How to repair the toilet float, how to repair the toilet tank float is broken?

Toilet float valve repair steps:

1. Please make sure that the closing valve of the toilet is in the closed position.

2. After removing the valve plunger, you will see one or two gaskets.

or Type 0 seals.

If one of these parts fails, the water will continue to flow through the valve plunger and the toilet will keep running, so check all gaskets for damage and replace them.

3. If the float valve is sealed, replace it entirely. Turn off the water source from the toilet at the water closer, then flush, drain the water from the tank, unscrew the float arm from the old float valve, and remove the water fill pipe from the water pipe.

4. Look for the connecting nut under the water tank.

or a sliding nut, from where the inlet pipe enters the bottom of the tank. Loosen the connecting nut, remove the inlet pipe, and then under the tank, use an adjustable wrench.

Clamp the lock nut or locknut, which are above the slide nut, in the tank with another wrench to grip the base of the float valve shaft.

5. Take out the old device in the water tank, remove the gasket at all the connections inside and outside the water tank and keep it, the new valve may have a new gasket, but the old parts should be kept until the installation of the new device, so as to avoid damage to the new device during the installation process.

6. Insert the new float valve into the water tank hole, and after installing the gasket in the water tank, tighten the locknut outside the water tank, so that the internal gasket is tightly pressed on the water tank hole to play a sealing role, but do not overtighten it.

7. Replace the connecting nut and water inlet pipe, and install the floating arm from the new, and then insert the injection pipe into the water pipe.

8. Re-let the water flow out on the closed valve of the flush toilet, check whether there is water seepage in each part, and of course, check whether the float scrapes the back wall of the water tank.

9. The new float valve omits the floating arm and float ball, and uses the material cup. Once the tank is full, the cup will float up to cut off the water source. The water level of the tank can be set by adjusting the position of the cup on the lever.

One of the advantages of this float valve is that it allows the tank to be drained at full speed until it is full. It then immediately turns off the water, so it doesn't make a noise as the floating arm gradually closes the valve, as some flush toilets do.

The water supply valve can be replaced, and the float is a component of the water supply valve.

1.Buy some caustic soda, you can use freshly boiled water to melt the caustic soda, then pour it into the toilet, wait about 20 minutes for the toilet bowl to become very smooth. 2.

Clean the toilet with an appropriate amount of oxalic acid to neutralize the urine alkali and achieve the purpose of making the toilet unobstructed. 3.In addition to chemical cleaning, we can also buy a manual unclog ourselves.

In general, you can choose to use a state Oak Smart hand pressure uncrusher. This is more convenient to use. If you are cleaning the toilet bowl for money, you should make sure that there is enough water in the toilet tank.

If we don't have enough water, it's hard to clean up, and we risk overflowing the contents of the toilet. 4.One way to do this is to use a steel wire to stir it.

Generally, this hand-held wire has a length of 2-3 meters, which is specially designed for cleaning toilets. It can generally be bought at hardware stores. We put the wire in and we were able to solve the problem in a matter of minutes.

1. If there is a strange sound from the float inside the toilet, it may be that there are things in the toilet that have accumulated for a long time, resulting in a lot of sediment, so there will be abnormal noise. Generally, if it doesn't affect our use, you don't have to worry about it. If you are not at ease, it is recommended to contact a professional maintenance worker for on-site maintenance.

2. Generally, the float of the toilet bowl is damaged, and the water inlet of the toilet tank may seep or leak, even if only half of the water can be entered, as long as the water level can go up, and then adjust it to the water level we need.

3. If the float of the toilet is damaged or aging and not sealed, the water tank of the toilet will overflow, and we must replace the float or replace the sealing ring of the float.

It is best to be able to buy the model the same as the original.

2. What are the precautions for using the toilet.

1. We need to measure the bathroom before installing the toilet, so as to ensure that the toilet is installed more accurately.

2. Then check whether the water pipes are blocked, whether the ground is flat, and it is best to shorten the size of the sewer.

3. In order to make the horse barrel more stable, we had better put glass glue on the floor.

Control the distance between the toilet and the wall. After the toilet is installed, it is necessary to check whether the toilet flushes smoothly, whether the switch can be used normally, and so on.

4. It is best for us to buy a water tank that can adjust the amount of water, usually less than 6 liters is a water-saving type, if the model is too small, it cannot ensure that the toilet can be flushed.

What to do if the toilet floats up and still comes out of the water: Hello dear, I'm glad to answer the <> for you

There are generally several reasons for the flow of water. 1. One of the reasons for the first vertical key is that the flip cover is not covered, just resting on it, at this time, as long as it is manually hidden, if there is a leak on the flip cover, you need to change the flip cover. 2. If the float is resting underneath, there is no way to stop the water, just need to do it manually.

3. If the float's water-stop valve has no way to stop the water, or it has been running, it needs to be replaced.

When the toilet float can't control the water, this is because the density of the float is not enough to withstand the water pressure, causing the water to flow over, resulting in a situation where the float cannot control the water level. Let's take a look at how to fix this.

1.Adjust the height of the float.

The first thing you need to do is check that the float inside the toilet bowl is at the correct height, keeping it above the water line as much as possible. If the float is too low, it is necessary to adjust the height of the float by balancing the float wheel to ensure the normal operation of the float tube. By adjusting the float up and down, you can control the amount of water flowing in and out of the toilet.

2.Clean the float and float tube.

Accumulation of water inside the float and float tube can cause the water level to be unstable, so it is possible to stop this by cleaning the float and float tube frequently. Using a few simple household cleaners, such as white vinegar and baking soda, can remove bacteria and stains that have adhered to the surface.

3.Replace the toilet float.

If the above two solutions still do not solve the problem, then the float is too old or damaged to work properly. A new float will need to be replaced and then reinstalled. Choose the right type of float to replace, or contact a professional technician.

4.Adjust the water distribution valve of the water tank.

Sometimes, the misalignment between the float and the valve can lead to unstable water levels. In this case, the water distribution valve inside the tank can be adjusted so that it works on the same level as the float. Use the adjusting screws to adjust the position of the distribution valve and keep the float in the proper position.