How to repair a leaky toilet and how to fix a leaky toilet

1.First, use a knife to cut the glass glue at the junction between the toilet bowl and the floor tiles, and then unscrew the bolts that hold the toilet open.

2.Raise the toilet a little higher. Never pull or push the toilet bowl into place. It is more troublesome to break the sewer pipe.

3.Then check the sewer pipe for cracks, and then connect a PVC pipe of the same thickness, stick it with PVC, put the toilet on the top and try it, maybe the length is not suitable, and then use a saw blade to see until the toilet can stabilize and stick to the floor tiles.

4.Test the water and it won't leak. Glue the base to the floor tiles with glass glue and tighten the screws to secure the toilet. Don't shake the toilet back and forth for three days. Just wait for the glass glue to dry.

Caused by installation errors or broken flanges.

The specific steps are as follows:

1. The bottom edge is leaking, which may be caused by installation errors or broken flange rings, it is recommended to remove the toilet, reinstall it, or replace the flange ring.

2. If it is caused by the poor sealing of the bottom of the toilet and the floor tiles, that is, the glass glue is opened, it is recommended to remove the old glass glue and re-enter the high-quality glass glue seal.

3. If the bottom of the toilet is cracked and leaking, the crack is not large, it can be filled with colloid, if the crack is large, it is recommended to replace the toilet.

4. Toilet leakage, in addition to the quality of the toilet itself, it is also possible that the quality of the water valve pipe is not good, and it is damaged, causing water leakage. In addition, if the drain valve is not tightly sealed, it will also cause the toilet to leak.

Toilet leakage maintenance method: the water tank is leaking, and the water inlet group or outlet group needs to be repaired or replaced; The bottom of the toilet is leaking and needs to be resealed; If there is water seepage on the surface of the toilet, the toilet needs to be replaced.

1. Water tank leakage

Open the water tank and see that the water in the water tank is full, and the water flows out of an overflow pipe, indicating that the inlet group of the flush toilet is damaged, if you hear that the water tank is full of water for no reason, it means that the water outlet group is broken. This necessitates the repair or replacement of the inlet or outlet group.

2. The bottom of the toilet is leaking

If water leaks from the bottom of the toilet after flushing and is accompanied by a foul smell, then it can be determined that the seal between the drain pipe at the bottom of the toilet and the toilet is not good enough, which requires a new sealant.

3. There is water seepage on the surface of the toilet

If there is water seepage on the surface of the toilet, it is possible that there is a crack in the toilet itself. The detection method is very simple: first turn off the water inlet valve, then drain the water in the toilet tank, and then add red ink or ink to the residual water tank, wait for 30 minutes, and observe where the water seeps.

In this case, it is not recommended to repair the toilet, only to replace the flush toilet.

The reasons why a flush toilet leaks are:

1. The internal parts of the water tank are old. At present, there are many flush toilets on the market, and some small manufacturers produce a flush toilet of inferior materials in order to seek more benefits, which is often not visible on the surface, but it has not taken long to cause all kinds of problems.

2. The problem of sewer pipes. The solution to the problem of sewer pipes is to carefully check whether the interface between the toilet and the sewer pipe is loose, or to see if the sewer pipe is rotten.

3. Problems with drain valves. If the problem of the drain valve causes this phenomenon, it is recommended that you can ask a professional maintenance personnel to come to the door to repair it to ensure our normal use.

Here's how to fix a leaky flush toilet:Materials: Slotted taper, rubber sheet, double-sided tape.

1. First remove the lid of the toilet water hail rental box, so that you can see the toilet flush valve group.

2. Pull the toilet suction valve group up to take out the valve group.

3. The blue cover of the valve group can be removed by turning it outward.

4. After that, you can see the pumping valve of the toilet pumping component, and the middle of the bottom of the pumping valve is a sealing ring, if the sealing ring is not tight, it will lead to water leakage.

5. Quietly remove the gasket under the sealing ring, glue the thin sheet to the bottom of the sealing gasket with double-sided tape, fix it and then install it back, so that the toilet will not leak.

1. If the toilet switch is not reset, the toilet switch needs to be reset again. 2. If the quality of the flush toilet is caused by the leakage of the toilet, you can ask the installer to replace the toilet with a new one. 3. If the rubber ring of the toilet is not well sealed, you can replace it with a new rubber ring.

Relevant knowledge popularization: 1. When purchasing a toilet, the material must be selected correctly, and it must meet the standards of accessories, so that the service life will be longer, and the installation conditions should be fully considered. 2. When using the toilet, you must pay attention to cleaning the toilet, especially the inside of the toilet.

If not cleaned in time, it will lead to the production of various bacteria, which is not only harmful to human health, but also affects the use of the toilet. 3. If you find that there are any abnormal parts in the toilet, you must replace or repair them in time, and generally speaking, the parts in the toilet can be repaired by yourself. For example, the inlet valve can adjust the size of the inlet water in the inlet valve.

If there is an abnormality in the inlet valve, the valve can be adjusted appropriately. Or after a long period of use, the button of the toilet will also deteriorate, resulting in the inability to press and flush. You can replace the button with a new one or use a special lubricant to stop the button from stuttering.

Causes of toilet leakage:

1.Inferior material: Some manufacturers blindly reduce production costs, and choose inferior materials to cause cracking at the outlet of the inlet valve and the inlet pipe itself during injection molding, resulting in sealing failure, and the water in the water tank flows into the toilet through the overflow pipe of the drain valve, resulting in "long flowing water".

2.When the water submerges the float (or floating bucket), the inlet valve still cannot be closed, so that the water continues to flow into the water tank, and finally flows into the toilet from the overflow pipe to cause water leakage. This phenomenon is especially noticeable when the tap water pressure is high.

3.Improper design: the mechanism of the water tank accessories interferes with the operation and leads to water leakage.

For example, when the water tank is discharged, the float and the float rod will affect the normal reset of the flap and cause water leakage. In addition, the float rod is too long, and the float is too large, which causes friction between the water tank wall, affects the free lifting of the float, and leads to seal failure and water leakage.

How to repair a leaky toilet:

1.Check if the flush switch is reset. The plastic flush switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored. Generally, the switch can be reset by repeating it several times.

2.Check whether the rubber gasket of the drain port under the ball valve is aged and the seal is not tight, and the problem needs to be replaced.

3.Check the spherical float of the tank with the water inlet switch. Whether the connection is loose, whether the float is in place and whether the switch is not turned off, resulting in non-stop water intake, and the water flows out from the upright drain pipe after it is full, as long as the connection between the float and the water valve switch is tightened.

4.If the rubber ball valve is damaged, the seal is not tight, and there is a water leak, it needs to be replaced immediately.

5.Water tank leakage, basically a drain valve problem, check the water tank outlet rubber plug, if the water outlet rubber plug is damaged or there is a foreign body blockage resulting in the rubber plug is not tightly sealed, it will also cause the toilet to flow more than once. If the water supply pipe in the tank is not placed correctly, it will also affect it to a greater or lesser extent.