What should I pay attention to when installing a household circulating water device?

If you are not at home when installing the water recirculator, you must turn off all the plugs. Like circulating water, it is impossible to flow hot water in the early stage, and hot water will only appear after cold water flows out, so don't be too anxious. It is best not to put the shower too close to the water heater.

This will affect the experience and waste water. Do not let the sun shine directly. The filter must be replaced at a certain time.

When installing circulating water and gas, we must pay attention to the upper and lower exits on the opposite side, and pay attention to the location of the unit, and also pay attention to the connection of the waterway system.

Be sure to pay attention to the adjustment of the water temperature, the circulating water device, when using it, you must also pay attention to the line, to prevent electric shock, and pay attention to the water heater and some other tap water to separate, but also to clean frequently, such a water device can be unplugged when not in use, it can also save power and safety, must meet the safety standards of the circulating water device, remember to regular ventilation, pay attention to the temperature requirements of the decoration materials at home, as much as possible to make every aspect a little more detailed.

Generally, the method of circulating water for home decoration can be divided into two types, one is to connect the circulating water pipe back to the water heater from the hot water pipe far away from the water heater. Then the second type is the end circulation, which connects each hot water outlet in series, and only uses the inner wire tee without the inner elbow. In fact, the role of adding circulating water is still very much, which can save water resources and do not need to use hot water to release a large amount of cold water.

1. You can connect the circulating water pipe to the farthest place from the water heater, so that the cold water will return to the water heater.

2. Connect each hot water outlet, you can only use the internal tee, although this is more troublesome, but this is the best to use, from the length of the circulation route can also be divided into large circulation and small circulation, the path of the large circulation will be relatively long, it is flowing through the branch pipeline, you can have instant heating.

Relatively good.

Have a great day! Happy every day

If you install a circulating water system at home, simply put, you can open the circulating water system when there is no water boiling anywhere before taking a shower, and pump back the frozen water from the hot water pipe (the water pipe from the water heater to the shower room) into the cold water pipe through internal circulation. When all the frozen water in the hot water pipe is circulated, the circulating water will automatically stop working, and then turn on the faucet for 1 to 3 seconds wherever there is hot water, and the hot water will be directly discharged. The cycle time is generally 30 seconds to 2 minutes, depending on the shower room.

The best way to recycle water for home improvement is the circulation of points and points, and the welding point can be next to the tooth of the circulating water pipe, so that when the hot water is turned on, if the points are connected to each other, the circulating pump will sense the cold water in the hot water pipe, and it will be pumped back into the hot water to be heated again, so that the cold water will not be wasted.

A filtration device can be installed on the inlet valve outside the house, so that the process of using water can be recycled.

First, buy a recirculating water system and install it under the floor of the restroom so that you can use it.

Circulating water in the waterway at home is zero cold water, is it better to go to a large circulation or a small circulation?

First, let's look at the difference between the big cycle and the small cycle. The small circulation means that the hot water only circulates in the main pipe, so the water from the main pipe to the faucet will cool, and the cold water will come out for a second or two when using the water. The large circulation will circulate to each water outlet point, and as soon as it is turned on, there will be hot water.

If you do zero cold water, of course, you want to turn on hot water, and it is best not to have cold water for a second, and it is definitely good to do a large circulation. However, if the circulation pipeline is too long, the pump may not move, or the water heater will leak because of the high pressure, of course, these problems are solved.

Some people may say that the small circulation is to use the cold water pipe to make the return pipe, which is inaccurate, although the use of cold water pipe to make the return pipe is a small circulation is good, but it is not recommended to do this, because once the cold water pipe is used as the return pipe, as long as the water heater at home is in standby mode and the water heater is not turned off, then any water outlet point will use water, the water heater will start, washing clothes, flushing the toilet is hot water. The following is an installation drawing with a return pipe and an installation drawing without a return pipe, which can be understood at a glance.

Therefore, the transformation of the hot water circulation system in the family needs to be planned and communicated in detail in the early stage, because whether it is a small cycle or a large cycle, it is not a fixed way, it is necessary to change flexibly according to the site, and finally we do the hot water circulation system at home, and we also need to keep all the hot water pipes insulated, which is also an indispensable part of the transformation.

I think it's better to do a large cycle, because it will be more convenient to use a large cycle.

I think if it is a family of three, it is better to do a small circulation, which is more water-saving.

The large circulation of waterway refers to the installation of water and electricity before the decoration of the house, and a return pipe is connected to the hot water circulation machine at the farthest end of the hot water pipe. In this case, there are three types of indoor water pipes: hot water, cold water, and return pipes. The small circulation of the waterway refers to the fact that the home decoration has been completed and the return pipe has not been installed, and the small circulation is to solve this problem.

The method is to connect the hot and cold water under the washbasin at the farthest end of the hot water through a one-way valve, and the hot water flows in the direction of the hot water to the cool water pipe.

Summary. Hello, from the perspective of low-carbon environmental protection, it is necessary to install household circulating water, because after installing circulating water equipment at home, it will reduce the water flow, reduce the calorific value of combustion, play a role in saving energy, and open it can directly produce hot water, so that users can feel a comfortable bathing environment.

Hello, from the perspective of low-carbon environmental protection, it is necessary to install household circulating water, because after installing circulating water equipment at home, it will reduce the water flow, reduce the calorific value of combustion, play a role in saving energy, and open it can directly produce hot water, so that users can feel a comfortable bathing environment.

Hello, from the perspective of low-carbon environmental protection, it is necessary to install household circulating water, because after installing circulating water equipment at home, it will reduce the water flow, reduce the calorific value of combustion, play a role in saving energy, and open it can directly produce hot water, so that users can feel a comfortable bathing environment.

Hello, there are two detailed ways to circulate water: 1. You can connect the circulating water pipe to the farthest place from the water heater, so that the cold water will return to the water heater. 2. Connect each hot water outlet, you can only use the internal tee, although this is more troublesome, but this is the best to use, from the length of the circulation route can also be divided into large circulation and small circulation, the path of the large circulation will be relatively long, it is flowing through the branch pipeline, you can have instant heating.

Relatively good.

Sincerely answer every question for you! Best if you're satisfied! If you have any questions, please keep asking!

Have a great day! Happy every day

1. The practice of circulating water for home improvement.

One is to connect the circulating water pipe from the hot water pipe farthest from the water heater back to the water heater.

The second is the end circulation, each hot water port is connected in series, no inner tooth elbow, only the inner wire tee.

2. The role of circulating water in home decoration.

First, it conserves water and does not have to release a lot of cold water before using hot water.

Second, save waiting time, turn on the hot water faucet to produce hot water, which is better to use in winter.

3. Schematic diagram of home improvement circulating water.

Method 1: Glass on both sides, with a fishing line in the middle, plus a small pump and a number of pipes. The survey results show that the investment in this practice is relatively high.

Because double glazing is expensive. Method 2: Use a glass and a small water pump.

The water is then pumped through a pipe to the upper end of the glass (the upper end of the glass uses a small platform similar to an aluminum alloy strip as a small platform for the water to flow down), and the water flows down the glass.

The method of circulating water for home decoration is: end circulation, each hot water outlet is connected in series, no inner tooth elbow, only internal tooth tee can be solved.

There are two working modes of the circulating pump, one is to work with water flu, and the other is to start the power supply, and the working mode is set according to the need. Give the pump a start signal, the circulating pump starts working, pressurize the cold water in the pipe into the water heater, and the water heater starts working.

When the hot water enters the hot water pipe, the circulating water device will stop working when the thermostat on the circulating water device senses that the hot water in the pipe has reached the pre-set temperature of the circulating water device. This is just a rough idea of how a circulating water device works. Another very important point is that the laying of hot water pipes is very important, whether the effect of circulating water is good or not, it is very important to lay pipes.

There are two ways to circulate water, one is to connect the circulating water pipe from the hot water pipe farthest from the water heater back to the water heater, and the other is to circulate at the end, and each hot water outlet is connected in series.

From the perspective of the length of the cycle path, there are two kinds of cycles: large cycles and small cycles. Large circulation, the circulation path is longer, the circulating water passes through the branch pipeline, the use experience is better, and there is hot water immediately when the faucet is opened.

Small circulation, the circulation path is short, the circulating water only circulates in the main pipeline, does not pass through the branch pipeline, the cost is slightly lower, but the use experience is slightly worse, it takes about 10 seconds to open the faucet, and the cold water in the branch can be discharged to have hot water. From the perspective of heat demand, there are kitchen and bathroom hot water circulation, heating hot water circulation and kitchen and bathroom + heating hot water circulation.

It's a circulating waterway for hot water, just make a whole pipe, and open three links on the pipe for hot water in each room.

As people's requirements for the quality of life are getting higher and higher, so circulating water has also become a must-install project for home installation. So that everyone can enjoy hot water in seconds with more peace of mind.

Household circulating water pipe layout: The hot water system (the so-called hot water system) has a main hot water pipe, which is divided into several layers. This water supply method should be a hot water return device, that is, a household circulating water system.

The specific method is: connect the water pipe to the bottom of the hot water source from the hot water ** end, circulate through the middle water pump, pump the cold water in the main pipe to the hot water source for new heating, and ensure that there is water and electricity after opening the faucet (because only the water in the main pipe is discharged, and there is still a small amount of water in the branch pipe when used). The circulating water pump can be controlled by temperature, time, manual or water flow switch.

Precautions for the installation of household circulating water system: The outdoor installation of household circulating water system should be in an outdoor place with good ventilation and easy operation (such as a ground floor courtyard or a high-rise open-air working balcony). It is strictly forbidden to install in a location where there are no standard guardrails and air conditioning outside the indoor small door, or in any position on an enclosed balcony that may affect the safe use and normal operation.

The household circulating water system itself is windproof and rainproof; There should be a floor drain or open ditch nearby, which is convenient for future drainage and pressure relief of the overflow valve; When the indoor type is placed on the balcony, the balcony must be closed; It is recommended to install it in the kitchen; Installation space on one side of the water heater nozzle (usually on the left side): at least 40cm on the left and right sides; At least 50 cm on the anterior side and at least 50 cm on the posterior side. Leave at least 1 metre of space on the front side.

When the circulating water system is turned on, hot water flows out of the shower, which is actually hot water. Facilitate life. The specific method of household circulating water pipe layout still needs to be set up on site according to the type and layout of the home.

Generally speaking, we recommend that when renovating a new home, all plumbing should be set up. For the sake of the aesthetics of the home, it is recommended not to make transparent pipes. However, if the family that has been renovated wants to redo the circulating duct, it is recommended to do the pigging for convenience.

Once the plumbing is ready, it is time to install a household circulating water system. As long as we can have the best master to design and install, we can ensure that you can use a comfortable and warm household circulating water system.

That's it"What should I pay attention to during the installation of the layout diagram of the circulating water pipeline for home decoration? "I hope it can help you!

It is necessary to pay attention to the quality of the circulating water agent, the budget, the location of the installation, and the professional to find a professional to install, and be sure to pay attention to safety when installing.

There should be open ditches and floor drains around, and they should be installed in a confined space, and when they are installed in the kitchen, the sprinkler head should be on the left side, and the interval between the left and right sides should be 40.

Pay attention to the power off, the quality of this kind of thing, replace the filter element inside the machine in time, the use of the machine, and the beauty of the house during installation.

To avoid conflicts between the home water circulation system and their own home environment, affecting the overall appearance, do not install external devices, avoid direct sunlight, and replace the filter element in time when the service life expires.

When we install, we will install the check valve at the connection between the hot water pipe and the cold water pipe under the washbasin at the farthest end of the water heater, so that if the machine works for a little longer, it will cause a little hot water when we use the cold water in the farthest wash basin, because when the machine works for a little longer, the hot water circulating from the machine will flow to the cold water pipe through the check valve. In this way, when we install the check valve wash basin, we will use cold water to produce a little hot water, which can also reduce or avoid the time of hot water when putting cold water through the time setting of the machine, which can generally be solved after several debugging.