How to take the toilet down, how to take off the lid of this toilet?

01 Check the toilet for cracks first.

Please pay special attention to the place where you need to lift the toilet with your hands, because the toilet is made of ceramic magnet and can cut people like glass, so wear thick work gloves when moving the toilet.

02 Pick up the tank lid – Remove the tank lid and bring the lid to a place where it won't be touched.

03 Turn off the water source.

The location of the water valve is on the left side of the toilet.

04 Rinse the water out of the tank, press the flush handle until the water runs out completely, wear rubber gloves, and use a sponge or towel to dry the water in the tank.

05 Use a small disposable container to scoop up the remaining water in the toilet bowl and use a sponge or towel to dry the remaining water in the toilet bowl.

06 Remove the connected water pipe from the toilet bowl and pour the excess water into the bucket.

07 Connect the water tank to the toilet seat. The bolts may not come out, and it can take hours to remove the tank from the toilet seat.

08 nuts.

Remove the bolts from the fixing ones, and sometimes the bolts will turn, so use a hacksaw to cut the bolts.

You can buy a single-handle saw for easy use in a work area where space is limited.

09 If the toilet seat is glued to the floor with gap filler, use a tool to handle the sealant.

Cut. 10 Gently shake the toilet bowl to loosen it from the sticky sealant.

11 Ask another person to help lift the toilet. Keep your back straight and support your weight with your legs.

Put the old toilet bowl that you have dismantled in a place where it will not get in the way of work, and put a rag or towel underneath it as it will be a little dirty. Otherwise, you can put it on a rag or plastic sheet and drag it away.

12 Plug the drain with rags so that the gas from the sewer does not escape.

13 If the fixing bolts are broken, remove them and replace them with new ones.

14 Use a putty knife to scrape off the flange and the old sealant on the floor.

There is a wallpaper knife to disconnect the glue at the joint between the toilet seat and the ground. If the glue hardens, you need to cut it off patiently.

Generally, the toilet bowl can be removed with force. If you don't have enough force, try wearing soft-soled shoes and kicking them hard from the side to get off the ground. Pay attention to the strength of the mastery, do not over-kick and cause the toilet to roll over. It's best if another person is close to the toilet for protection.

Because the toilet bowl will be dirty after a certain number of years, you can use some cleaning products to clean it before installing it.

Turn off the water switch in the house and remove the water pipe fitting from the toilet.

Remove the screws on both sides of the toilet seat.

If the water tank and toilet are separated, flush the water from the water tank first, then scoop the water in the water tank as much as possible, take off the water tank, and then hold the toilet up.

The connection between the bottom of the toilet bowl and the ground is generally made of glass glue, and it is necessary to use a blade to cut along the bottom of the toilet bowl and the ground, and it is easy to move away.

Your toilet seat may be secured with cement or glue, which can be shoveled through the bottom seam with a very thin piece of steel. It's even more troublesome if it's cement.

The method of removing the toilet lid is as follows: the bolts of the toilet bowl have a very thin protective lid on it, and you can use a screwdriver to pry it up along the edge.

When replacing the toilet seat, you can replace it by removing the fixing bolt on the back of the toilet bowl and operating in the opposite direction when installing. Most toilet seats are large or small, and you can simply adjust the two bolts when installing. However, it is also necessary to measure the size, the distance between the screw holes, the width and length of the toilet seat, and then buy a new toilet seat to replace it.

Find the screw cap, remove it with a wrench, and replace it with a new one. Generally, the position of the screw cap is not easy to find, some are in the light, and some are in the dark. In the dark place of the screw cap, inside the toilet bowl against the side of the tank, open the lid.

If you put your hand in it and touch it upwards and in the direction of the tank, you should be able to touch it, but you can't see it.

Standard Answer: Unscrew the small screws on the left and right sides (just in the open place, at both ends of the lid hinge), then open the cover to 80 degrees and gently pry it open to the left with a flathead screwdriver.

The arrow points to misleading! Below is the direction of my fingers, there is a screw on the left and right sides, and you can remove the toilet seat by loosening it.

The bolts of the toilet bowl have a thin protective lid on top of it, and you can use a screwdriver to gently pry it up along the edge.

Toilet seat replacement method 1:

Some toilet seats are fixed with screws, at this time, you only need to find the screw cap, use a wrench to remove the screws, and then replace them with new ones. The screw cap installed in the open place is easy to unscrew down directly, and the screw cap installed in the dark place is not visible, and it is generally located on the side of the water tank in the toilet, and it can generally be found by touching the direction of the water tank after opening the lid.

FAENZA bathroom FB1636 one-piece toilet.

Toilet seat replacement method 2:

If the toilet is secured with a set bolt, the toilet lid can be removed by simply removing the fixing bolt at the rear of the toilet bowl when replacing the toilet seat. After measuring the size, the distance between the screw holes, and the width and length of the toilet seat, buy a new toilet seat to replace it, and operate in the opposite direction when screwing the screws during installation.

Toilet seat replacement method three:

Different styles of toilet lid installation are also different, and the position of the bottom end of the toilet lid connected to the toilet bowl is fixed with screws, as long as the hand reaches down to the back of the toilet bowl to find the screws on both sides and unscrew, you can take off the entire cover, and then replace the toilet cover, this way is also the most convenient.

FAENZA Bathroom FB1671-2 Smart Toilet.

Toilet seat replacement method four:

Of course, if these simple disassembly methods do not work, the top ten bathroom brands FAENZA bathroom recommends finding a professional to dismantle and replace, remember not to forcibly disassemble it yourself, so as to damage the toilet bowl. At present, many bathroom brands also provide free door-to-door replacement services for toilet seats, as a responsible national bathroom brand, FAENZA Sanitary Ware strives to provide consumers with comprehensive and meticulous consumer services, and can also unconditionally provide replacement toilet cover services for consumers who purchase FAENZA products.

How to dismantle the toilet, let's take a look at the specific disassembly steps.

Prepare tools before disassembling the toilet, usually you need to use a screwdriver, wallpaper, knife, gloves, towels, etc.

Remove the lid of the water tank first so as not to hit yourself, close the water valve, and clean the water mass in the water tank and toilet.

The bucket can be long pressed to flush the flush button, and the toilet can be scooped out with an old towel or small box.

Remove the connecting water pipes and connectors in the water tank, it doesn't matter if you can't dismantle it, you can finally solve it by force.

Generally, there will be a circle of glue under the toilet, which is cleaned with a wallpaper knife.

Shake the toilet vigorously and ask someone to help lift it up.

6 key points to choose a toilet.

Clause. 1. Look at the glaze of the toilet, mainly to see its finish, you can use the flashlight of the mobile phone to irradiate the inside of the toilet, carefully observe the reflectivity of the toilet from the side, and check whether there are fine trachoma and pittings on the surface.

Clause. Second, the molding of the toilet, the one-piece toilet occupies a small area.

Clause. 3. Look at the weight of the toilet, the heavier the toilet, the better the quality, and the whiter the collapsed part without glazing at the bottom, the better.

Clause. Fourth, look at the glazing process, it is best to choose the dry glaze process, which is more strong.

Clause. Fifth, see whether the storage bend is fully glazed, and all the parts of a good toilet will be fully glazed.

Clause. 6. Look at the water parts, listen to the sound made by the water parts, and press the flush switch to the end to make a crisp sound. <>

The operation of removing the toilet bowl is as follows:

1. Check whether the toilet has pear marks before disassembly, if there are pear marks, it is easy to be injured when dismantling, and protective measures should be taken. Then remove the water tank and turn off the water valve at the same time, flush the water in the tank and clean the inside of the water tank. Next, clean up and dry the remaining water from the toilet, then remove the hose that connects to the toilet.

2. Some toilets and water tanks are connected tightly, it is difficult to disassemble, in this case, the water tank should be removed first, if it is difficult to disassemble, then you can use a hacksaw to cut the bolts, if the toilet is installed when the gap is filled, then you should use a tool to cut the glue first, and then slowly shake the toilet bowl and lift it gently, so that the toilet bowl is disassembled.

Toilet Buyer's Guide

1. Observe the gloss of the toilet. The higher the gloss of the product, the higher the density, the easier it is to clean and hygienic. This is because the quality of porcelain is directly related to the life of the toilet, the higher the firing temperature and the more uniform, the better the porcelain.

2. To see whether the glaze is uniform, consumers can ask the store whether the sewage outlet is glazed, and even put their hands into the sewage outlet to feel whether there is a glaze in the return inlet. The main culprit of hanging stains is the poor glaze, customers can touch it with their hands, and the qualified glaze must be delicate to the touch.

3. There are two ways to save the water consumption of the toilet, one is to save the water, and the other is to save water through the reuse of wastewater. Water-saving toilets have the same function as ordinary toilets, and must have the functions of saving water, maintaining cleaning and transporting excrement.

Generally, the toilet seat is fixed with screws, at this time, you only need to find the screw cap and use a screwdriver to screw it off, and the toilet seat can be removed.

The screw cap installed in the open place is easy to unscrew directly, and the screw cap installed in the dark place is not visible, and it is generally located on the side of the toilet bowl near the water tank, and it can generally be found by touching the direction of the water tank after opening the toilet lid.

If the bottom of the toilet lid is attached to the toilet bowl with a fixing bolt, simply unscrew the fixing bolt at the back of the toilet bowl when replacing the toilet lid.

The toilet seat can be removed. Then buy a new toilet seat to replace it, and operate it in the opposite direction when screwing it when installing.

Now there is also a quick-release toilet seat, as long as you press and hold the movable screw at the root of the toilet seat with both hands, you can lift the toilet seat.

The toilet seat can be said to be an important part of the toilet, when the toilet will be dirty or damaged after a long time, this time will choose to replace a new toilet seat. Let's introduce to you how to take off the toilet seat.

At present, there are many toilet styles on the market. However, different styles of toilets will have different ways of installing lids, but most of the toilet lids are connected to the toilet at the bottom and then fixed with screws, so we just need to find the corresponding position and use a wrench or other tool to unscrew all the screws, so that the entire toilet lid can be removed.

How to change the toilet seat correctly.

1. There are many different styles of toilets on the market, so there will be some differences in the installation of the toilet cover, generally speaking, the toilet lid is connected to the bottom of the toilet bowl and fixed with screws, then you only need to unscrew the screws to remove the toilet cover, and then replace it with a new toilet lid of the same model at this time.

2. Some toilet screws are located in the dark, so at this time, you need to open the lid on one side of the water tank to find it, and remove it with a live handshaker after finding it, and then replace it with a new one.

3. In fact, it will not be difficult to change the toilet cover, just remove the bolts that fix the toilet cover, screw the bolts in the opposite direction during installation, and then pay attention to the size of the bolts, and then adjust them, and then they can be fixed.

4. When replacing the toilet cover, in addition to the above methods of replacing the toilet, there will be 2 round screws at the root behind the toilet cover, then these 2 round screws are used to fix the toilet cover.

5. Precautions for replacing the toilet.

a. When buying a new toilet seat, you should buy the same as the original model, so you must first measure the hole spacing, length and width, and take a picture with your mobile phone, so that it is good to choose the type when buying.

b. When installing, be sure to align the position of the toilet cover, and then install it. Before installation, remember to clean the toilet first, and the screws must be tightened when installing the toilet lid, otherwise it will shake and reduce the service life.

Summary: The relevant content on how to take off the toilet lid is introduced here, which can be determined according to the style of your toilet to see which way is more suitable, I hope the above introduction will be helpful to you.

Problem 1: The toilet seat is broken. How to dismantle! Look at the picture! I can put my hand under the toilet bowl and there is a screw underneath. Just twist it away. At the beginning, my husband and I studied for a long time...

Question 2: How to remove the toilet lid The old-fashioned one is screwed and fixed on both sides. The new style is fastened with a buckle, and there is generally a button on both sides of the bottom, which is held down and unplugged.

Question 3: How to remove the toilet bowl in good condition Generally speaking, the toilet installation is glued with glass glue, you can use a blade to make a circle, if you use cement, you can only buy a new one.

Question 4: How to remove the toilet lid? I just bought it, read the manual, or ask someone to help

Question 5: How to remove the buckled toilet lid Look at the bottom of the toilet bowl There is something ding.

It is not the inside that is the bottom.

If not, go to the nearby market and ask the ** merchants of this brand.

Question 6: How to remove the toilet seat and clean it Unscrew the plastic screws on the back, and you can directly remove the toilet seat for cleaning.

Question 7: How to disassemble the toilet? What are the methods of toilet disassembly?

Kick the side of the toilet with your foot, all the way until it is separated from the ground, rest assured, it won't be broken. After loosening, remove the connecting pipe at the back. Put the toilet down, remember:

Put a towel on the part that fell to the ground, cut off the old rubber with a utility blade, and use a hair dryer to dry the cut rubber area. The second step is to treat the ground and sewer sections, tapping and drying in the same way. When you're done, put the toilet in the right place and move it to the drain place, remember:

The toilet spout must be aligned with the drain! After putting it down, draw a mark with a marker pen on the outer ring of the toilet, move the toilet, use structural glue to mark the inner ring of the mark on the ground, and then lift the toilet up, remember to be in the marked position, and then sit firmly, then the excess glue will be squeezed out, and the excess glue will be applied to the connection between the toilet bowl and the ground along the toilet bowl by hand, and the joint will be connected, and the completion will be completed. The glue is maintained for 24 hours and is usable.

Don't forget to use structural adhesives!

Question 8: How to disassemble and assemble the toilet lid Some toilets have nuts on the back. Some toilet seats can be pressed down there. Look at yours of the kind.

Question 9: How to remove the toilet lid Under normal circumstances, there are screws on the shaft of the toilet lid close to the water tank, and this screw is generally under the toilet bowl or there is a nut inside the water tank, which can be touched by hand.

There is also a buckle cover on the shaft near the water tank, and the screw cap can be seen when the buckle cover is opened.

Question 10: How to remove the toilet lid** At the back of the toilet, the bottom surface of the plane, there is a screw on each side, unscrew the screw mother counterclockwise, and take the toilet lid up and down, if the screw is rusty, then you can only use the hacksaw blade to sawn off the --- from the upper plane of the toilet