25

    Put it in laundry detergent, put too much laundry detergent, it will be good to clean the box.

  20. Anonymous users2024-01-24

    No, I haven't encountered it, it shouldn't be like this, I don't know.

  21. Anonymous users2024-01-23

    Summary. Dear, hello, I am Zirou, a little expert in life, I am happy to answer your questions, why is there still foamy water after washing in the washing machine: two situations may cause this phenomenon.

    1. The laundry detergent or detergent used for washing clothes is not suitable for the washing machine. In the first case, the laundry detergent needs to be replaced. In general, whether it is a drum washing machine or a wave wheel washing machine, it is necessary to use a special machine washing detergent.

    If you really don't have it, you should also use low-foaming laundry detergent, so that it can protect both the washing machine and the clothes. 2. The inner cylinder of the washing machine needs to be cleaned. Due to the long-term lack of timely cleaning of the inner cylinder of the washing machine, there is a large amount of laundry detergent residue, not only laundry detergent residue but also a large amount of dirt and bacteria, which causes the problem that the washing machine is not clean.

    Dear, hello, I am a little master of life Zirou, I am happy to answer your questions, why is there still foaming water after washing the washing machine: two situations may cause this phenomenon. 1. The laundry detergent or detergent used for washing clothes is not suitable for the washing machine.

    In the first case, the laundry detergent needs to be replaced. In general, whether it is a drum washing machine or a wave wheel washing machine, it is necessary to use a special machine washing detergent. If you really don't want to return to Akeno, you should also use a low-foaming laundry detergent, so that it can protect both the washing machine and the clothes.

    2. The inner cylinder of the washing machine needs to be cleaned. Due to the lack of timely cleaning of the inner cylinder of the laundry huai machine for a long time, there is a large amount of laundry detergent residue, not only laundry detergent residue but also a large amount of dirt and bacteria, which causes the problem that the washing machine is not clean.

    In addition, it is best to clean it once every 2 to 3 months, so as to ensure that the clothes washed in the washing machine are cleaner. Find a professional cleaning staff to dig Xiangye or brand after-sales, and come to help with the inner barrel dismantling and washing service of the laundry judgment machine. Different brands charge different banquets.

    This is a common troubleshooting.

Related questions
9 answers2024-06-28

When using a fully automatic washing machine, it should be operated in the correct way, and the specific steps are as follows: >>>More

6 answers2024-06-28

The most common water inlet in the shutdown state is that the water inlet solenoid valve is faulty, or it may be that there is a problem with the computer board, but this possibility is relatively small, the simple judgment method is: turn on the faucet with water intake, unplug the power plug, if the washing machine is still flooded, you can confirm that the solenoid valve is faulty, and the water can not be turned off (in the case of power failure, the solenoid valve is closed), and the solenoid valve needs to be replaced. The best way is, of course, to ask the manufacturer to authorize the maintenance point to repair (in fact, the maintenance point must provide services as long as it receives a maintenance request, and the vast majority of the factory headquarters can provide services, however, it is not easy to say in some more remote places), if it is really inconvenient, the maintenance point can not come to the door, you can also ask the local qualified maintenance department to charge for maintenance, and the charge depends on your local situation. >>>More

17 answers2024-06-28

The current washing machine water inlet switch is a 220V solenoid valve, the water inlet solenoid valve of your Korean Electric 9ยท5kg automatic washing machine is at the back of the washing machine, the old washing machine water inlet switch is a mechanical and timer made together, the more old-fashioned is separate, the automatic washing machine is turned on to enter the clothes balance rotation, water intake, washing, dehydration, spinning ...... >>>More

17 answers2024-06-28

The water inlet pipe of the Yangtze washing machine is seven pipes. This totally accessible atmosphere is sufficient, not too long.

18 answers2024-06-28

Midea drum washing machine.

There are a lot of small blackheads in the inlet sink. >>>More