What cleaning agent is used for the sink and how to clean and disinfect the pool?

1. Iron pool.

The pool should be cleaned frequently, please use a sponge or cotton cloth to clean the pool, and use a neutral detergent to gently scrub; After the pool is used, wash it with clean water and wipe it dry, do not let the water droplets remain on the surface, the water with high iron content may cause the formation of brownish-red water traces on the surface of the pool; Trapped moisture can lead to mineral deposition, in which case a low-concentration vinegar solution can be used to remove this deposit, and finally completely washed off with clean water.

Note that do not use steel wool balls to scrub the pool, as scrubbing the steel wool balls will leave scratches on the surface of the pool and cause metal particles to adhere to the basin wall, resulting in rust spots; Clean the pool and avoid using a rough brush to avoid scratching the surface of the pool; Do not use rubber pads in the pool, as the dirt under the rubber pads is difficult to clean; If there are water spots in the stainless steel pool, you can use neutral detergent or cleaning agent to brush it.

2. Porcelain pool.

Porcelain pools are used for a long time, leaving behind brown rust stains that wash down the pipes. First of all, prepare salt and vinegar, mix salt and vinegar together, stir, let the salt be fully diluted in the vinegar, and then heat, after heating, use an absorbent sponge or rag to dip the liquid full, and then put it in a rusty place, cover it for 20-30 minutes, and after half an hour, then use a rough cloth dipped in salt and vinegar mixture, scrub hard, and it can be easy to remove stubborn rust.

Just use detergent or alkaline noodles, the effect is good.

How to clean and disinfect the pool:

1. Arrange cleaning personnel. In order to prevent the staff from carrying germs into the tank, the staff should be made to wear clean clothes and use long boots. Gloves and raincoats should be disinfected with a disinfectant solution with an effective chlorine of 50 100 ppm.

2. Close the water inlet valve, calculate the water inlet and water consumption, and decide the time to close the valve to reduce the waste of water.

3.Use a high-pressure washing machine or manual brushing to remove silt and debris at the bottom of the pool.

4. Drain sewage.

5. Add 20-30 cm of water.

6. Rinse the entire pool wall with high-pressure water.

7. Thoroughly remove the washed sludge and dirty water again.

8. Put in clean water, clean the wall and bottom of the pool again (many times) and drain it.

9. After slightly drying, spray with 1:20 chlorine dioxide disinfectant (chlorine dioxide disinfectant is equipped with 20 kg of water per bottle) and keep it for 30 minutes. The disinfection sequence is around the hole.

Water pipe parts such as water inlet pipes. Roof. wall coverings.

Finally, there is the bottom of the pool.

10. Put in clean water and add disinfectant. Soak at 50 100 ppm for 30 minutes and drain with a water pump. (Green Pioneer chlorine dioxide disinfectant solution with 200-400 kg of water per kg).

Disinfection is carried out twice: after the first disinfection, it is left for more than 30 minutes for the second disinfection, and then for another 30-60 minutes. After the disinfection work is completed, it is not allowed to enter the water tank.

Benefits of pool cleaning.

During the use of the cistern, some biological impurities are generated: aquatic organisms (such as algae) and bacteria, microorganisms, natural organic compounds (such as humic acid), etc. It is reported that there are currently 2,221 kinds of organic matter known in water, some of which are carcinogens.

Long-term non-cleaning of the pool will seriously endanger people's health, pool cleaning can effectively kill bacteria and microorganisms, and can avoid the water quality from hardening, reduce the incidence of disease infection and stones.

Cleaning: shovel out the sediment and various sediments in the pool;

Use a broom or nylon brush to repeatedly brush from the top of the pool, the surrounding walls, and the bottom;

If it is still not clean, brush again until it is clean.

Disinfection: Use a broom or nylon brush to dip a 1:100 sterilized water solution (or the disinfectant water solution prepared by the epidemic prevention station, and repeatedly brush and disinfect in turn; After that, cover the pool and close it for half an hour;

Rinse the entire pool with clean water and drain the disinfectant water solution;

Rinse with clean water again and drain the disinfectant solution.

Water injection: After all the cleaning and disinfection work is completed, clean up and pack up all the tools. Open the gate valve to fill the pool with water, and cover and lock it when the water level is reached.

Answering the disinfection method of tank water and well water, the continuous chlorination disinfection method is to use the "drinking water continuous sterilizer" to continuously disinfect tank water and well water. The dosage of water disinfection in each tank is calculated according to every 100L of water (i.e., two loads of water), adding 1 2 tablets of bleaching powder or 1 2g of bleaching powder, or bleaching powder, and the water with heavy pollution is taken as the higher value. The addition is the same as the disinfection well water, after adding the disinfectant, stir it with a water scoop or a clean special rod to fully mix it with the water, and ensure that the disinfection time is not less than half an hour.

Personal drinking water disinfection is still one of the forms to solve the temporary drinking water needs of disaster victims due to the sudden occurrence of flood disasters and difficult conditions, and the difficulty of initial water supply or water treatment.

Use a broom or nylon brush to repeatedly brush from the top of the pool, the surrounding walls, and the bottom;

If it is still not clean, brush again until it is clean.

Disinfection: Use a broom or nylon brush to dip a 1:100 sterilized water solution (or the disinfectant water solution prepared by the epidemic prevention station, and repeatedly brush and disinfect in turn; After that, cover the pool and close it for half an hour;

Rinse the entire pool with clean water and drain the disinfectant water solution;

Rinse with clean water again and drain the disinfectant solution.

Water injection: After all the cleaning and disinfection work is completed, clean up and pack up all the tools. Open the gate valve and fill the pool with water.

Units engaged in the cleaning and disinfection of secondary water supply tanks and pools must have professional qualifications and health permits for cleaning and disinfection, and operators must hold valid health certificates before they can operate. During the SARS period, the temperature measurement and registration of workers should be done twice in the morning and evening, and if the body temperature is abnormal, they should immediately seek medical attention and stop cleaning operations; All tools used in cleaning and disinfecting water tanks and pools should be disinfected; Workers must wear disinfected work clothes, work boots, and work hats before entering the operation area. Before cleaning and disinfection, a cleaning notice should be posted to inform residents and property rights units; When cleaning and disinfection, the inlet and outlet valves of the storage tank should be closed first, and the sewage valve should be opened to remove the water in the pool.

After the pool is cleaned, the pool must be disinfected; After the disinfection is completed, the disinfection record of the secondary water supply system must be made, and the CDC of the jurisdiction shall be notified to conduct on-site testing of residual chlorine, and water samples shall be collected for testing.

Summary. Citric acid cleaners can be used, and the acidity of citric acid can be used to effectively remove limescale.

What cleaning agent is used to clean the living water tank.

Citric acid cleaners can be used, and the acidity of citric acid can be used to effectively remove limescale.

1. It can be cleaned and descaled with water tank detergent. Conventional cleaning agents cannot completely remove limescale and acids from the waterway, and sometimes large pieces of limescale can be soaked off, but this will clog the waterway, and sometimes the water tank must be removed for cleaning. If you use the best powerful cleaning agent, the scale will appear as a powder suspended in the coolant and will not clog the water channels in the engine.

Hello, my home is self-dug well water supply, because it has not been used for a long time, the water tank has stinked, cleaned several times, the water still smells, what should I do?

Citric acid cleaners can be used, and the acidity of citric acid can be used to effectively remove limescale.

Can be cleaned with tank cleaner for descaling. Conventional cleaning agents cannot completely remove limescale and acids from the waterway, and sometimes large pieces of limescale can be soaked off, but this will clog the waterway, and sometimes the water tank must be removed for cleaning. If you use the best powerful cleaning agent, the scale will appear as a powder suspended in the coolant and will not clog the water channels in the engine.

How much citric acid to use?

After using the above citric acid to clean, there is no taste.

Dear, follow the instructions above.

Where is the manual?

Where can I buy citric acid?

Grocery? Dear, if you buy citric acid, there is an instruction manual, and every product has an instruction manual, if there is no instruction manual, it is fake.

Citric acid is bought at a chemical supply store.

Is citric acid toxic?

Dear, citric acid is non-toxic and is specially used for cleaning, for example, citric acid is added to dishwashing detergent, so it is non-toxic.

In order to relieve physical and mental fatigue and improve the comfort of bathing, many users now install bathtubs at home. If the bathtub is not cleaned for a long time, a lot of dust and dirt will accumulate, which is easy to breed bacteria. What cleaner do you use to clean your bathtub?

You can go to the shop to buy a special bathtub cleaner to clean, this cleaner can effectively remove the scale, stains, soap stains and other dirt on the surface of the bathtub, and will not cause damage to the bathtub, in addition, you can also use vinegar, baking soda, bleaching powder, etc. to clean the bathtub, which can effectively remove the dirt on the bathtub.

What to pay attention to when cleaning the bathtub.

1. If the surface of the bathtub is just an ordinary stain, we can use a soft cloth dipped in some water to gently wipe it; If it is mold, you can use a soft brush dipped in some toothpaste or bleaching powder to gently scrub; If it is a stubborn stain, it is recommended to use a professional cleaner to clean the bathtub quickly.

2. After the bathtub is used, it needs to be cleaned in time, not not cleaned for a year and a half, if it is not cleaned for a long time, the dust in the bathtub is easy to accumulate in large quantities, and bacteria are easy to breed in large quantities, which will pollute the environment of the bathroom space, endanger human health, and shorten the service life of the bathtub.

3. When cleaning the bathtub, you can use a sponge or soft cloth, and do not use a hard brush to scrub it, so as not to damage the surface of the bathtub.

4. If there are scratches or damage on the surface of the bathtub, you need to contact professional maintenance personnel immediately for on-site maintenance, so as not to affect the performance of the bathtub, and even cause problems such as water leakage and rupture of the bathtub. In ordinary use, we should not use hard objects to knock or impact it, and avoid violent use to avoid bruises or scratches.