What is the material of microcrystalline plate, the difference between microcrystalline panel and bl

The material of the microcrystalline plate is a mixture of microcrystalline and glass made from sintering and crystallizing glass particles.

It has the advantages of hard texture, uniform compactness, and no radioactive contamination of the product, and is a new type of environmentally friendly green material, and the microcrystalline plate also has the dual characteristics of glass and ceramic. It is used for protection and decoration, the overall light and thin, smooth surface, soft texture, and not easy to weather, deterioration and fading, damage, and the material stability is extremely high.

Microcrystalline stone wood flooring installation method:

1. Be sure to ensure the cleanliness of the ground, if there is unevenness of the ground, then deal with it, and then clean the dust.

2. The microcrystalline stone wood floor is paved directly on the ground, and there is no need to lay the keel.

3. There is no need to leave expansion joints between the paved floor and the wall, and before installing the beads and baseboards, install steel cards at the joints and ends of the two floors, and carefully connect the seams on the floor.

What are the advantages and disadvantages of microcrystalline:

1. Advantages. The texture of microcrystalline stone is very soft, because of its diffuse reflection effect, which can reflect the light evenly and visible to the naked eye, and there is a kind of ambilight effect when used for decoration.

This material has better advantages than natural stone, not only uniform texture, but also in terms of density, hardness, compression, bending, impact resistance, etc., the performance is very good, and there are no fine cracks on the surface of natural stone.

The color of microcrystalline stone is very rich, with beige, light gray white linen, crystal white and other major colors, which make up for the lack of natural stone color difference. It can not only be used for wall and floor decoration, but also as a decorative panel, which can be used for furniture, basins and other areas.

2. Disadvantages. Of course, the disadvantages of microcrystalline stone are also more obvious, although the surface gloss is high, but there must be no scratches, once scratched by metal, it will be easy to show scratches, which is very affecting the appearance.

In addition, there are a large number of pinholes on the surface, and if there are stains, they will be very noticeable and not easy to see. Although microcrystalline stone is decorative, if you want to use it splicing, each pattern cannot be matched, which affects the wholeness.

The difference between microcrystalline panels and black crystalline panels is their meaning, characteristics, and how they are used.

1. Differences in meaning.

A microcrystalline panel is a mixture of microcrystalline and glass made from the sintering and crystallization of appropriate glass particles. The black crystal panel is a panel dominated by black, and it is based on Schott in Germany.

Black crystal panels are the mainstay, and Hansen panels are the main ones in China.

2. Differences in characteristics.

The texture of the microcrystalline panel is hard, dense and uniform, with a natural and soft texture, high strength, and can be lightweight. And there is no pollution in the production process, and the product itself has no radioactive pollution, which is a new type of environmentally friendly green material.

Magnetic and thermal conductivity of black crystal panels.

Strong ability, high temperature resistance, delicate feel with smooth texture, not easy to break. The diameter of the pores on the panel is small, the particles are very fine, and it is not easy to change color and deformation after a period of use, and it is easy to clean.

3. Differences in use.

The material physical and chemical properties of microcrystalline panels are better than those of natural stone, traditional glass and ceramics, and can be used for building curtain walls.

And indoor decoration of various grades, it can also be used as mechanical structural materials, electronics, electrical insulation materials.

Substrate materials for large-scale integrated circuits, microwave oven heat-resistant utensils panels, chemical and anti-corrosion materials, and mine wear-resistant materials, etc.

Black crystal panels are mainly suitable for induction cookers on the market.

Microwave ovens, gas-electric dual-energy stoves, etc.

Sombra panels. Microcrystalline panels.

Microcrystalline. It is a new type of high-grade decorative material.

Microcrystalline stone is sintered through a special process under high temperature conditions similar to the formation conditions of granite, with uniform texture, high density, high hardness, compressive resistance, bending resistance, impact resistance and other properties that are superior to natural stone, durable, not easy to damage, and no fine cracks common to natural stone.

Microcrystalline is called glass-ceramic in the row.

Composite plate is a high-tech product that combines a layer of 3-5mm glass-ceramic on the surface of ceramic vitrified stone and is completely integrated after secondary sintering. The thickness of the glass-ceramic composite board is 13-18mm, and the gloss is high.

Greater than 95. <>

Development: in the field of building materials, since the 60s of the last century in the former Soviet Union.

The invention of calendering method to prepare microcrystalline withered coarse glass, and the later invention of Japan sintering method to prepare glass-ceramic for building decoration materials, this material because of its high-grade decorative arts, excellent mechanical properties.

Chemical resistance (weather resistance.

Raw materials are widely available, economic cost is low and gradually enter the high-end building materials market. Today, this clostile glass-ceramic building material is hailed as "the high-end decorative material of the 21st century".

With the development and development of glass-ceramic building materials, glass-ceramic composite panels came into being. It is a flat composite of glass-ceramic and glass-ceramic, showing many comprehensive advantages.

The above content reference: Encyclopedia - Microcrystalline Stone.

Microcrystalline stone is made of ceramic and glass composite through high-tech sintering, it has good permeability, texture can be imitated, and the color is high, so it is called ceramic glass stone stainless steel, it is a composite material.

It differs from pure crystalline materials and a considerable portion of solid materials. In these materials, the glass phase is usually very small (and in some cases, it is more), while glass-ceramic, especially in decorative building materials, contains more glass phase (sometimes up to 50%).

However, it is also very different from pure glass, which does not contain any crystalline phase under normal conditions, whereas glass-ceramic contains crystalline phases (mostly micron-sized microcrystalline phases).

The biggest difference between the microcrystalline phase and the glass phase is that the particles are arranged in an orderly manner in the internal structure of the former, while the particles are arranged in a remote disorder in the internal structure of the latter. The former will produce diffraction strips when irradiated by X-rays, while the latter will not produce diffraction strips.

Since glass-ceramic is a complex phase material of microcrystalline and glass phases, it has some properties of glass and some properties of crystal. Therefore, glass-ceramic combines the characteristics of both glass and crystalline materials, including ceramic materials.

Micro-cracking microcrystalline plate is a hybrid of microcrystalline and glass made by sintering and crystallizing glass particles. Microcrystalline plate texture is relatively hard and dense and uniform, no radioactive pollution, is a relatively new type of green environmental protection material, microcrystalline plate contains the dual characteristics of glass and ceramics, even if long-term exposure to polluted sail late air and wind and rain, will not fade and deteriorate, strength will not be reduced.

The water absorption rate of microcrystalline board is 0, generally there will be no water infiltration, no need to worry about movement or rust, if the surface is dirty, it is easier to clean, it can replace polymer density board and other materials.

Microcrystalline board can also be on the wall, this material is actually a relatively new type of high-end building decoration materials, and very environmentally friendly, in the production of natural inorganic materials, and then sintered at high temperature. The biggest feature of this material is that the surface is relatively smooth and clean, and the tone is very uniform, it looks more elegant, the color is particularly gorgeous, and the texture is relatively hard. The material itself is very environmentally friendly and also non-radiotoxic.

On the whole, the cost performance of this material is still quite high, and it has also become a new favorite for car key repair.

Microcrystalline board can be used as a cabinet, this material has many advantages, first of all, the wear resistance of this material is relatively high, so the service life of the cabinet will be very long, in addition, this material is not easy to be corroded, and the impact resistance is also very good.

The above is the content of the question of what kind of material is the microcrystalline plate, the microcrystalline plate is actually made of a lot of minerals or slag, and it will go through a series of procedures such as melting, rolling molding, crystallization, and annealing when making, and finally form a material with relatively high strength and very wear-resistant, this material is the microcrystalline plate.

Microcrystalline plate is a new type of high-strength, high-corrosion resistant and corrosion-resistant new high-tech industrial protective materials and building decoration materials formed by melting, calendering, crystallization and annealing with various slags as the main raw materials. Microcrystalline plate is a new type of high-strength, high-corrosion resistance and corrosion-resistant industrial protective materials and building decoration materials formed by melting, calendering, crystallization and annealing with various slags as the main raw materials.

Scope of use of microcrystalline plates:

1. Power generation industry: coal unloading ditch, coal hopper, coal storage bunker, dry coal grid, dumper, slag machine, water treatment, etc.

2. Chemical industry: anti-corrosion ground, pump foundation, etc.

3. Coal industry: wear-resistant lining plates in gangue silos, medium barrels, scrapers, bucket elevators, chutes, sieve funnels, etc.

4. Iron and steel industry: blast furnace mixing silo, sintering silo, feeder, ball making machine, etc.

Advantages of microcrystalline plate: high wear resistance, corrosion resistance, impact resistance, thin plate, smooth surface, large specifications, easy cutting and construction; Green environmental protection, no radioactive pollution, high brightness.

Disadvantages of microcrystalline plate: not wear-resistant, easy to leave scratches. It is easy to deform due to thermal expansion and contraction, and the corner surface is easy to warp. Due to the material itself, it has poor wear resistance, scratch resistance, flame retardant performance, and no stamping resistance. Hand Zhaofeng.