Can the speaker be hoisted to solve the resonance?

In general, yes. However, soft hoisting is not suitable for bass or subwoofers, because the speaker will shake when playing, resulting in poor bass effect. ”

Although it is said that the speaker may resonate, if it is suspended, the resonance situation will not be too fundamental, and the problem must be found from the speaker itself.

As far as I know, it's not possible, if it falls down and it can be solved, then it's too simple, this resonance is a problem that is generally inferior to the audio.

When the speaker is hoisted, can the resonance be solved? Most of it is Mother's Day, which is generally not of much use, but it must be let go.

Tianxiang is hoisted, it should be able to solve the resonance, pay attention to the connection of the silver horn when installing, and it must be strong.

Your situation in a box can't solve the resonance situation by lifting it up.

The main thing is to place the two speakers at a certain distance, so that they can produce good sound and there will be no resonance.

It is impossible to solve the resonance when the speaker is tuned, and if you want to solve the resonance, you must reset the sound.

The speaker can be hoisted to solve the resonance, because it still has vibration, so there should be a board underneath.

I just helped you inquire, this can be solved, just hang it up and hang it high.

Hanging up the sound can't solve the resonance, and there is no way to solve it.

The speaker should be able to solve the problem of resonance when it is hoisted.

It depends on how the installation is done, and you can ask the people in the physical store, and then you can ask the installers, and they can give you some good advice, which will help you have any questions about this in the future.

Loudspeakers hoisting up can solve the problem justly.

Do you want to hang up can solve the notarization? You should check the professional explanation of the speaker.

If you want to jump, you can solve it, and if you want to fall, you can also do it.

Can an impression drop solve the resonance? I think this drop can be solved justly.

Can it be solved? It should be solvable.

1. First of all, a small amount of asphalt is heated and melted into a molten liquid until there is green smoke and no longer bubbles.

2. Before pouring, take out the crossover, sound-absorbing materials and speakers in the speaker, and use a high-temperature-resistant small baffle (such as a small iron sheet) to block the speaker lead wire and the binding post bridge, so as not to be covered by the asphalt solution, and then remove the dust and wood chips and other debris inside the speaker. Between the front and rear panels, a supporting wooden strip connects the front and rear panels. After the preparation is completed, the melted asphalt is poured into the inner wall of the speaker in turn.

3. Pour one side first, and then pour the other side after the asphalt solution cools and solidifies. When pouring asphalt into the rear plate, do not pour the welding head of the binding post to death, so that there will be wiring when the speaker is welded.

4. It is necessary to ensure that the asphalt is poured evenly and smoothly. After the asphalt paving thickness is about 15 mm, the entire box should be cooled before the exterior decoration can be processed, and then the crossover, sound-absorbing materials, and speakers should be loaded. After the testing, tuning and other work is completed, it will be completed.

The speaker that has been treated in this way has better airtightness, and the lead can completely eliminate the resonance phenomenon in the box.

I haven't figured out whether the resonance you described is the resonance phenomenon of the cabinet, which is related to the sound material, a good wooden speaker can effectively reduce this resonance, what level of your audio is, and how loud the volume is when you use it, and what kind of space you place it looks like, these will affect the listening experience, for example, if you play too much in a small space, and the sound bass is too heavy, then you must feel that the roar is very serious, and there will be nausea for too long.

Ask this part of the speaker, sometimes the bass will have a resonant sound, and if you press it, it will be gone, but I feel that the overall bass sound quality has also deteriorated, what is the problem?

2. After the power amplifier is installed without problems, adjust the volume of the host and power amplifier to the minimum position, and then test the following functions at the frequency crossover point: (1) The crossover switch of the front sound field power amplifier is set at high pass, and the crossover switch is adjusted between 80hz and 120hz. (2) The rear sound field amplifier is also set at high-pass, and the crossover switch is set between 200Hz and 400Hz.

3) The subwoofer crossover switch is set at low pass, and the crossover switch is set between 80Hz and 120Hz. (4) Turn off or reset the bass frequency point booster of all power amplifiers to zero.

It is also possible that the audio is aging, and generally the 4S shop will provide maintenance functions.

Ask if the maintenance is not as good as before, and this resonance sound is not obvious and easy to repair.

The question is easy to solve with Vaseline in that place. Is it that the rubber edge inside is hard.

The connector connecting to the main unit is not properly connected

The tweeter diaphragm vibrates at a higher frequency than you may feel it. The tweeter cannot be directly connected to the power amplifier, it will burn out, and can only be accessed through the crossover. Your high pitch may burn out the moment it is spoken.

Hope it helps.

Of course, sound waves are a kind of energy, they fluctuate all the time, but you can feel some frequencies and some frequencies you can't.

How resonant speakers are used.

It is not fixed, reinforced, and the speaker base is equipped with vibration damping angle pads.

The resonant speaker should rest the slightly vibrating place on the table or something, so that the table vibrates and makes a sound.

The laptop is powered by batteries (unplug the mains outlet) to try, if it still doesn't work, it may be a matching problem between the notebook output and the speaker input, you can try to connect a 75-300 resistor in parallel to the common end of the left and right channels at the speaker input.

I'm doing speaker engineering.,It is recommended that you buy a speaker and go to the store to see the real thing,Audition! What is said on the Internet is empty, and you have to try it out to know the effect! Our company has the kind you request, but this kind of speaker effect is generally not good!